Instruction/ maintenance manual of the product BB2250 Jonsered
Go to page of 17
Please read the operator’ s manual carefully and make sure you understand the instructions before using the machine. 115 32 10-26 English Operator’ s manual Original Instr uctions BB2250_English.
English 2 EC-declaration of conf ormity (Applies to Europe onl y) Husqvarna AB, SE-561 82 Huskv arna, Sweden, tel +46-36-146500, declares under sole responsibility that the blow ers Jonsered BB22 50 w.
English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
English 4 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blo wer concern critical points which must be taken into consideration to pre v ent possible serious bodily injury , and for this reason y ou are requested to read all such instructions carefully and follow them without fail.
English 5 For saf e operation and maintenance, symbols are car ved in relief on the machine. Using to these indications, please be careful not to make a mistak e.
English 6 WORKING CONDITIONS 1. Refrain from operating the b lower if y ou are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. T o reduce the r isk of hearing loss associated with sound lev els, hearing protection is required.
English 7 W ARNING Check to see if the shoc k-absorbers have become crac ked or otherwise damaged. Note that failing to replace these rubber and spring mounts when they have become crac ked or damaged may cause the engine to come loose fr om its frame during use, thus resulting in possib le serious bodily injury .
English 8 MAINTENANCE 1. In order to maintain your product in proper working order , perform the maintenance and checking oper ations described in the manual at regular intervals. 2. Alwa ys be sure to turn off the engine and disconnect the spark plug before perf orming any maintenance or checking procedures.
English 9 1. F rame 2. Harness 3. Engine Cov er 4. V olute Case, Cov er 5. Net 6. Air Cleaner 7. Recoil Star ter 8. Fuel T ank 9. Spark Plug Cap 10.Choke Lev er 11. Control handle 12. Stop Switch 13. Throttle Lev er 14. Elbow 15. Clamp (large) 16. Flexible hose 17.
English 10 MODEL BB2250 Dimensions (L x W x H) mm 401x460x495 Dry W eight (including pipes) kg 10.1 Dry W eight (without accessories) kg 9.4 Fuel T ank Capacity liter 2.
English 11 ■ FLEXIBLE HOSE AND SWIVEL JOINT 1. Connect the blo wer and s wivel joint with fle xible hose . Clamp both ends of the flexib le hose securely with the hardware supplied with the unit.
English 12 ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground f or fueling and move at least 10ft (3m) a way from the fueling point bef ore starting the engine .
English 13 ■ ST AR TING ENGINE IMPORT ANT • A void operating the b lower with the flexib le tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by o verheating. 1. Push the primer bulb until fuel flows out in the clear tube .
English 14 ■ ADJUSTING IDLE SPEED • The idling speed is set for 2000 rpm at the factory . If it is necessar y to adjust the idle speed, use the adjustment screw on the top side of carb uretor . (1) Idling Adjustment Screw ■ ST OPPING ENGINE • Mov e the throttle lev er to the idling position and set the stop s witch to the stop position.
English 15 Maintenance, replacement, or repair of the emission control de vice and systems ma y be performed by an y non-road engine repair establishment or individual. W ARNING Make sure that the engine has stopped and is cool before perf orming any service to the blower .
English 16 ■ SP ARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use . Remov e and inspect the spark plug ev ery 25 hours and clean the electrodes as necessary with a wire br ush. The spar k gap should be adjusted to .
English 17 ■ AIR INLET NET IMPORT ANT • Blown air is taken in fr om the air inlet net. If the air flow drops during opera- tion, stop the engine and inspect the air inlet net for bloc kage by obstac les. • Note that failure to remove an y such obstacles ma y result in the engine becoming overheated and damaged.
An important point after buying a device Jonsered BB2250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jonsered BB2250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jonsered BB2250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jonsered BB2250 you will learn all the available features of the product, as well as information on its operation. The information that you get Jonsered BB2250 will certainly help you make a decision on the purchase.
If you already are a holder of Jonsered BB2250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jonsered BB2250.
However, one of the most important roles played by the user manual is to help in solving problems with Jonsered BB2250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jonsered BB2250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
