Instruction/ maintenance manual of the product J-SHA Jacuzzi
Go to page of 20
Whirlpool Bath J-SHA ™ II Installation / Operating Instructions.
IMPORT ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SA VE THESE INSTRUCTIONS WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION.
16 Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electri- cal installation according to codes are required for proper installation and user satisfaction. We recom- mend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products.
Specifications _______________________________________________________________________ 1 Framing and Support _________________________________________________________________ 2 Rough-in Reference ____.
J-Sha II Owner's Manual PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 1 Specifications 36" (914 mm) 71-3/4" (1822 mm) 21-1/4" (540 mm) 2 (51 mm) 18" (456 mm) 9-.
J-Sha II Owner's Manual Framing and Support The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior to installing the bath.
J-Sha II Owner's Manual Electrical Connections Two separate circuits are required for this unit: 1. Whirlpool bath controller. 2. Rapid Heat. 1. J-Sha II Install a 120 VAC 20 AMP dedicated circuit protected by a Ground Fault Circuit Interrupter (GFCI).
J-Sha II Owner's Manual 4 Drain Information A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage. A solvent weld type drain is included and must be installed as shown.
J-Sha II Owner's Manual 5 W ater Supply Consult local authorities for plumbing code requirements in your area. IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer.
J-Sha II Owner's Manual 6 WA TER LEVEL SENSOR The bath is equipped with a water level sensor. When the water level is below the sensor, the pump/motor can not be activated. When the water goes above the level sensor, the pump/motor can then be activated.
J-Sha II Owner's Manual 7 80-1 30 1 30-220 11 0 - 15 0 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TO NI C RELAX + + + _ _ _ MIX ON OFF Control Panel ON OFF MIX ON/OFF Button: T urns system on or off. BODY JET Button: T urns the body jets on or off. BACK JET Button: Selects the massage cycle.
J-Sha II Owner's Manual Control Panel Functions 80-1 30 1 30-220 11 0 - 15 0 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ T ONIC RELAX T ONIC/RELAX Button: Select either the T onic or Relax cycle. The LED will light to indicate which cycle is selected.
J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED BACK JETS BUTTON & LED TONIC/RELAX BUTT ON.
J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ T ONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED BODY JETS BUTT ON & LED TIME BUTTON &.
J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED TIME BUTTON & LED SCALE SPEED BUTTON &.
Maintenance Back Jet Manifold Drainage When the unit is turned off, the back jet manifold will continue to drain after the bath is empty Cleaning the J-Sha To clean your J-Sha whirlpool bath, simply use a mild nonabrasive liquid detergent or commercially prepared bathtub cleaner.
13 LIGHT BULB LIGHT BEZEL SHELL BULB RECEPT ACLE LOCKING NUT LIGHT BULB REPLACEMENT Repairs to the Surface Minor scratches which do not penetrate the color finish (acrylic) can be removed with 600-grit wet/dry sandpaper. Restore the glossy finish with an acrylic polish or a comparable automotive paste wax.
14.
WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”).
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
An important point after buying a device Jacuzzi J-SHA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jacuzzi J-SHA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jacuzzi J-SHA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jacuzzi J-SHA you will learn all the available features of the product, as well as information on its operation. The information that you get Jacuzzi J-SHA will certainly help you make a decision on the purchase.
If you already are a holder of Jacuzzi J-SHA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jacuzzi J-SHA.
However, one of the most important roles played by the user manual is to help in solving problems with Jacuzzi J-SHA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jacuzzi J-SHA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
