Instruction/ maintenance manual of the product GH-1440W Jet Tools
Go to page of 24
OW NER’S M A NU A L GH-1340W/1440W La th es JET EQU IPMEN T & TOOLS , IN C. P.O. BO X 134 9 253-351-600 0 A W MH C ompany Auburn, WA 98071-1349 Fax 253-939-8001 www.
2 Important Information 1-YE AR J ET of fe rs a on e -yea r limite d LIM ITED W A RRA N T Y warranty on this product R E PL A C EM EN T P A R TS Replac em en t parts f or t his t ool are av ailabl e dir ectly f orm JE T Equipment & Tool s. To pl ace an order, call 1-800- 274-6848.
3 WARNING • Read an d understan d the entire in struction manu al befo re att em pt ing assembl y or oper ati on . • Th ese l athes are designed and i nt ended f or u se by p rop erly trai ned a nd experien ced perso nnel o nly.
4 Speci fi cati ons : GH -1340W/ 14 40W Stoc k Nu mber .............................................................................................. 321810 G H-1340W - 1 Stoc k Nu mber .................................................................
5 Miscellane ous: Steady Rest Capaci t y ................................................................................................. 1/4" - 3 -3/4 " Foll ow Rest Capacit y ...............................................................
6 WARNING Read an d understan d the entire con tents of this manua l b ef ore attemp ting se t-up or oper ati on! Fai lure to co m pl y may cause serious injur y! Contents of the Shipping Container 1 .
7 U ncr ati ng an d Cl ean- U p 1. Fi nish removi ng the wooden crate f rom around the l at he. 2. Unbolt t he lathe f r o m the s hi pping c rate bo tto m. 3. Choose a l ocation f or t he lat he that is dr y, has good li ghti ng, and has enough room to be abl e to ser v i ce the lat he on all four sides.
8 Chuck Pre par ation (T hree Jaw) WARNING Read an d understan d all direct ions for chuc k pre par atio n! Fai lure to co m pl y may cause serious in jury and/ or dam age t o t he lathe! Note: B e f ore r e m oving the chuc k from the spindl e, pl ace a w ay board ac ross the bedways un der t he c huck 1.
9 Lubrication CAUTION Lat he must b e servi ced at all lub rication poi nts and all reservoi rs fill ed to operat ing level befo re the lathe i s pu t into servi ce! Fai lure to co m pl y may cause serious d am ag e to th e l a th e! 1. Headst ock - Oi l m ust be up to i ndi cator m ark i n oil s i ght g l ass ( A, Fig.
1 0 3. Ap r o n - o il m ust be up t o i ndic a tor mark i n oil sight glass (A , Fig. 6). T op o ff with Mobi l DTE O i l H e av y M e di um . R em ov e oil cap (B, Fi g. 6) on top o f apr on to fill . To drai n, remove dr ain pl ug on bottom of apron.
1 1 Coolant Preparation CAUTION Fol low cool ant manu factu rer's recommen datio ns fo r use, care, and di sposal. 1. Re m o ve rear acce ss cov er on ta ilstock end. Make sure cool ant tank has not shif ted duri ng transport and i s loc a ted properl y under t he recovery chute (Fig.
1 2 Make sure t he l athe i s prop erly g rounded. Power is connect ed properl y when pu llin g up on the f orward-rev erse l e v er causes the spindl e to r otate counter -cloc kwise as v i ew ed from t he tail stock.
1 3 Gene ral Des cri pt i on Lathe B e d The l athe bed (A, Fi g. 10) is made of high grade cast i ron. By co m bi n i ng h i gh cheeks with str ong cross ri bs, a bed with low v ibr ation and high r igi d i ty is reali zed.
1 4 Tails t ock The tail stock (A , Fig. 12) slides on a v- w ay and can be l ocked at any loc ation by a cl amping l e v er. T he tail stock has a heavy duty spi ndle wi th a Morse Taper #3. Lead screw and F eed Rod The l eadscrew (B Fig. 12) and feed rod (C, Fi g.
1 5 Foll ow Rest The trav e li ng f oll ow rest (F, F ig. 12) i s m ounted on the saddle and f ollows the m o v ement o f the tur ning t ool . O nly two finger s are requi red as the pl ace o f t he thir d is tak en by the t urning t ool. The f o l low rest i s us ed f or tuni ng operati ons on long, sl ender workpi eces.
1 6 5. Feed /Lead S electo r Lever ( H ,F i g .1 3 )- loc ated on the f ront o f the gearbox. Used in set ting up for f eeding and threadi ng. Posit ions "F " and "D" are f or the feed r od . Posit ions "E" and "C" are for t he f eed screw.
1 7 15. Tool P ost Clampi ng Lever ( J ,F i g .1 4 )- loca ted o n to p o f the too l pos t. Ro tate counter -cl ockwi se to l oosen and cl ockwise to ti ghten. 16. T ailstock Qu ill Clampi ng Lever (A, F i g . 15) - l ocat ed on t he t a i lstoc k. Lift up to loc k the spindl e.
1 8 Oper ati on Feed and Th read Selecti on 1. Ref erence t he f eed and t hread found on the gear box f aceplat e tabl es (A, Fi g. 17 & page 22 of manual ). 2. Mo v e le v ers (B , C, D, E & F, F i g. 17) to the appropr iat e positi ons accordi ng to the chart .
1 9 Automat ic F eed Operation and F eed Chang es 1. Mov e the f orward/rev erse selec tor ( A, Fi g. 19) up or down dependi ng on desir ed dir ecti on. 2. Set selec tor levers (A, B , C, & D, Fi g. 20) to desi red rat e. Note: f or f eeding, l ever ( D) will be set at "F " or "D", dependi ng on desired f eed rate.
2 0 M etr i c Thr e ad Ta bl e I nch Lead and Feed T abl e Cross Fee d Ta ble.
2 1 Com pou nd R es t The com pound rest i s l ocat ed on top o f t he cros s s li de and can be r otated 360 degrees. Loosen the t wo s ocket head cap scre ws (A, Fi g. 21) on the c ompound rest base. Ther e is a cali brated di al (i n degr ees B, Fig.
2 2 Tails t ock If the handl e will not l ock the tailstoc k, foll ow the proc edure bel ow : 1. Lower the handl e t o the unl ocked posit ion. 2 . S l i d et h e t a i l s t o c kt oa na r e at h a ta l l o w s acces s to the undersi de o f t he tail stock.
2 3 4. Set up and c ut along fiv e i nches of t he bar stock. 5. Using a mi cromet er, m easure t he bar stock nex t to the c huck and at the end. The m easurem ent shoul d be t he same. 6. If the m easurem ents are not the sam e and adjust ment i s requi red, loosen hex socket cap scr ews (A , Fig.
2 4 Bel t Rep lacem ent and A djus tmen t 1. Disco nnect mach ine from the p ower sou rce (unplug ). 2. Open t he end gear cover and l ower co v er on the headstoc k side. 3. Take t ension off old belts by l oosening m o t or mount hex nut (A, Fi g. 26).
An important point after buying a device Jet Tools GH-1440W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools GH-1440W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools GH-1440W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools GH-1440W you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools GH-1440W will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools GH-1440W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools GH-1440W.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools GH-1440W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools GH-1440W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
