Instruction/ maintenance manual of the product OCMK01 Invacare
Go to page of 16
On Chair Mounting Kit Assembly , Installation and Operating Instructions Model Nos. OCMK01 and OCMK78 SA VE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage.
2 INSTALLATION OF THE ON CHAIR MOUNTING KIT BACK MOUNTING HARDWARE (FIGURE 1) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2 twist release clamps.
3 Twist Release Clamps. DETAIL "B" Mark FRONT OF WHEELCHAIR Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Upper J Brackets (Top Edge) Lower .
4 INSTALLING THE BACK L BRACKETS (FIGURE 2) NOTE: When mounting the L brackets to the wood backed ContourU cushion the L brackets may be reversed to allow for greater seat depth adjustments as shown in DETAIL A of FIGURE 2.
5 INSTALLING THE BACK J BRACKETS (FIGURE 3) 1. Position the ContourU back between the back canes to determine the approximate mounting position of the J brackets to obtain the desired depth. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 3.
6 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM BACK (FIGURE 4) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 4. 2. Position the two (2) lower J brackets securely into the two (2) fixed release clamps as shown in FIGURE 4.
7 ADJUSTING THE CONTOUR U BACK DEPTH (FIGURE 5) NOTE: There are six (6) depth adjustments avail- able on the ContourU with a pan back. NOTE: There are twelve (12) depth adjustments available on the ContourU with a wood back.
8 ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE (FIGURE 6) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same depth. Refer to ADJUSTING THE CONT OUR U SEA TING SYSTEM BACK DEPTH in this instruction sheet. NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.
9 INSTALLATION OF ON CHAIR MOUNTING KIT SEAT MOUNTING HARDWARE (FIGURE 7) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2) twist release clamps.
10 Twist Release Clamps. DETAIL "B" Mark Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Front J Brackets (Front Edge) Rear J Brackets (Rear E.
11 INSTALLING THE SEAT L BRACKETS (FIGURE 8) NOTE: When mounting the L brackets to the wood backed ContourU seat the L brackets may be reversed to allow for a wider range of seat height adjustments and shown in DETAIL A of FIGURE 8.
12 INSTALLING THE SEAT J BRACKETS (FIGURE 9) 1. Position the ContourU seat between the seat rails to determine the approximate mounting position of the J brackets to ensure the appropriate height setting. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 9.
13 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM SEAT (FIGURE 10) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 10. 2. Position the rear J brackets securely into the fixed release clamps as shown in FIGURE 10.
14 ADJUSTING THE CONTOUR U SEAT HEIGHT (FIGURE 11) NOTE: There are six (6) height adjustments avail- able on the ContourU seat with a seat pan. NOTE: There are twelve (12) height adjustments available on the ContourU seat with a wood back.
15 ADJUSTING THE CONTOUR U SEATING SYSTEM SEAT ANGLE (FIGURE 12) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same height. Refer to ADJUSTING THE CONTOUR U SEAT HEIGHT in this instruction sheet. NOTE: The seat angle is adjusted by repositioning the front and/or the rear J brackets.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. is a trademark of Invacare 800-333-6900 800-668-5324 Corporation.
An important point after buying a device Invacare OCMK01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Invacare OCMK01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Invacare OCMK01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Invacare OCMK01 you will learn all the available features of the product, as well as information on its operation. The information that you get Invacare OCMK01 will certainly help you make a decision on the purchase.
If you already are a holder of Invacare OCMK01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Invacare OCMK01.
However, one of the most important roles played by the user manual is to help in solving problems with Invacare OCMK01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Invacare OCMK01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
