Instruction/ maintenance manual of the product GE 19209 Jasco
Go to page of 9
GE Model 19209 www.jascoproducts.com Wireless Door Chime Kit Installation Instructions for Battery Operated Wireless Door Chime Kit Required Tools: Small flat blade screwdr iver, drill, drill bit, and phillips screwdriver.
button. 1. Remove the battery from the push button transmitter. 2. Locate the 9 position jumper shown below. 9 position jumper (This pushbutton is set for Ding Dong Chime since 7=off, 8=on, and 9=off.) 3. Select the desired chime sound from the table below.
Parking the jumper on an open set of pins. The two jumpers on the left are in the parked position. Setting The House Security Code Each chime component has jumpers fo r setting the house security code. In most cases you will not need to change the factory settings for the security code.
The chime and pushbutton must be set to the same house security code for the combination to operate together. Note : The push button has 3 additional jum pers that are used to set the chime tune that will play. The chim e tune jumpers do not affect the house security code.
Push Button Jumpers Chime Jumpers 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes. 6. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation.
b. Replacing the back cover 1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor). 2. Before mounting, choose a mounting location that is not farther than 150 feet from the chim e unit location.
3. Use back cover of push button as a template to mark two screw holes. 4. Drill two holes with 3/32” drill in marked locations. 5. Secure back cover to the mountin g surface with two supplied mounting screws. 6. Press front housin g onto back cover.
6. Place the chime unit’s keyhole sl ots over the screw s and press down on the chime unit to secure it. Operation 1. Slide power switch to “O n” to turn on the chime.
Troubleshooting Chime doesn't work: 1. Make sure push button switch is depressed and held for at least 1 second. 2. Make sure plastic tag is removed from battery. 3. Make sure house code switches 1-6 on chime and push button match exactly. 4. Verify battery orientation in push button.
An important point after buying a device Jasco GE 19209 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jasco GE 19209 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jasco GE 19209 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jasco GE 19209 you will learn all the available features of the product, as well as information on its operation. The information that you get Jasco GE 19209 will certainly help you make a decision on the purchase.
If you already are a holder of Jasco GE 19209, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jasco GE 19209.
However, one of the most important roles played by the user manual is to help in solving problems with Jasco GE 19209. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jasco GE 19209 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
