Instruction/ maintenance manual of the product JMD-15 Jet Tools
Go to page of 30
OWNER'S MA NUA L JMD -15 /18/1 8P FN Mill/D rill Machin e (JM D-18 show n with opt i onal CS-18 stand) JET P.O. BO X 1349 Phone : 253-351- 6000 W MH Tool Gr oup Auburn, W A 98071-1349 Fax: 1-800-274-6840 www.wm htool group. com e-m ail j et@wm htool group.
2 Thi s m anual has been prepar ed f or t he owner and operator s of a JET M ill/Drill. I ts p u rp o s e, a sid e from m achi ne operat i on, is t o prom ot e saf ety thr ough the use of acc epted c orrec t operati ng and mai nt enance procedur es.
3 WARNING Re ad and under sta nd the entir e cont ents of this manual b efore attem pting set-up or oper ation of this mill/dr ill. 1. T h is machi ne i s d esig n ed an d inten d ed fo r use b y pro p erly t rain ed and experi enced p erso nn el o nl y.
4 Speci fi cati ons : JM D-15/18/18PFN Stoc k Num ber: JMD -15 ................................................................................................................................... 350017 JMD -18 .........................................
5 Ov er al l Di m ensions: JMD -15 .............................................................................................. 36 -1/2 ”L x 37- 1/2 ”W x 35- 1/2 ”H JMD -18 ......................................................................
6 Contents of the S hipping Container 1. Mill/ Dr ill Ma ch ine Acc essor y Package: 1. 1/2” Dri l l Chuck w/ Chuck Key 1. Adj ustabl e Carbi de F acem i l l 1. Facem i ll A rbor 2. Bol ts, Nuts, and W ashers t o Attac h Vis e to Tab le 1. 2-1/2” Angl e Vi se (JMD- 15) 1.
7 A ssemb ly 1. Screw r ubber handles ( A, Fi g. 1) ont o handle shaf t (B, F i g. 1). Sc rew handle s haf t int o downf eed hub (C, F i g. 1) and t i ght en. Fl at spot on shaf t accom m odat es a com bi nat i on or adj ustabl e wrench. Note: Handle shaft s ar e al r eady instal l ed i nt o hub on JMD- 18PFN.
8 Lubrication Lubri cat e ball oil ers (A, F i g. 4) f ound by t he X/Y- ax i s hand wheels, the oi l er f ound by t he rai sing/ l owering c rank handl e, and t he oil er on the f ront of t he bed once dai l y wit h Mobi l DT E Oi l Heav y Medi um .
9 Controls Longitudinal H and W hee ls: (X -axi s) (A, F ig. 6) Located on ei t her si de of the tabl e. Mov es table side t o side. Cross Feed Han d Wheel : (Y-axi s) (B, F ig. 6) Located on t he f ront of the base. Mov es tabl e t o wa r d , o r a wa y f r o m t h e c o l u m n .
10 Mo tor M ou n t L ock L ever: ( A ,F i g .9 ) Located on t he ri ght si de of t he head casti ng. Locks and unl ock s the m ot or m ount i ng pl ate enabli ng t he user to t ension v -bel ts. Head Pi vot L o ck: ( B ,F i g .9 ) Located on t he ri ght r ear of the head c asti ng.
11 4. Arrange t he v - bel ts (A, Fi g. 12) on the pull ey s (B, F i g. 12) f or the desir ed speed accor ding t o t he speed chart ( H, F i g. 11) on the bel t cov er. 5. Tension t he v -bel t s by pushing the m otor away f rom the head casti ng and lock i ng the m otor m ount l oc k lev er (F , F i g.
12 Gib A djustment Af t er a period of t i m e, m ov em ent of t he t abl e ov er t he ways wil l cause norm al wear. T o adjust t he gi bs f or thi s wear: 1. The hori z ontal gib adj ustm ent s crew (A, F i g. 13) i s f ound t o the ri ght on t he tabl e f ace.
13 JM D- 15 H ead A ss em bl y.
14 P a rt s List for th e J MD-1 5 Mill/ Dr ill H ead A ss embl y Index Pa rt No. No . Descrip ti on Siz e Qty. 1 .......... JMD1 5-0 01 .................. D raw bar ............................................................. .......................
15 Index Pa rt No. No . Descrip ti on Siz e Qty. 67 ........ JMD15 -0 67 .................. Mo tor ................................................................. 1HP, 1 Ph .................... 1 ............ JMD1 5- 067A ................ C apacit or (not shown) .
16 Index Pa rt No. No . Descrip ti on Siz e Qty. 15 4 ...... TS- 0561071 ................. H ex Nu t ............................................................. 5/8” ............................. 2 15 5 ...... TS- 0680031 ................. W as he r .
17 JM D- 15 Tabl e, Base, an d Col um n A ss em bl y.
18 Parts L i st f or JM D- 15 T a b le, Ba se , a nd C olu mn A sse mbly Index Pa rt No. No . Descrip ti on Siz e Qty. 1 .......... JMD1 8-2 01 .................. Table Ha nd W heel ............................................. .......................
19 JM D- 18/18PFN H ead A s sem bly.
20 P a rt s List for th e J MD-1 8 Mill/ Dr ill H ead A ss embl y Index Pa rt No. No . Descrip ti on Siz e Qty. 1 .......... JMD1 8N -00 1 ................ Head Bod y......................................................... ...........................
21 Index Pa rt No. No . Descrip ti on Siz e Qty. 32 ........ JMD18 -0 47 .................. R ound Head Screw ............................................ 3/1 6”x3/8 ” ................... 2 33 ........ JMD18 N- 03 3 ................ Micro Adjus ting Ind icato r .
22 Index Pa rt No. No . Descrip ti on Siz e Qty. 82 ........ TS- 0680031 ................. W ash er.............................................................. 5/16 ” ........................... 2 83 ........ TS- 0051071 ................. He x Hea d Bo lt .
23 JM D- 18 Tabl e, Base, an d Col um n A ss em bl y.
24 P a rt s List for th e J MD-1 8 Mill/ Dr ill T a b le, Ba se , a nd C olu mn A sse mbly Index Pa rt No. No . Descrip ti on Siz e Qty. 60 1 ......... JMD1 8- 22 8 ............... Table ................................................................
25 Index Pa rt No. No . Descrip ti on Siz e Qty. 635-6 ...... JMD1 8- 36 6 ............... Pin ..................................................................... 5x38 ........................... 1 63 6 ......... JMD1 8N -6 36............. Column Bas e .
26 JM D- 18PFN Po wer Feed A s sem bly.
27 Pa rts List for the J MD-18PFN P owe r F e e d Assembly Index Pa rt No. No . Descrip ti on Siz e Qty. 24 8 ......... 290111 ...................... Main Pulley........................................................ .................................
28 Index Pa rt No. No . Descrip ti on Siz e Qty. 403-1 ...... 2450048 .................... W orm Gear Cov er ............................................. ................................... 1 403-2 ...... JMD1 8P FN-3 46 ........ Fl at C ros s H ea d S crew .
29 Wi ring Diagram JM D-15.
30 Wi ring Di agram JM D- 18 230V Only.
An important point after buying a device Jet Tools JMD-15 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools JMD-15 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools JMD-15 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools JMD-15 you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools JMD-15 will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools JMD-15, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools JMD-15.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools JMD-15. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools JMD-15 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
