Instruction/ maintenance manual of the product AXB-REL8 AMX
Go to page of 12
instruction manual AXlink Bus Controllers AXB-REL8 Axcess R elay Controller.
AMX Limited W arranty and Disc laimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Co.
T able of Contents i AXB-REL8 Axcess Relay Controller T able of Contents Product Information ........ ................ ................. ................ .............. .............. ............ 1 Front and Rear Panels ................ .............
ii AXB-REL8 Axcess Relay Controller T able of Contents.
Product Information 1 AXB-REL8 Axcess Relay Controller Pr oduct Inf ormation The AXB-REL8 Relay Controller provides remote contro l for up to eight relay function s. Suitable for stand-alone or rack moun t applications, the AXB-REL8 may b e used with AX CESS or AXCENT systems via the four-wire AXlink data b us.
Product Information 2 AXB-REL8 Axcess Relay Controller Specifications (Cont.) Dimensions (HWD) 1.51" x 5.55" x 5.45" (3.84 cm x 14.10 cm x 13.
Connection and Wiring 3 AXB-REL8 Axcess Relay Controller Connection and Wiring Setting the DEVICE Dip Switch The eight-position Device DIP switch is located on the front panel of the AXB-REL8 as shown in FIG. 1 on page 1. Each de vice in the AXlink bus must ha ve a unique AXlink device number .
Connecti on and Wir ing 4 AXB-REL8 Axcess Relay Controller Preparing cap tive wires T o connect the wiring into a capti ve-wire connector: 1. Strip 1/4 inch off the wire insulation for all four wires. 2. T in 2/ 3 of the exposed wire. 3. Insert each wire into the appropriate cap ti ve-wire connector up to the insulation.
Connection and Wiring 5 AXB-REL8 Axcess Relay Controller AXlink data and po wer connections Connect the control system's AXlink connector to the AXlink connector on the rear panel of the AXB-REL8 for data and 12 VDC power as sho wn in FIG.
Connecti on and Wir ing 6 AXB-REL8 Axcess Relay Controller T esting the installation 1. Check AXlink status LED - it should blink once per second (see Specif i cations table for AXlink status LED). 2. Relay LED lights, but source does not acti vate: 3.
Connection and Wiring 7 AXB-REL8 Axcess Relay Controller System W orksheet and In stallation Guide AXB-REL8 Dealer ID# Dealer PO# Job SO# Description Ser ial# AXlink AXM GND PWR AXP B B 7 8 ABA 5 6 A .
AMX reserves the right to alter specif ications with out noti ce at an y time. brussels • dallas • los ang eles • mexico city • philad elphia • shanghai • singapor e • tampa • toronto* • yo rk 3000 research drive, richardson, TX 75082 USA • 469.
An important point after buying a device AMX AXB-REL8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AMX AXB-REL8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AMX AXB-REL8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AMX AXB-REL8 you will learn all the available features of the product, as well as information on its operation. The information that you get AMX AXB-REL8 will certainly help you make a decision on the purchase.
If you already are a holder of AMX AXB-REL8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AMX AXB-REL8.
However, one of the most important roles played by the user manual is to help in solving problems with AMX AXB-REL8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AMX AXB-REL8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
