Instruction/ maintenance manual of the product JiMS-125 Jensen
Go to page of 18
® DOCKING DIGIT AL MUSIC SYSTEM FOR iPod OWNER'S MANUAL JiMS-125 ® (iPod Not Included) PLEASE READ THIS OPERA TING MANUAL COMPLETEL Y BEFORE OPERA TING THIS UNIT A ND RET AIN THIS BOOKLET FOR F.
® DEAR JENSEN CUSTOMER IMPORTANT SAFETY INSTRUCTIONS COMPLIANCE WITH FCC REGULATIONS PRODUCT FEA TURES INSTALLA TION LOCATION OF CONTROLS CLOCK SETTING ALARM OPERA TIONS RADIO OPERA TIONS iPod DOCKIN.
2 Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.
3 IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However , improper use can result in potential electrical shock or fire hazards.
4 10.Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire of electric shock. 11.Damage Requiring Service This unit should be serviced by qualified service personnel when: A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 PRODUCT FEA TURES JiMS-125 is an iPod Docking Music System which incorporates the • iPod , iPod mini, iPod classic, iPod touch and iPod nano Player / Re-charger • AM / FM Stereo receiver with di.
7 INSTALLA TION Clock setting battery back-up The battery back-up compartment is located on the back of the unit. (1) Remove the battery compartment door . (2) Follow the polarity diagram shown inside the compartment and install 2 x AAA batteries (not included) .
8 Main Unit Front view T op view 1 2 3 5 4 6 8 9 12 7 11 10 14 14 13 1. iPod docking station 2. iPod docking connector 3. Function switch : Power Off ; select RADIO / iPOD / AUX modes. 4. Band switch : 5. VOLUME knob : 6. TUNING knob : 7. SNOOZE button : Activate the snooze function.
18. DC-in jack : For the connection of external DC power supply 19. FM Antenna wire 20. Battery Compartment 21. RESET button : Reset the unit. 9 LOCATION OF CONTROLS Remote Control (for iPod only) 1. Infra-red T ransmitter 2. iPod PLAY / P AUSE button 3.
ALARM OPERATIONS Setting Alarm Time 1. With the unit powered of f, press & hold the ALARM SET button to display Alarm time, the alarm indicator flashes on LCD; then press the (HOUR) / (MINUTE) buttons to set the alarm time. 2. After the alarm time is set, release the ALARM SET button.
Wake to Radio Snooze Funtion - Y ou can activate the Snooze function manually after the alarm sounds by pressing the SNOOZE button once. Alarm will sound again in 5 minutes and snooze can be manually activated again within 1 hour - After the alarm sounds you can also press the ALARM ON / OFF button to stop it immediately .
12 RADIO OPERA TIONS Radio Operation extend the FM Antenna wire for the best reception. 1. Slide the FUNCTION switch to RADIO mode. 2. Slide the BAND switch to select FM Stereo / FM or AM band. 3. Rotate the TUNING knob and tune to a desired station. 4.
13 iPod DOCKING If the docking port will not be used for an extended period of time, it is recommended to cover the docking port by using the “Dock Cover” insert (included). 1. Use the iPod adaptor included in your iPod and insert it into the docking area.
The unit provides the auxiliary audio signal input for the connection of an external audio device. You may connect an audio cable with 3.5 mm stereo plug (not included) to the AUX IN Jack located at rear of the unit.
CARE AND MAINTENANCE • Do not subject the unit to excessive force, shock, dust or extreme temperature. • Do not tamper with the unit's internal components. • Clean your unit with a damp (never wet) cloth. Solvents or detergents should never be used.
Symptom Possible Problem Solution The unit does not respond (no power) AC A daptor is not plugged into a wall outlet or the connector is not plugged into the power supply jack on the back of the unit. Plug the A C adaptor into a wall outlet and plug the connector into the supply jack on the unit.
Printed in China SPECIFICATIONS Power Requirement Main unit DC input: DC10V , 1000mA Battery back up for clock: 2 X DC1.5V 'AAA' (UM-4) Batteries Remote Control 1 X CR2032 Lithium Battery Fr.
An important point after buying a device Jensen JiMS-125 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jensen JiMS-125 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jensen JiMS-125 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jensen JiMS-125 you will learn all the available features of the product, as well as information on its operation. The information that you get Jensen JiMS-125 will certainly help you make a decision on the purchase.
If you already are a holder of Jensen JiMS-125, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jensen JiMS-125.
However, one of the most important roles played by the user manual is to help in solving problems with Jensen JiMS-125. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jensen JiMS-125 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
