Instruction/ maintenance manual of the product Grand Cherokee (2009) Jeep
Go to page of 521
GRAND CHER OKEE 2009 ow n er’ s man u a l 2009 GRAND CHEROKEE Chrysler LL C 81-326-0954 Second Edition Printed in U.S.A. 150920 GrCherokee.indd 1 9/9/08 8:33:17 AM I n f o r m a t i o n P r o v i d .
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 Rollover W arning ....................... 5 䡵 How T o Use This Manual .................. 6 䡵 W arnings And Cautions ................... 8 䡵 V ehicle Identification Number .
INTRODUCTION This is a specialized utility vehicle designed for both on-road and of f-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differ ently fr om many passenger cars both on-road and off-r oad, so take time to become familiar with your vehicle.
NOTE: After you read the manual, it should be stored in the vehicle for convenient r eference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings.
Failure to use driver and passenger seat belts pr ovided is a major cause of severe or fatal injury . In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually .
INTRODUCTION 7 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against pr oce- dures that could result in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 4 ▫ W ir eless Ignition Node (WIN) ............ 1 4 ▫ Integrated Ignition Key ................. 1 5 ▫ Ignition Key Removal .................. 1 5 ▫ Key-In-Ignition Reminder .
▫ Express Down W indow Feature — If Equipped ........................... 2 4 ▫ Using The Panic Alarm ................. 2 5 ▫ Programming Additional T ransmitters ...... 2 5 ▫ T ransmitter Battery Service .............. 2 5 ▫ General Information .
▫ Seat Belts And Pregnant W omen .......... 4 5 ▫ Seat Belt Extender ..................... 4 5 ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) ................. 4 6 ▫ Child Restraints ...................... 5 8 䡵 Engine Break-In Recommendations .
A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a W ireless Ignition Node (WIN) with integral ignition switch. Y ou can insert the double-sided key into the ignition switch with either side up.
Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key , which stor es in the r ear of the RKE transmitter . The valet key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
NOTE: • If you try to remove the key before you place the shift lever in P ARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly , then remove the key as described.
Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key . NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the LOCK or ACC position.
NOTE: • The Sentry Key 威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
NOTE: When having the Sentry Key 威 Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer . Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can pr ogram new transmitters to the system by performing the following procedur e: 1.
General Information The Sentry Key 威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undes- ired operation.
V ehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the V ehicle Security Alarm success- fully arms, the V ehicle Security Light will flash at a slower rate to indicate the alarm is set.
Keyless Entry (RKE) transmitter . The RKE transmitter does not need not be pointed at the vehicle to activate the system. NOTE: Inserting the RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however , the buttons on the remaining RKE transmitters will continue to work.
Remote Key Unlock, Driver Door/All Doors First Press This feature lets you pr ogram the system to unlock either the driver’s door , or all doors, on the first press of the UNLOCK button on the RKE transmitter .
T o Lock the Doors Press and release the LOCK button on the RKE transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter .
Using the Panic Alarm T o turn the Panic Alarm feature on or off, pr ess and hold the P ANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
1. Battery access is thr ough a door located on the rear of the fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door . 2. Remove and replace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterioration.
If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the RKE transmitter . The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios.
NOTE: • If an engine fault is present the vehicle will start and then shut down 10 seconds later . • The park lamps will turn on and remain on during Remote Start mode. • For security , power window and power sunroof op- eration (if equipped) ar e disabled when the vehicle is in the Remote Start mode.
DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door .
If you pr ess the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
WINDOWS Power Windows The power window contr ols are located on the driver’s door trim panel. Ther e is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSOR Y position.
Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically . T o cancel the “Auto Down” movement, operate the switch in either the up or down dir ection and release the switch.
Resetting the Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be r eset. T o reset Auto Up: Pull the window switch up and close the window com- pletely , then pull and hold the switch for one second.
open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunr oof open, adjust the sunroof opening to minimize the buffeting. LIFTGA TE T o open the liftgate, pull up (squeeze) on the handle and lift.
Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. T o open the flipper glass, push up on the window switch located on the liftgate. W ARNING! T o avoid injury , stand back when opening. Glass may automatically rise.
W ARNING! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle ar e the restraint systems.
W ARNING! (Continued) • Buckle up even though you are an excellent driver , even on short trips. Someone on the road may be a poor driver and cause a collision which includes you.
W ARNING! (Continued) • T wo people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly . Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.
W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! (Continued) • A belt that is worn under your arm is very danger- ous. Y our body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury . A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones.
6. T o release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow it to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
How to Disengage the Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking mode and activate the V ehicle Sensitive (Emer- gency) Locking mode.
NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly . The pretensioners are triggered by the Occupant Re- straint Control (ORC). Like the fr ont airbags, the preten- sioners are a single use item.
3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled. 4. T urn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.
W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
The fr ont airbags have a multistage inflator design. This may allow the airbags to have differ ent rates of inflation that are based on collision severity and occupant size. This vehicle is equipped with window bags to pr otect the driver , and front and rear passengers sitting next to a window .
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
front airbags work with the instrument panel knee bol- sters to provide impr oved pr otection for the driver and front passenger . W indow bags also work with seat belts to improve occupant pr otection. The seat belts ar e designed to pr otect you in many types of collisions.
Y ou should read the instructions provided with your child r estraint to make sure that you are using it properly . 2. All occupants should use their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate.
Airbag System Components The airbag system consists of the following: • Occupant Restraint Control (ORC) • Airbag W arning Light • Driver Airbag • Passenger Airbag • Side Curtain Airbags abo.
• The ORC also turns on the Airbag W arning Light for 2.5 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the Airbag W arning Light will turn of f. If the ORC detects a malfunction in any part of the system, it turns on the Airbag W arning Light either momentarily or continuously .
• The Side Impact SRS Side Curtain Airbags are de- signed to activate only in certain side or rollover collisions. When the Occupant Restraint Control (ORC) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle, and both sides of the vehicle when rollover is sensed.
abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor . They ar e not caused by contact with chemicals. They are not permanent and normally heal quickly . However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately .
NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven. Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it.
Airbag W arning Light Y ou will want to have the airbag system r eady to inflate for your protection in an impact. The airbag system is designed to be maintenance free.
• Under certain cir cumstances, EDR data may not be recor ded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data m.
4. Otherwise required by law . Data parameters that may be recor ded: • Diagnostic trouble code(s) and warning lamp status for electr onically-controlled safety systems, including the airbag system .
enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child. Use the restraint that is correct for your child. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle.
W ARNING! • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passen- ger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Improper installation can lead to failure of an infant or child restraint.
designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of .
NOTE: For additional information refer to www .seatcheck.org or call 1-866-SEA TCHECK. Older Children and Child Restraints Children who weigh mor e than 20 lbs (9 kg), and who are older than one year , can ride forward-facing in the vehicle.
LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH.
If you are installing LA TCH-compatible child restraints in adjacent rear seating positions, you can use the LA TCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position.
In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secur e, try a differ ent seating position. T o attach a child restraint tether strap: Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat.
W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. T ransporting Pets Airbags deploying in the front seat could harm your pet.
A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of dif ficulty . SAFETY TIPS T ransporting Passengers NEVER TRANSPORT P ASSENGERS IN THE CARGO AREA.
Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling contr ols to for ce outside air into the vehicle.
Airbag W arning Light The light should come on and r emain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer . If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer .
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 7 8 ▫ Inside Day/Night Mirror ................ 7 8 ▫ Automatic Dimming Mirror — If Equipped . . . 78 ▫ Outside Mirrors ...................... 7 9 ▫ Outside Mirrors Folding Featur e .
▫ General Information .................. 1 1 0 䡵 V oice Recognition System (VR) — If Equipped .......................... 1 1 0 ▫ V oice Recognition System (VR) Operation . . . 1 10 ▫ Commands ........................ 1 1 2 ▫ V oice T raining .
▫ Headlights And Parking Lights .......... 1 3 0 ▫ Automatic Headlight System — If Equipped ........................ 1 3 1 ▫ SmartBeams — If Equipped ............. 1 3 2 ▫ Daytime Running Lights — If Equipped .... 1 3 3 ▫ Automatic Headlight Leveling — HID Headlights Only .
▫ T o Resume Speed .................... 1 4 6 ▫ T o V ary The Speed Setting .............. 1 4 6 ▫ T o Accelerate For Passing .............. 1 4 7 䡵 Rear Park Assist — If Equipped ........... 1 4 7 ▫ Rear Park Assist Sensors ..............
▫ Opening Sunroof — Expr ess ............ 1 6 1 ▫ Closing Sunroof — Expr ess ............. 1 6 1 ▫ Pinch Protect Featur e ................. 1 6 1 ▫ Pinch Protect Override ................ 1 6 2 ▫ V enting Sunroof — Expr ess ...........
MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror . The mirror should be adjusted to center on the view through the r ear window .
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: full forwar d, full rearwar d and normal.
Power mirror pr eselected positions can be controlled by the optional Memory Seat Featur e. Refer to “Driver Memory Seat” in this Section for further information. Heated Mirrors — If Equipped These mirr ors ar e heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster .
uconnect 姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect 威 phone. Refer to your “Navigation User’s Manual” for uconnect 威 phone operating instruc- tions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate.
The uconnect 威 phone is driven through your Bluetooth 威 “Hands-Free Profile” cellular phone. uconnect 威 features Bluetooth 威 technology - the global standard that enables differ ent electr.
can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts fr om the uconnect 威 phone such as ⬙ CELL ⬙ or caller ID on certain radios.
Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙ Help ⬙ following the beep. The uconnect 威 phone will play all the options at any prompt if you ask for help. T o activate the uconnect 威 phone fr om idle, simply pr ess the PHONE button and follow the audible prompts for directions.
• For identification purposes, you will be prompted to give the uconnect 威 phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • Y ou will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority .
• The system will prompt you to say the name of the person you want to call. • After the ⬙ Ready ⬙ pr ompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a previ- ously stored name entry in the uconnect 威 phonebook or downloaded phonebook.
The uconnect 威 phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
• This downloaded phonebook cannot be edited or deleted on the uconnect 威 phone. These can only be edited on the cellular phone. The changes are trans- ferred and updated to uconnect 威 phone on the next phone connection.
Edit uconnect 威 Phonebook Entries NOTE: • Editing names in the phonebook is r ecommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. • Press the PHONE button to begin. • After the ⬙ Ready ⬙ pr ompt and the following beep, say ⬙ Phonebook Edit.
• After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. Y ou can either say the name of a phonebook entry that you wish to delete or you can say ⬙ List Names ⬙ to hear a list of the entries in the phonebook from which you choose.
• After the ⬙ Ready ⬙ pr ompt and the following beep, say ⬙ Phonebook List Names. ⬙ • The uconnect 威 phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available.
cellular phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The uconnect 威 phone compatible phones in the market today do not support r ejecting an incoming call when another call is in progr ess. Ther efore, the user can only answer an incoming call or ignore it.
Three-W ay Calling T o initiate three-way calling, press the VOICE RECOG- NITION button while a call is in progress, and make a second phone call, as described under ⬙ Making a Second Call While Current Call is in Pr ogress.
• After the ignition key is switched to OFF , a call can continue on the uconnect 威 phone for a certain dura- tion, after which the call is automatically transferred from the uconnect 威 phone to the cellular phone. • An active call is automatically transferred to the cellular phone after the ignition key is switched to OFF .
If the phone is not reachable and the uconnect 威 phone is operational, you may reach the emergency number as follows: • Press the PHONE button to begin. • After the ⬙ Ready ⬙ pr ompt and the following beep, say ⬙ Emergency ⬙ and the uconnect 威 phone will instruct the paired cellular phone to call the emer gency num- ber .
T owing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the ⬙ Ready ⬙ pr ompt and the following beep, say ⬙ T owing Assistance. ⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.
When calling a number with your uconnect 威 phone that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can press the VOICE RECOGNITION button and say the sequence you wish to enter , followed by the word ⬙ Send.
T urning Confirmation Prompts ON/OFF T urning confirmation prompts off will stop the system from confirming your choices (e.g., the uconnect 威 phone will not repeat a phone number befor e you dial it). • Press the PHONE button to begin. • After the ⬙ Ready ⬙ pr ompt and the following beep, say ⬙ Setup Confirmations.
Mute/Un-Mute (Mute OFF) When you mute the uconnect 威 phone, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. In order to mute the uconnect 威 phone: • Press the VOICE RECOGNITION button.
• The uconnect 威 phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority . T o “select” or “delete” a paired phone being announced, press the VOICE RECOGNITION button and say “Select” or “Delete.
Things Y ou Should Know About Y our uconnect 姞 phone uconnect 威 phone T utorial T o hear a brief tutorial of the system featur es, pr ess the PHONE button and say “uconnect 威 T utorial.
• Speak normally , without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period.
• In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, •.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3 I n f o r m a t i o n P r o v i d e d b y :.
106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 107 3 I n f o r m a t i o n P r o v i d e d b y :.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will pr esent you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command.
Commands The V oice Recognition system understands two types of commands. Universal commands ar e available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the VR button.
Radio FM T o switch to the FM band say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the fr equency) • “Next Station” (to select th.
Memo T o switch to the voice r ecorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to r ecord a new memo) — During the recor ding you may pr ess the VR button to stop r ecord- ing.
NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. V oice T raining For users experiencing difficulty with the system recog- nizing their voice commands or numbers, uconnect 威 phone V oice T raining feature may be used.
Front Seat Adjustment — Recline T o adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. T o return the seatback, lift the lever , lean forward, and r elease the lever .
Eight-W ay Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch contr ols up/down, forward/r earward, and tilt adjustment. The top switch controls the seatback recline adjustment.
NOTE: The four-way seat does not have an up/down adjustment. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear . Adjustable head restraints should be adjusted so that the upper edge is as High as practical.
After turning the ignition ON, you can choose from a High or Low heat setting. Illuminated LEDs on each switch indicate the level of heat in use. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating.
W ARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal High-level. If the High-level setting is selected, the system will automatically switch to Low-level after approximately 30 minutes of continuous operation.
60/40 Split Rear Seat T o Lower Rear Seat Either side of the rear seat can be lowered to allow for extended car go space and still maintain some r ear seating room. NOTE: Be sure that the front seats are fully upright and positioned forward. This will allow the r ear seatback to fold down easily .
T o Raise Rear Seat Raise the r ear seatback and lock it into place. If interfer- ence from the car go area prevents the seatback fr om fully locking, you will have difficulty returning the seat to its proper position.
Storage (Rear Seat Armrest) — If Equipped The rear seat may be equipped with a center storage armrest. Press the latch and lift the top of the armr est to access the storage bin.
Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. Y our vehicle is equipped with two RKE transmitters.
4. Adjust the brake and accelerator pedals to the desired positions. 5. T urn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). 6. T urn the ignition switch to the LOCK position and remove the key . 7. Press and release the S (SET) button located on the driver’s door .
T o r ecall the memory setting for driver two, press memory button number 2 on the driver’s door , or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (S, 1, or 2).
Easy Entry/Exit Seat This feature pr ovides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There ar e two possible Easy Entry/Exit adjustments available: • The seat cushion will move rearwar d approximately 2.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door . 2. Reach under the hood, move safety latch to the left, and lift the hood. CAUTION! T o prevent possible damage, do not slam the hood to close it.
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
Automatic Headlight System — If Equipped T urn the end of the multifunction lever to the third detent to activate the automatic headlight system. This system performs two functions. W ith the engine running and the multifunction lever in the AUTO posi- tion, the headlights will turn on and off based on the surrounding light levels.
SmartBeams — If Equipped The SmartBeam system provides increased forwar d light- ing at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror . This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view .
T o Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system.
Instrument Panel and Interior Lights When the multifunction lever is in the parking light, headlight, or AUTO position (if equipped), rotating the center portion of the lever up and down will increase and decrease the brightness (dimmer control) of the instru- ment panel lights.
Battery Saver Feature If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the LOCK position, the battery saver feature will automatically turn of f the exterior and interior lights after eight minutes.
NOTE: • T urning on the high beam headlights turns off the fog lights. • A front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow , or dust. The front fog lights supple- ment the lower beam of a standard headlight system.
High Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever towards you to switch the headlights back to low beam. Flash-to-Pass Y ou can signal another vehicle by lightly pulling the multifunction lever toward the steering wheel.
contains both driver and passenger reading lights), read- ing lights (located above the rear doors), and a r ear cargo light. Opening a door , pressing the UNLOCK button on the Remote Keyless Entry (RKE) transmitter or turning the center of the multifunction control lever to the extreme up position, will activate all interior courtesy lights.
WINDSHIELD WIPERS AND W ASHERS The front and rear wipers and washers are operated by a switch in the right side control lever . T urn the end of the control lever to select Low , High, or one of the five speed sensitive intermittent windshield wiper speeds.
T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected.
Rain Sensing Wipers — If Equipped This featur e senses moistur e on the windshield and automatically activates the wipers for the driver . The feature is especially useful for r oad splash or overspray from the windshield washers of the vehicle ahead.
operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is gr eater than 32°F (0°C). • T ransmission in NEUTRAL Position — When the ig.
the steering wheel outward or push it inward as desired. T o lock the steering column in position, push the contr ol handle upward until fully engaged. W ARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing.
Press the top of the switch to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF . • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is ON.
T o Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. T o turn the system off, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned off when not in use.
Speed Control without erasing the set speed memory . Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory . T o Resume Speed T o resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 20 mph (32 km/h) for 3.
T o Accelerate For Passing Press the accelerator as you would normally . When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.
The sensors can detect obstacles from approximately 12 to 59 in (30 to 150 cm) from the r ear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.
The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: .
Enable/Disable The Rear Park Assist The Rear Park Assist can be enabled and disabled with a switch located on the upper switch bank of the instru- ment panel. When the switch is pressed to disable the system, the instrument cluster will display the “P ARK ASSIST DIS- ABLED” message.
Cleaning The Rear Park Assist Clean the Rear Park Assist Sensors with water , car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors.
CAUTION! (Continued) • T o avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using the Rear Camera system.
4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙ check entire surroundings ⬙ displayed across the top of the screen. After five seconds this note will disappear . 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.
The lights also turn on when a front door or rear door is opened. The lights will also turn on when the UNLOCK button on the remote keyless entry transmitter is pressed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses.
W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink 威 buttons while keeping the EVIC display in view . For optimal training, point the battery end of the hand- held transmitter away from the HomeLink 威 .
This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer .
Gate Operator/Canadian Programming Canadian radio-fr equency laws requir e transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink 威 to pick up the signal during programming.
Reprogramming A Single HomeLink 姞 Button T o reprogram a channel that has been previously trained, follow these steps: 1. T urn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink 威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.
General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2.
W ARNING! • Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing the sunr oof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed.
Ignition Off Operation The power sunroof switches remain active for up to 10 minutes after the ignition switch has been turned OFF . Opening either front door will cancel this featur e. Sunroof Fully Closed Press the switch forwar d and release to ensur e that the sunroof is fully closed.
W ARNING! T o avoid serious injury or death: • Do not use a three-prong adapter . • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
POWER INVERTER — IF EQUIPPED There is a 1 15-V olt, 150-W att inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 W atts.
Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off. NOTE: • When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON.
CUPHOLDERS In the center console, there are two cupholders for the front seat passengers. The rear passengers have access to two cupholders that pull out from the lower center of the r ear seat.
the car go light lens surface will turn of f all interior lamps. Push on the lens surface a second time to restor e the interior lights to normal operation. Rear Storage Compartment The rear storage compartment is located on the driver’s side behind the second row seat.
W ARNING! In an accident, a loose cargo cover in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting.
Cargo Tie-Down Hooks The tie-downs located on the car go area floor should be used to safely secur e loads when the vehicle is moving. W ARNING! • T o help protect against personal injury , passengers should not be seated in the rear cargo area.
W ARNING! (Continued) • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar . • Always place cargo evenly on the cargo floor . Put heavier objects as low and as far forward as possible.
The car go load floor is held by spring loaded latches. In order to use the cargo load floor , use the following procedur e: NOTE: The cargo load floor latches should not be used as cargo tie-downs. 1. Flip up pull loop(s) so they ar e perpendicular (straight up) to the top surface of the tray .
If the rear wiper is operating when the ignition is turned OFF , the wiper will automatically return to the “Park” position if power accessory delay is active. Power acces- sory delay can be cancelled by opening the door; if this happens, the rear wiper will stop at its current position and will not go to “Park”.
CAUTION! • T o avoid damaging the electrical conductors of the rear window defroster , do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window . • Labels can be peeled of f after soaking with warm water .
NOTE: • T o help control wind noise when the crossbars are not in use, place the front crossbar in the second detent from the fr ont of the vehicle and the rear crossbar in the last detent closest to the rear of the vehicle.
CAUTION! (Continued) • T ravel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. W ind forces, due to natural causes or nearby truck traf fic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features ............... 1 8 1 䡵 Instrument Cluster – Gasoline Engine ....... 1 8 2 䡵 Instrument Cluster – Diesel Engine ......... 1 8 3 䡵 Instrument Cluster Description ...
▫ Notes On Playing MP3/WMA Files ....... 2 1 8 ▫ List Button (Disc Mode For MP3/WMA Play) ......... 2 2 0 ▫ Info Button (Disc Mode For MP3/WMA Play) ............................. 2 2 1 䡵 AM/FM/CD/DVD Radio (RER/REN) – If Equipped ...........
䡵 Universal Consumer Interface (UCI) — If Equipped ............................ 2 4 7 ▫ Connecting The iPod 威 ................. 2 4 8 ▫ Using This Feature ................... 2 4 8 ▫ Controlling The iPod 威 Using Radio Buttons ...........
▫ CD Player ......................... 2 5 9 䡵 CD/DVD Maintenance ................. 2 6 0 䡵 Radio Operation And Cellular Phones ....... 2 6 0 䡵 Climate Controls ...................... 2 6 1 ▫ Manual Air Conditioning And Heating System — If Equipped .
INSTRUMENT P ANEL FEA TURES 1 - Air Outlet 5 - Upper Switch Bank 9 - Lower Switch Bank 2 - Instrument Cluster 6 - Power Outlet/Cigar Lighter 10 - Climate Contr ols 3 - Radio 7 - Storage Bin 1 1 - Igni.
INSTRUMENT CLUSTER – GASOLINE ENGINE 182 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER – DIESEL ENGINE UNDERST ANDING YOUR INSTRUMENT P ANEL 183 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application.
W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have an accident. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
the ON position befor e engine start. If the bulb does not come on when turning the key fr om OFF to ON, have the condition checked promptly . Certain conditions such as a loose or missing gas cap, poor fuel quality , etc. may illuminate the light after engine start.
8. T achometer Indicates the engine speed in revolutions per minute (RPM). 9. V ehicle Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
vehicle placard or tir e inflation pressur e label, you should determine the proper tire inflation pressur e for those tires.) As an added safety featur e, your vehicle has been equipped with a T ire Pressur e Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under -inflated.
tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly . CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
17. 4WD LOW Indicator — If Equipped This light alerts the driver that the vehicle is in the 4WD LOW mode. The front and r ear drive- shafts are mechanically locked together forcing the fr ont and rear wheels to r otate at the same speed.
NOTE: Y ou must apply the brakes before shifting fr om P ARK. 22. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 23. Electronic Throttle Contr ol (ETC) W arning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system.
vehicle is experiencing a pr oblem with the charging system. Obtain SER VICE IMMEDIA TEL Y . See an autho- rized dealer . 26. Low Fuel Light This light will turn on, and a single chime will sound, when the fuel level drops to 1/8 tank.
• V ehicle Information W arning Message Displays • Personal Settings (Customer-Pr ogrammable Features) • Compass Display • Outside T emperature Display • T rip Computer Functions The system .
Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the Electronic V ehicle Information Center (EVIC) displays the following messages: • TURN SIGNAL ON • .
• LIFTGA TE/HOOD OPEN (with graphic) • HOOD/GLASS/DOOR OPEN (with graphic) • HOOD/GLASS/DOORS OPEN (with graphic) • HOOD/GA TE/DOOR OPEN (with graphic) • HOOD/GA TE/DOORS OPEN (with graphic).
• IOD FUSE OUT • HILL DESCENT CONTROL • MEMOR Y #1 POSITIONS SET • MEMOR Y #2 POSITIONS SET • MEMOR Y SYSTEM DISABLED — SEA TBEL T BUCK- LED (with graphic) • MEMOR Y SYSTEM DISABLED — VEHICLE NOT IN P ARK • DRIVER 1 MEMOR Y • DRIVER 2 MEMOR Y • ADJ.
• PRESS BRAKE TO ST AR T • INSER T KEY • TURN TO ON Engine Oil Change Indicator System Oil Change Required (Gasoline Engines Only) Y our vehicle is equipped with an engine oil change indicator system.
• T rip A • T rip B • Elapsed T ime • Service Distance • Display Units of Measure In Press the SCROLL button to cycle through all the T rip Computer functions. The T rip Functions mode displays the following informa- tion: A verage Fuel Economy Shows the average fuel economy since the last reset.
T rip A Shows the total distance traveled for T rip A since the last reset. T rip B Shows the total distance traveled for T rip B since the last reset. Elapsed T ime Shows the total elapsed time of travel since the last r eset when the ignition switch is in the ACC position.
Manual Compass Calibration If the compass appears erratic and the “CAL” indicator does not appear in the EVIC display , you must put the compass into the Calibration Mode manually , as follows: 1. T urn on the ignition switch. 2. Press the MENU button until Personal Settings (Cus- tomer Programmable Featur es) menu is reached.
1. T urn the ignition switch ON. 2. Press the MENU button until Personal Settings (Customer-Pr ogrammable Features) menu is r eached. 3. Press the SCROLL button until “Compass V ariance” is displayed in the EVIC. 4. Press and release the FUNCTION SELECT button to change the variance number .
FUNCTION SELECT button while in this display to select English, Espanol, or Francais. Then, as you con- tinue, the information will display in the selected lan- guage. NOTE: The EVIC will not change the uconnect 威 lan- guage selection. Please r efer to “Language Selection” in the uconnect 威 phone section of this manual for details.
feature may be selected with or without the “Flash Lamps with Lock” feature. T o make your selection, press and r elease the FUNCTION SELECT button until YES (Y) or NO (N) appears. Flash Lamps with Lock When YES (Y) is selected, the front and rear turn signals will flash when the doors ar e locked or unlocked with the RKE transmitter .
NOTE: T urning the headlights on during the daytime causes the instrument panel lights to dim. T o increase the brightness, refer to “Lights” in Section 3 of this manual.
door . Refer to “Easy Entry/Exit Seat” under “Driver Memory Seat” in Section 3 of this manual for more information. Key Off Power Delay When this feature is selected, the power window switches.
• T ire Pressure Monitor System (shows the current pr es- sure of all four road tir es.) For additional information, refer to “T ire Pressur e Monitor System” in Section 5 of this manual. NOTE: • T ires heat up during normal driving conditions.
SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. T o exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry .
SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the r otary TUNE/SCROLL control knob a fifth time and F ADE will display . T urn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and r ear speakers.
Program T ype 16-Digit Character Display Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rh.
• DISC Play/Pause - Y ou can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). • DVD Play Options - Selecting the DVD Play Options will display the fol.
TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer pr eference.
Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie.
Every time a preset button is used, a corresponding button number will display . Button s1-6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
Radio display will show ⬙ LOADING DISC ⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism.
R W/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or R W or another CD button is pressed. The RW (Rewind) button works in a similar manner . AM or FM Button (CD MODE) Switches the radio into the AM or FM radio mode.
Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙ keep disc open after writing ⬙ ar e most likely multisession discs.
ID3 T ag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium.
INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button r epeatedly will scroll through the following T AG information: Song T itle, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙ elapsed time ⬙ priority mode.
TIME Button (Auxiliary Mode) Press the TIME button to change the display fr om elapsed playing time to time of day . The time of day will display for five seconds.
intended for home and other limited viewing uses only , unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. DTS™ ⬙ DTS™ ⬙ and ⬙ DTS™ 2.
T o Manually Set the Clock — RER/REN 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. 3. T ouch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. T o move the hour forward, touch the screen wher e the word “Hour” with the arrow pointing upward is dis- played.
Show T ime if Radio is Off When selected, this featur e will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen where the time is displayed.
SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Pr ess the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Push the rotary TUNE/SCROLL contr ol knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decr ease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display .
SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stor ed into pushbutton memory . The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display .
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display .
Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally .
Supported MP3 File Formats The radio will r ecognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Loading times for playback of MP3 files may be affected by the following: • Media - CD-R W media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to lo.
SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. V oice Recognition System (Radio) — If Equipped Refer to “V oice Recognition System (VR)” in Section 3.
5. T o exit, press any button/knob or wait five seconds. The clock can also be set by pr essing the SETUP button. For vehicles equipped with satellite radio, pr ess the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedur e, starting at Step 2.
SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the r otary TUNE/SCROLL control knob a fifth time and F ADE will display . T urn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and r ear speakers.
Program T ype 16-Digit Character Display Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rh.
AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — T o Set the Pushbutton Memory When you ar e receiving a station that you wish to commit to pushbutton memory , pr ess the SET/RND button. The symbol SET 1 will now show in the display window .
Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (C.
EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF .
SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random or der to provide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected track.
exceeding 20 folders will result in this display . W ith 200 files, exceeding 50 folders will r esult in this display .) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • Level 2: 31 (including a separator ⬙ .
MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title, and album title are supported for version 1 ID3 tags.
begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
Operating Instructions - uconnect 威 phone (If Equipped) Refer to “uconnect 威 phone” in Section 3. Operating Instructions - uconnect 威 studios (Satellite Radio) (If Equipped) Refer to “uconnect 威 studios (Satellite Radio)” in this section.
Connecting The iPod 姞 Use the optional connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles).
Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE contr ol knob to select the next or previous track.
• While a track is playing, press the INFO button to see the associated metadata (Artist, track title, album, etc.) for that track. Pr essing the INFO button again jumps to the next scr een of data for that track. Once you have seen all screens, the last INFO button press will take you back to the play mode screen on the radio.
• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET Buttons are used as shortcuts to the following lists on the iPod 威 .
CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation, or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors.
number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www .siriuscanada.ca for Cana- dian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1.
bikes should be placed as far r earward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structur e or under a physical obstacle.
INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pr essing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display).
SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription.
uconnect studios 姞 (SIRIUS BACKSEA T TV™) — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls ar e located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker -type switch with a pushbutton in the center and controls the volume and mode of the sound system.
Pressing the center button will make the radio switch between the various modes available (AM/FM/T APE/ CD, Etc.). The left-hand contr ol is a r ocker-type switch with a pushbutton in the center . The function of the left-hand control is dif ferent depending on which mode you ar e in.
CD/DVD MAINTENANCE T o keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc.
CLIMA TE CONTROLS Manual Air Conditioning And Heating System — If Equipped The controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort contr ols can be set to obtain desired interior conditions.
Blower Control The blower control rotary knob (on the left) controls the blower and can be set to one of four speeds, and OFF . The blower fan motor will remain on un- til the system is turned to the OFF position or the ignition is turned OFF .
Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. Some airflow is delivered to the floor while in defr ost so that comfort can be maintained.
Recirculation The recirculation feature can be selected with the mode control knob. Y ou may choose be- tween Bi-Level Recirculation and Panel Recir- culation air outlets while in this mode. Nor- mally , air enters fr om outside the vehicle. However , when in “Recirculation” mode air inside the vehicle is r e-used.
NOTE: The numbers on the temperatur e dial represent a comfort setting when the Mode knob is set to AUTO, and not the actual air temperature. T urn the mode control (on the right) knob to AUT O, and then turn the blower contr ol (on the left) knob to either LO AUTO or HI AUT O.
respectively . W ith the temperature setting in these posi- tions, the system does not attempt automatic comfort control. Air Conditioning The air conditioning in this system is automatic. Pressing this button while in AUTO mode will cause the LED to flash three times and remain off.
• Most of the time, when in Automatic operation, you can temporarily put the system into Recir culation mode by pressing the “Recirculation” button. How- ever , under certain conditions in automatic the system is blowing air out of the defr ost vents.
268 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively .
Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor . Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow .
captured interior air to condense on windows and ham- per visibility . For this reason, the system will not allow “Recirculation” mode to be selected while in the defrost or defrost/floor modes. Attempting to use Recirculation while in these modes will cause the LED in the button to blink and then turn off.
When using the air conditioner in extremely heavy traffic, in hot weather , especially when towing a trailer , additional engine cooling may be r equired. If this situa- tion is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed.
Operating Tips Chart UNDERST ANDING YOUR INSTRUMENT P ANEL 273 4 I n f o r m a t i o n P r o v i d e d b y :.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur e ..................... 2 8 0 ▫ Normal Starting ..................... 2 8 0 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ............................ 2 8 1 ▫ If Engine Fails T o Start .
▫ Quadra-T rac II 威 Operating Instructions/Pr ecautions — If Equipped .... 2 9 7 ▫ Shift Positions ...................... 2 9 8 ▫ Shifting Procedur es ................... 2 9 8 ▫ Quadra-Drive II 威 System — If Equipped .... 3 0 1 䡵 On-Road Driving T ips .
▫ HDC (Hill Descent Control) (4WD Models W ith NV245 T wo–Speed T ransfer Case Only) ......................... 3 2 3 ▫ ESP/BAS W arning Light And ESP/TCS Indicator Light ...................... 3 2 5 䡵 T ir e Safety Information ................
䡵 Fuel Requirements ..................... 3 5 5 ▫ 3.7 And 4.7L Engine .................. 3 5 5 ▫ 5.7L Engine ........................ 3 5 5 ▫ Reformulated Gasoline ................ 3 5 6 ▫ Gasoline/Oxygenate Blends ............. 3 5 6 ▫ E-85 Usage In Non-Flex Fuel V ehicles .
䡵 T railer T owing ........................ 3 6 9 ▫ Common T owing Definitions ............ 3 6 9 ▫ T railer Hitch Classification .............. 3 7 2 ▫ T railer T owing W eights (Maximum T railer W eight Ratings) ..................... 3 7 3 ▫ T railer And T railer T ongue W eight .
ST ARTING PROCEDURE Before starting your vehicle, adjust your seat, adjust the inside and outside mirr ors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle.
Extremely Cold Weather (Below ⫺ 20°F or ⫺ 29°C) T o ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is r ecommended.
release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting pr ocedure.
NOTE: • Use of Climatized ULSD Diesel Fuel or Number 1 ULSD Diesel Fuel results in a noticeable decrease in fuel economy . • Climatized ULSD Diesel Fuel is a blend of Number 2 ULSD and Number 1 ULSD Diesel Fuels, which re- duces the temperature at which wax crystals form in fuel.
depending on engine temperatur e. When the “W ait T o Start” goes out, the engine is ready to start. 4. T ip Start Feature Do not pr ess the accelerator . Use the Fob with Integrated Key (FOBIK) to briefly turn the ignition switch to the ST AR T position and then r elease it.
Engine Idling - In Cold W eather A void prolonged idling in ambient temperatures below 0°F (-18°C). Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely . Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles.
• 5.7L Engine — bundled and fastened to the injector harness. • 3.0L Diesel Engine — on the passenger side of the vehicle, mounted on a stud between the fresh airbox and coolant reservoir . W ARNING! Remember to disconnect the cord before driving.
W ARNING! It is dangerous to move the shift lever out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something.
5. Using the scr ewdriver , reach into the manual override opening. Press and hold the shift lock lever down. 6. Move the shift lever into the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. Have your vehicle inspected by your local authorized dealer , if the shift lock manual override has been used.
P ARK This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P ARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever into the P ARK position.
NOTE: T owing the vehicle, coasting, or driving for any other reason with the shift lever in NEUTRAL can result in severe transmission damage. Refer to “Recreational T owing” in Section 5 and “T owing a Disabled V ehicle” in Section 6 of this manual.
transmission will downshift to 4th gear and the display will show 4. Another tap to the left (-) will shift the transmission into 3rd gear . 4.7L and 5.7L Engine On vehicles equipped with 4.7L or 5.7L engines, use of ERS (or TOW/HAUL mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations.
left “D(-)” and hold it ther e. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (5th gear for 3.7L and 3.0L diesel engine, 4th and 5th gears for 4.
OVER TEMP” message may display , and the transmis- sion may downshift out of Over drive until the transmis- sion cools down. After cool down, the transmission will resume normal operation. In high ambient temperatur es with sustained high engine speed and load, an upshift, followed shortly thereafter by a downshift, may occur .
activated. Pressing the switch a second time restor es normal operation. If the TOW/HAUL mode is desired, the switch must be pr essed each time the engine is started. T ransmission Limp Home Mode T ransmission function is monitored for abnormal condi- tions.
drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The feature is operational in Over drive and in DRIVE. NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant ar e warm [usu- ally after 1 to 3 miles (1.
The least amount of accelerator pedal pressure to main- tain the rocking motion, without spinning the wheels or racing the engine, is most effective. Racing the engine or spinning the wheels, due to the frustration of not fr eeing the vehicle, may lead to transmission overheating and failure.
Quadra-T rac II 姞 Operating Instructions/Precautions — If Equipped The Quadra-T rac II 威 transfer case is fully automatic in the normal driving 4WD HI mode. The Quadra-T rac II 威 transfer case pr ovides three mode positions — 4WD HI, NEUTRAL, and 4WD LOW .
Shift Positions For additional information on the appr opriate use of each transfer case mode position, see the information below: 4WD HI All roads surfaces such as ice, snow , gravel, sand, and dry hard pavement. NEUTRAL Disengages both the fr ont and rear driveshafts fr om the powertrain.
4WD LOW to 4WD HI W ith the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into NEUTRAL, and raise the transfer case T -handle. The “4WD LOW” indicator light in the instrument cluster , will flash and go out when the shift is complete.
NEUTRAL Shift Procedure 1. Key ON, engine off. 2. V ehicle stopped, with foot on brake. 3. Place transmission into NEUTRAL. 4. Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink indicating shift in progress.
Quadra-Drive II 姞 System — If Equipped The optional Quadra-Drive II 威 System featur es three torque transfer couplings. The couplings include ELSD (Electronic Limited-Slip Differential) front and rear axles and Quadra-T rac II 威 transfer case.
OFF-ROAD DRIVING TIPS NOTE: Prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with quarter turn fasteners, and can be removed by hand. When T o Use 4WD LOW Range — If Equipped When off-road driving, shift to 4WD LOW for additional traction.
Flowing W ater If the water is swift flowing and rising (as in storm run-of f) avoid cr ossing until the water level recedes and/or the flow rate is reduced. If you must cr oss flowing water avoid depths in excess of 9 in (23 cm). The flowing water can erode the streambed causing your vehicle to sink into deeper water .
Hill Climbing NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4WD LOW . Use first gear and 4WD LOW for very steep hills.
T raction Downhill Shift the transmission into a low gear , and the transfer case into 4WD LOW range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction.
W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. Y ou might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary .
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the proper indicated level.
the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of P ARK. W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury .
wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tir es must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer .
W ARNING! (Continued) • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely , or hydro- planing.
• Do not drive too fast for road conditions, especially when r oads ar e wet or slushy . A wedge of water can build up between the tire tread and the road.
W ARNING! ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ABS cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing.
benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressur e unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated.
NOTE: Anytime the ESP system is in the “Full Off” mode, ERM is disabled. Refer to ESP (Electr onic Stability Program) for a complete explanation of the available ESP modes. W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur .
• Understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ESP/TCS Indicator Light located in the instrument cluster , starts to flash as soon as the tir es lose traction and the ESP system becomes active. The ESP/TCS Indicator Light also flashes when TCS is active.
High Range (4WD Models) or 2WD Models On This is the normal operating mode for ESP in 4WD HIGH range and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD LOW range or NEUTRAL back to 4WD HIGH range, the ESP system will be in this “On” mode.
NOTE: T o improve the vehicle’s traction when driving with snow chains, or starting off in deep snow , sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pr essing the ESP OFF switch.
W ARNING! W ith the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver , the ESP and ERM systems will not engage to assist in maintaining stability . The “Full Off” ESP mode is intended for off-road use only .
W ARNING! W ith the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver , the ESP and ERM systems will not engage to assist in maintaining stability . The “Full Off” mode is intended for off- road use only .
period of time after the driver takes their foot of f of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pr essure and the vehicle will roll down the hill.
W ARNING! • If you use a trailer brake controller with your trailer , your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
HDC (Hill Descent Control) (4WD Models With NV245 T wo–Speed T ransfer Case Only) HDC maintains vehicle speed while descending hills during off-r oad driving situations and is available in 4WD LOW range only . T o enable HDC (transfer case must be in 4WD LOW range), pr ess the HDC switch.
and will only activate when the vehicle is descending a hill. It will usually not activate on level ground. The HDC speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- mission gear selected. • 1st = 1 mph (1.
W ARNING! HDC is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on Eur opean design standards.
• T emporary spar e tires are high-pressure compact spares designed for temporary emergency use only . T ires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- tion. Example: T145/80D18 103M. • High flotation tire sizing is based on U.
EXAMPLE: R = Construction code — ⬙ R ⬙ means radial construction — ⬙ D ⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A num.
EXAMPLE: Load Identification: ⴖ ....blank.... ⴖ = Absence of any text on the sidewall of the tire indicates a Standar d Load (SL) tire Extra Load (XL) = Extra load (or reinfor ced) tire Light Load.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The pr oper cold tire inflation pressure is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard tel.
axles must not be exceeded. For further information on GA WRs, vehicle loading, and trailer towing, refer to “V ehicle Loading” in this section. T o determine the maximum loading conditions of you.
NOTE: • The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
334 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressur es specified on the placard are always cold tire inflation pressure.
loading may be requir ed for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pr essures. W ARNING! High speed driving with your vehicle at or above maximum load is dangerous.
W ARNING! T emporary use spare tires are for emergency use only . W ith these tires, do not drive more than 50 mph (80 km/h). T emporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced.
W ARNING! The limited-use spare tires are for emergency use only . Installation of this limited-use spare tire affects vehicle handling. W ith this tire, do not drive more than 50 mph (80 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly .
These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the indicators appear in two or more adjacent grooves, the tire should be re- placed. Many states have laws r equiring tir e replacement at this point.
Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tir e inflation pressur e.
W ARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings.
TIRE ROT A TION RECOMMENDA TIONS T ires on the front and rear axles of vehicles operate at differ ent loads and perform dif ferent steering, handling, and braking functions. For these reasons, they wear at unequal rates and develop irregular wear patterns.
TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressur e based on the vehicle recommended cold tir e pressur e. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (–1 1°C).
For example, your vehicle has a recommended cold (parked for more than three hours) tire pressur e of 33 psi (227 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a tempera- ture drop to 20°F (-7°C) will decrease the tire pressur e to approximately 24 psi (165 kPa).
NOTE: • The TPMS is not intended to replace normal tire car e and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pr essure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
A tire pr essure monitoring sensor is located in the spare wheel, if the vehicle is equipped with a matching full-size spare wheel and tire assembly . The matching full-size spare tire can be used in place of any of the four road tires.
3. Lots of snow or ice ar ound the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: • If your vehicle is equipped with a matc.
TPM SYSTEM” message will be displayed for 75 sec- onds, and the T ire Pressur e Monitoring T elltale Light will flash on and off for 75 seconds and then r emain on solid.
spare tire can be used in place of any of the four road tires. A low spare tir e will set the “SP ARE LOW PRES- SURE” message, but it will not cause the T ire Pressur e Monitoring T elltale Light to illuminate or the chime to sound.
once the updated tire pr essure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. CHECK TPM SYSTEM W arning The T ire Pressure Monitoring T elltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected.
If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the T ire Pressur e Monitoring T elltale Light will no longer flash, the ⬙ CHECK TPM SYSTEM ⬙ message will not be present, and a pressur e value will be displayed instead of dashes.
show the low tire pressur e value “flashing.” Driving the vehicle for up to 20 minutes above 15 mph (24 km/h) will turn OFF the T ire Pressur e Monitoring T elltale Light as long as none of road tires are below the low pressure warning threshold.
be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to r eceive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
for optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed.
CAUTION! DO NOT use gasoline containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system com- ponents. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer .
blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT . Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
• The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufactur er .
FUEL REQUIREMENTS (DIESEL ENGINES) NOTE: Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maxi- mum) to avoid damage to the emissions control system.
Diesel fuel is seldom completely free of water . T o prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the pr ovided fuel/water separator drain. If you buy good quality fuel and follow the cold weather advice above, fuel conditioners should not be required in your vehicle.
CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of appr oximately 85% fuel ethanol and 15% unleaded gasoline. W ARNING! Ethanol vapors are extremely flammable and could cause serious personal injury .
For best results, a refueling pattern that avoids alternat- ing between E-85 and unleaded gasoline is recom- mended. When you do switch fuel types it is recommended that: • you do not add less than .
consumption. Y ou can expect your MPG and your driv- ing range to decr ease by about 30% compar ed to gasoline operation. Replacement Parts All components in your Flexible Fuel V ehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts.
CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the Malfunction Indica- tor Light (MIL) to illuminate, due to fuel vapors escaping from the system.
W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and will cause the malfunction indicator light to turn on.
CAUTION! Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
Each axle’s GA WR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for in- creased durability , does not necessarily increase the ve- hicle’s GVWR.
the front or rear axles has been exceeded, but the total load is within the specified GVWR. If so, weight must be shifted from front to rear , or r ear to fr ont, as appr opriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally .
Gross T railer W eight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.
some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they are commonly used to tow small- and medium- sized trailers. W eight-Distributing Hitch A weight-distributing hitch system works by applying leverage through spring (load) bars.
T railer Hitch Classification Y our vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional T railer T ow Prep Package.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Model Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.
3.0L Diesel (Limited) 4x2 12,200 lbs (5 534 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 3.0L Diesel (Overland) 4x2 12,250 lbs (5 556 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 3.0L Diesel 4x4 12,250 lbs (5 556 kg) 64 sq ft (5.
T railer And T railer T ongue Weight Always load a trailer with 60% to 65% of the weight in the fr ont of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle.
W ARNING! (Continued) • Improper towing can lead to an injury accident. Follow these guidelines to make your trailer tow- ing as safe as possible: • When hauling cargo or towing a trailer , do not over- load your vehicle or trailer .
T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “T ires – General Information” for pr oper tir e inflation procedur es.
CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances.
The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic T ransmission The DRIVE range can be selected when towing. How- ever , if frequent shifting occurs while in this range, the TOW/HAUL mode (if equipped), or a lower gear range, should be selected.
Cooling System T o reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, shift the trans- mission into NEUTRAL and increase engine idle speed. − Highway Driving Reduce speed.
T owing — Quadra-T rac I 姞 (Single-Speed T ransfer Case) 4WD Models Recreational towing is not allowed. This model does not have a NEUTRAL position in the transfer case. T owing — Quadra–T rac II 姞 /Quadra–Drive II 姞 4WD Models CAUTION! Front or rear wheel lifts should not be used.
Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in pr ogress. The lamp will stop blinking (stay on solid) when the NEUTRAL shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic V ehicle Information Center).
9. Shift the transmission into P ARK. 10. Place the ignition key in the OFF position, and remove key . 1 1. Apply the parking brake. 12. Attach the vehicle to the tow vehicle with tow bar .
Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in pr ogress. The lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL” message will no longer be displayed on the EVIC (Electronic V ehicle Information Center).
NOTE: When shifting out of transfer case NEUTRAL, turning the engine OFF may be required to avoid gear clash. W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
I n f o r m a t i o n P r o v i d e d b y :.
WHA T TO DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................ 3 9 0 䡵 If Y our Engine Overheats ................ 3 9 0 䡵 Jacking And T ire Changing ............... 3 9 1 ▫ Jack Location ....................... 3 9 2 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHERS The Hazard W arning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the Hazard W arning flashers. When the Hazard W arning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer gency .
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned of f until the pointer drops back into the normal range.
Jack Location The scissor-type jack and tire changing tools ar e located in the passenger side compartment, behind the second row seat. Spare Tire Stowage The spar e tir e is stowed under the r ear of the vehicle by means of a cable winch mechanism. T o remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut.
Spare Tire Removal Fit the jack handle extension over the drive nut. Use the lug wrench to r otate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out fr om under the vehicle. CAUTION! • The winch mechanism is designed for use with the jack extension tube only .
W ARNING! Do not attempt to change a tire on the side of the vehicle closest to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into P ARK.
W ARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change.
3. Assemble the jack and jacking tools as shown. Connect jack handle driver (1) to two extensions (2), then to the lug wrench (3). 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed.
5. Raise the vehicle by turning the jack scr ew clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tir e. Minimum tire lift pr ovides maximum stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
wheel nut tightness is 95 ft lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to its fully closed position. W ARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle.
W ARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or cloth- ing. Do not lean over a battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush contami- nated area immediately with large quantities of water .
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the dischar ged battery . Make sur e you have a good contact on the engine.
vehicle. The rear hook will be located on the driver’s side of the vehicle. NOTE: For of f-road recovery , it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road.
I n f o r m a t i o n P r o v i d e d b y :.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L .............. 4 0 6 䡵 Engine Compartment – 4.7L .............. 4 0 7 䡵 Engine Compartment – 5.7L .............. 4 0 8 䡵 Engine Compartment – 3.0L Diesel ......... 4 0 9 䡵 Onboard Diagnostic System — OBD II .
▫ Exhaust System ..................... 4 2 2 ▫ Cooling System ..................... 4 2 4 ▫ Brake System ....................... 4 3 0 ▫ Front/Rear Axle Fluid ................. 4 3 1 ▫ T ransfer Case ....................... 4 3 2 ▫ Automatic T ransmission .
䡵 Fluids And Capacities .................. 4 5 6 䡵 Fluids, Lubricants, And Genuine Parts ....... 4 5 8 ▫ Engine ............................ 4 5 8 ▫ Chassis .
ENGINE COMP ARTMENT – 3.7L 1 — Engine Coolant Reservoir 6 — Battery 2 — Engine Oil Dipstick 7 — W asher Fluid Reservoir 3 — Power Distribution Center 8 — Engine Oil Fill 4 — Brake Flui.
ENGINE COMP ARTMENT – 4.7L 1 — Engine Coolant Reservoir 7 — Battery 2 — Automatic T ransmission Dipstick 8 — W asher Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 — Pow.
ENGINE COMP ARTMENT – 5.7L 1 — Engine Coolant Reservoir 7 — W asher Fluid Reservoir 2 — Automatic T ransmission Dipstick 8 — Engine Oil Dipstick 3 — Power Distribution Center 9 — Engine .
ENGINE COMP ARTMENT – 3.0L DIESEL 1 — Engine Coolant Reservoir 6 — W asher Fluid Reservoir 2 — Power Distribution Center 7 — Engine Oil Fill 3 — Brake Fluid Reservoir 8 — Engine Oil Dips.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
manual). T ighten the gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. The message will remain displayed until the vehicle diagnostic system can retest the fuel system.
Y our vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. T o check if your vehicle’s OBD II system is ready , you must do the following: 1. Insert your ignition key into the ignition switch. 2. T urn the ignition to the ON position, but do not crank or start the engine.
before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. REPLACEMENT P ARTS Use of genuine MOP AR 威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance.
operate satisfactorily without periodic maintenance. However , if a malfunction of these items does occur , it could adversely affect the engine or vehicle performance.
3.0L Diesel Engine Only Anytime the oil is drained and filled it is very important to wait 15 minutes before starting the engine. Engine Oil Selection — Gasoline Engines For best performance and max.
Engine Oil V iscosity (3.7L/4.7L/5.7L Engines) SAE 5W -20 engine oil is recommended for all operating temperatures. This engine oil impr oves low temperature starting and vehicle fuel economy . The engine oil filler cap also shows the r ecommended engine oil viscosity for your vehicle.
The engine oil filler cap also shows the r ecommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, r efer to “Engine Compart- ment” in this section.
W ARNING! The air induction system (air cleaner , hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc.) unless such removal is necessary for repair or maintenance.
W ARNING! (Continued) • Battery posts, terminals and related accessories contain lead and lead compounds. W ash hands after handling. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post, and the negative cable is attached to the negative post.
W ARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. T o avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner to r emove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system.
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
T o minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
accumulation of bugs, leaves, etc. If dirty , clean by gently spraying water fr om a gar den hose vertically down the face of the condenser . Check the engine cooling system hoses for brittle rubber , cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator .
CAUTION! Mixing of engine coolant (antifreeze), other than the specified HOA T engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
• Mix a minimum solution of 50% HOA T engine coolant (antifreeze) and distilled water . Use higher concentra- tions (not to exceed 70%) if temperatur es below -34°F (-37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution.
W ARNING! • The warning words DO NOT OPEN HOT on the cooling system pressure cap are a safety precau- tion. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
of this. As long as the engine operating temperature is satisfactory , the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
• Keep the fr ont of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or W inter operation. If r eplacement is ever necessary , install ONL Y the correct type thermostat.
W ith disc brakes, the fluid level can be expected to fall as the brake linings wear . However , an unexpected dr op in fluid level may be caused by a leak and a system check should be conducted. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
Selection of Lubricant Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for correct fluid type.
Automatic T ransmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for corr ect fluid type.
Fluid Level Check (3.7L and 3.0L Diesel Engine) Regular fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or shift lever malfunction, have your authorized dealer check the transmission fluid level.
2. The vehicle must be on level ground. 3. Fully apply the parking brake, and press the brake pedal. 4. Place the shift lever momentarily in each gear position ending with the lever in P ARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated.
T o prevent dirt and water fr om entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube.
passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. The following maintenance r ecommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.
CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to pr event corrosion. T o remove heavy soil, use MOP AR 威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner .
W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights.
2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOP AR 威 T otal Clean, a mild soap solution, or lukewarm water .
Cav- ity Cartridge Fuse Mini-Fuse Description 3 10 Amp Red Htd Mirror (EBL) 4 20 Amp Y ellow Rr Pwr Out (B+) 5 10 Amp Red Rr HV AC (R/O) (Commander Only) 6 Spare (B+) 7 20 Amp Y ellow Door Locks (B+) .
Cav- ity Cartridge Fuse Mini-Fuse Description 14 20 Amp Y ellow Cigar Ltr (R/A) 15 10 Amp Red T ire Pressur e T ran- sponders (R/O) 16 10 Amp Red Upper & Lower Switch Bank, Diag.
Underhood Fuses (Power Distribution Center) Cav- ity Cartridge Fuse Mini-Fuse Description 1 50 Amp Red PTC Heater 1 (Diesel Only) Cav- ity Cartridge Fuse Mini-Fuse Description 2 40 Amp Green HID Headl.
Cav- ity Cartridge Fuse Mini-Fuse Description 10 — Spare 1 1 40 Amp Green HV AC Blower 12 30 Amp Pink Rear W iper , Ign R/O 13 40 Amp Green Rear W indow De- froster (EBL)/Heated Mirror 14 30 Amp Pin.
Cav- ity Cartridge Fuse Mini-Fuse Description 26 15 Amp Blue Brake Lamps 27 20 Amp Y ellow HD W asher (If Equipped) (Export Only) 28 30 Amp Green ABS V alves 29 20 Amp Y ellow PCM Batt (Gasoline Only).
Cav- ity Cartridge Fuse Mini-Fuse Description 43 25 Amp Natural Coils, Actuators 44 — Spare Underhood Fuses (Integrated Power Module) Cav- ity Cartridge Fuse Mini-Fuse Description 8 10 Amp Red Lt Pa.
Cav- ity Cartridge Fuse Mini-Fuse Description 17 20 Amp Y ellow Rear Fog Lamps (Ex- port Only) 18 20 Amp Y ellow Front Contr ol Module (FCM) Batt #1 19 20 Amp Y ellow Lt T railer-T ow Stop/ T urn 20 2.
air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compr essor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb T ype Glove Box Light .
BULB REPLACEMENT High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself.
Headlight 1. Open the hood. 2. T urn the low or high beam bulb one–quarter turn counterclockwise to r emove from housing. 3. Disconnect the electrical connector and replace the bulb.
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front T urn Signal 1. Open the hood. 2. T urn the turn signal bulb one–quarter turn counter- clockwise to remove fr om housing.
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Light 1. Reach behind the front fascia from under the vehicle.
Rear T ail, Stop, T urn Signal, And Backup Lights 1. Raise the liftgate. 2. Remove the two T orx fasteners. 3. Squeeze the socket assembly tabs to remove it from the housing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, r einstall the socket, and r eattach the light assembly .
Center High-Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. T wist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 3.7/4.7/5.7L Gasoline Engines 21 Gallons 79 Liters 3.0L Diesel Engine 22 Gallons 83 Liters Engine Oil with Filter 3.7 Liter Engine (SAE 5W -20, API Certified) 5 Quarts 4.7 Liters 4.7 Liter Engine (SAE 5W -20, API Certified) 6 Quarts 5.
5.7 Liter Engine (MOP AR 威 Engine Coolant/Antifreeze 5 Y ear/100,000 Mile Formula) — W ith Rear Heat 16.7 Quarts 15.8 Liters 3.0 Liter Diesel Engine (MOP AR 威 Antifreeze/Engine Coolant 5 Y ear/100,000 Mile Formula) — W ithout Rear Heat 13.9 Quarts 13.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil (3.7L/4.7L/5.7L Engines) Use API Certified SAE 5W -20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Component Fluid, Lubricant, or Genuine Part Fuel Selection (3.7L and 4.7L Engine) 87 Octane Fuel Selection (5.7L Engine) 87 Octane Acceptable - 89 Octane Recommended Fuel Selection (3.0L Diesel Engine) Use good quality diesel fuel from a r eputable supplier in your vehicle.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission MOP AR 威 A TF+4 Automatic T ransmission Fluid T ransfer Case (NV140 Single Speed Only) MOP AR 威 A TF+4 Automatic T ransm.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 4 6 2 䡵 Maintenance Schedules ................. 4 6 2 ▫ Maintenance Schedule — Gasoline Engine .
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system.
if it has been 6 months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first.
At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals NOTE: ** V ehicles built with the 4.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or of f-road conditions. Inspect the engine air cleaner filter; replace if necessary .
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the top row of spark plugs (4.7L Engine). ❏ Replace the spark plugs (3.
102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the ignition cables (4.7L Engine). ❏ Replace the side row of spark plugs (4.7L Engine). ❏ Flush and replace the engine coolant if not done at 60 months.
120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the ignition cables (3.7L Engine). ❏ Replace the top row of spark plugs (4.
126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
† This maintenance is recommended by the manufacturer to the owner , but is not required to maintain emissions warranty . W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
• Check the windshield washer solvent and add if requir ed. Once a Month • Check tire pressur e and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of the coolant reservoir , brake master cylinder , and power steering and add as needed.
6,250 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,500 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
18,750 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Rotate tires. ❏ Inspect the front and rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road, or frequent trailer towing.
31,250 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 37,500 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
50,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the fuel filter/water separator unit. ❏ Inspect the front suspension, tie rod ends and boot seals, replace if necessary .
62,500 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary .
75,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the fuel filter/water separator unit. ❏ Inspect the front suspension, tie rod ends and boot seals, replace if necessary .
87,500 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter , replace if necessary .
100,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the fuel filter/water separator unit. ❏ Inspect the front suspension, tie rod ends and boot seals, replace if necessary .
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 8 9 ▫ Prepar e For The Appointment ........... 4 8 9 ▫ Prepar e A List ...................... 4 8 9 ▫ Be Reasonable W ith Requests .
䡵 Publication Order Forms ................ 4 9 3 䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 9 4 ▫ T readwear ......................... 4 9 5 ▫ T raction Grades ..................... 4 9 5 ▫ T emperature Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center .
the ownership experience. Y ou’ll be pleased with their sincere efforts to r esolve any warranty issues or related concerns. W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
T o contact NHTSA, you may either call the Auto Safety Hotline toll fr ee at 1–888–327–4236 (TTY : 1–800–424– 9153), or go to http://www .safercar .gov; or write to: Adminis- trator , NHTSA, 400 Seventh Str eet, SW ., W ashington, D.C. 20590.
• Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-contr olled ve- hicle systems and features.
T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
V ehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum requir ed by law . W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake System) .............. 3 0 9 Adding Fuel ........................... 3 6 4 Adjustable Pedals ....................... 1 4 3 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 417 Air Conditioner Maintenance ............... 4 1 9 Air Conditioning .
T orque Converter ...................... 2 9 4 Autostick ............................. 2 9 0 Auxiliary Electrical Outlet (Power Outlet) ...... 1 6 3 Auxiliary Power Outlet ................... 1 6 3 Battery ............................... 4 1 8 Emergency Starting .
Light ............................... 1 6 7 Luggage Carrier ....................... 1 7 4 Cargo Light ............................ 1 6 7 Cargo Load Floor ........................ 1 7 1 Cargo T ie-Downs ........................ 1 7 0 Cargo (V ehicle Loading) .
Drain, Flush, and Refill .................. 4 2 5 Inspection ........................... 4 2 4 Points to Remember .................... 4 2 9 Pressur e Cap ......................... 4 2 7 Radiator Cap ......................... 4 2 7 Selection of Coolant (Antifreeze) .
Electrical Outlet, Auxiliary (Power Outlet) ...... 1 6 3 Electronic Brake Contr ol System ............. 3 1 2 Anti-Lock Brake System ................. 3 1 2 Brake Assist System .................... 3 1 3 Electronic Roll Mitigation ................ 3 1 4 Electronic Stability Pr ogram .
Overheating .......................... 3 9 0 Starting ............................. 2 8 0 T emperature Gauge .................... 1 8 9 Engine Oil V iscosity ...................... 4 1 6 Engine Oil V iscosity Chart ................. 4 1 6 Enhanced Accident Response Feature .
Fog Lights ....................... 135,192,453 Folding Rear Seat ........................ 1 2 2 Four Wheel Drive ....................... 2 9 6 Operation ........................... 2 9 6 Systems ............................. 2 9 6 Four Wheel Drive Operation .
Gross V ehicle W eight Rating ............. 367,369 GVWR ............................... 3 6 7 Hands-Free Phone (uconnect) ................ 8 2 Hazard W arning Flasher ................... 3 9 0 Head Restraints ......................... 1 1 8 Head Rests .
Interior Appearance Care .................. 4 3 9 Interior Fuses .......................... 4 4 1 Interior Lighting ........................ 1 3 7 Interior Lights ....................... 134,137 Intermittent W ipers (Delay W ipers) ........... 1 4 0 Introduction .
Bulb Replacement ...................... 4 5 0 C a r g o .............................. 1 6 7 Center Mounted Stop ................... 4 5 5 Cruise .............................. 1 9 1 Daytime Running ...................... 1 3 3 Dimmer Switch, Headlight .
T raction Control ....................... 3 2 5 T urn Signal ................ 71,130,136,452,454 V anity Mirror .......................... 8 1 V oltage ............................. 1 9 2 Load Floor , Cargo ....................... 1 7 1 Loading V ehicle .
Mopar Parts ......................... 413,492 Multi-Function Control Lever ............... 1 3 0 New V ehicle Break-In Period ................ 6 8 Occupant Restraints ....................... 3 6 Octane Rating, Gasoline (Fuel) ............ 355,356 Odometer .
Park Sense System, Rear ................... 1 4 7 Parking Brake .......................... 3 0 8 Passing Light ........................... 1 3 7 Pedals, Adjustable ....................... 1 4 3 Personal Settings ........................ 2 0 2 Pets ...
Rear Heated Seats ....................... 1 2 0 Rear Park Sense System ................... 1 4 7 Rear Seat, Folding ....................... 1 2 2 Rear W indow Defroster ................... 1 7 3 Rear W indow Features .................... 1 7 2 Rear W iper/W asher .
Safety Information, T ire ................... 3 2 6 Safety T ips ............................. 6 9 Satellite Radio Antenna ................... 2 5 3 Satellite Radio (uconnect studios) .......... 252,257 Schedule, Maintenance ................. 462,476 Seat Belt Reminder .
Service Manuals ........................ 4 9 3 Setting the Clock ................ 209,223,227,236 Settings, Personal ........................ 2 0 2 Shift Lock Manual Override ................ 2 8 7 Shifting ............................... 2 8 6 Automatic T ransmission .
Sunglasses Storage ....................... 1 5 4 Supplemental Restraint System - Airbag ........ 4 6 Sway Control, T railer ..................... 3 2 0 Synthetic Engine Oil ...................... 4 1 7 System, Remote Starting .................... 2 7 T achometer .
Safety .............................. 3 2 6 Sizes ............................... 3 2 7 Spare T ire ........................... 3 9 2 Spinning ............................ 3 4 0 T read W ear Indicators ................... 3 4 0 Wheel Mounting ........
T ransmitter , Remote Keyless Entry (RKE) ........ 2 1 T read W ear Indicators .................... 3 4 0 T urn Signals ................... 136,185,452,454 UCI Connector ......................... 2 4 7 uconnect (Hands-Free Phone) ................ 8 2 Underhood Fuses .
W indshield Defroster ................ 71,263,269 W indshield W ashers ...................... 1 3 9 Fluid ............................... 4 2 1 W indshield W iper Blades .................. 4 2 1 W indshield W ipers ....................... 1 3 9 W ipers, Intermittent .
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed pr operly by trained person- nel.
GRAND CHER OKEE 2009 ow ner’ s m an u a l 2009 GRAND CHEROKEE Chrysler LL C 81-326-0954 Second Edition Printed in U.S.A. 150920 GrCherokee.indd 1 9/9/08 8:33:17 AM I n f o r m a t i o n P r o v i d .
An important point after buying a device Jeep Grand Cherokee (2009) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jeep Grand Cherokee (2009) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jeep Grand Cherokee (2009) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jeep Grand Cherokee (2009) you will learn all the available features of the product, as well as information on its operation. The information that you get Jeep Grand Cherokee (2009) will certainly help you make a decision on the purchase.
If you already are a holder of Jeep Grand Cherokee (2009), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jeep Grand Cherokee (2009).
However, one of the most important roles played by the user manual is to help in solving problems with Jeep Grand Cherokee (2009). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jeep Grand Cherokee (2009) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
