Instruction/ maintenance manual of the product DTR-4.6 Integra
Go to page of 80
DTR-4.6 Instr uction Manual AV Receiv er DTR-4.6.book Page 1 Thursday, September 22, 2005 1:45 PM.
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.
4 Thank you for purchasing an Integra A V Receiv er . Please read this manual thoroughly before making con- nections and plugging in the unit. Follo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiv er .
5 Contents Introduction Important Safety Instructions .................... 2 Precautions ................................................. 3 Supplied Accessories ................................. 4 Features ............................................
6 Features Amplifier • 90 watts per channel into 8 ohms, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating) • 5-channel amplifier • Optimum Gain V olume Circuitry • WRA T (W ide Range Amplifier T echnology) • Massiv e High Current Power Supply (H.
7 Bef ore Using the A V receiver Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
8 Getting to Kno w the A V Receiver For detailed information, see the pages in parentheses. A Standby/On b utton (35) Sets the A V receiver to On or Standby . B Standby indicator (35) Lights up when the A V receiver is on Standby and flashes while a signal is being receiv ed from the remote controller .
9 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. 1 MUTING indicator (50) Flashes while the A V receiver is muted. 2 ZONE 2 indicator (68) Lights up when Zone 2 is on. 3 Listening mode and format indicator s (52) Show the selected listening mode and the format of digital input signals.
10 Getting to Know the A V Receiver —Continued A OPTICAL DIGIT AL These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD players and D VD players. The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder .
11 Getting to Know the A V Receiver —Continued P T APE IN/OUT This analog audio input and output are for connect- ing a recorder with an analog audio input and out- put, such as a cassette deck, MD recorder , etc. Q VIDEO 3 IN A VCR for playback only , or a cable or satellite receiv er can be connected here.
12 Remote Contr oller Including the A V receiver, the remote controller can be used to control up to nine different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the eight Remote Mode buttons.
13 Remote Controller —Continued For detailed information, see the pages in parentheses. A Standby b utton (35) Sets the A V receiver to Standby . B On button (35) T urns on the A V receiv er. C Input Selector buttons (42) Used to select the input sources.
14 Remote Controller —Continued To set the remote controller to D VD mode, pr ess the [D VD] Remote Mode button. A Standby b utton Sets the D VD player to Standby . B On button T urns on the D VD player . C Number buttons Used to enter title, chapter , and track numbers, and to enter times for locating specific points.
15 Remote Controller —Continued To control an Integra CD player or a CD/MD recorder made by another manufactur er , press the [CD] Remote Mode button to select the CD r emote controller mode. To control an Integra MD recorder or CD r ecorder , press the [MD] or [CDR] Remote Mode b utton to select the MD or CDR remote contr oller mode.
16 Remote Controller —Continued HDD mode is for controlling Integra’ s next generation HDD-compatible components. As of 2005, it can be used with the Onkyo DS-A1 Remote Interacti ve Dock and Apple iPod connected via . When Using the Onky o DS-A1: • Connect the DS-A1 to the T APE IN or VIDEO 3 IN jacks.
17 Connecting Y our Speakers Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring DTS and Dolby Digital.
18 Connecting Y our Speakers —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect five speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve.
19 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: • Only connect speakers with an impedance of 6 ohms or higher .
20 Connecting Antenna This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner .
21 Connecting Antenna —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
22 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
23 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver.
24 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or .
25 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a DVD and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or .
26 Connecting Y our Components —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as D VD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel D VD input.
27 Connecting Y our Components —Continued In addition to video playback, with this hookup, you can use your VCR’ s tuner to listen to your favorite TV programs via the A V receiver, useful if your TV has no audio outputs. If you hav e two video recorders (e.
28 Connecting Y our Components —Continued If you hav e two video recorders (e.g., a VCR and a D VD recorder), connect one recorder to the VIDEO 1 OUT jacks, as shown here, and connect the other recorder to the VIDEO 2 OUT jacks in the same way .
29 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the video source and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or .
30 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the CD player and listen in Zone 2. •T o connect the CD player digitally , use connection or .
31 Connecting Y our Components —Continued ■ T urntable with a Built-in Phono Preamp Use an analog audio cable to connect an unused audio input on the A V receiver to the audio outputs on your turntable, as shown.
32 Connecting Y our Components —Continued •W ith connection , you can play and record and listen in Zone 2. •T o connect the recorder digitally for playback, use connections and , or and . •T o connect the recorder digitally for recording, use connection .
33 Connecting Y our Components —Continued W ith (Remote Interactiv e), you can use the following special functions: Auto P o wer On/Standby When you start playback on a component connected via , if the A V receiver is on Standby , it will automatically turn on and select that component as the input source.
34 Connecting Y our Components —Continued The A V receiver has A C outlets on its rear panel that can be used to connect the power cords of other components that you intend to use with the A V receiver. These com- ponents can then be left turned on so that they turn on and off as and when the A V recei ver is turned on and set to Standby .
35 T urning On the A V Receiver Standby/On On Receiver Standby Standby indicator T urning On and Standby Press the [Standby/On] b utton. Alternatively , press the remote contr oller’ s [Receiver] b utton, followed b y the [On] button. The A V receiver comes on, the display lights up, and the Standby indicator goes of f.
36 Fir st Time Setup This section explains the settings that you need to make before using the A V receiver for the v ery first time. This section explains ho w to set the speaker settings. Speaker Configuration Here you can specify which speakers are connected and their individual sizes.
37 First Time Setup —Continued Crosso ver Note: • If the crossov er frequency is set to a lo w value, and the program material doesn’t contain an y sounds below that frequency , the subwoofer will not output much sound.
38 First Time Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button.
39 First Time Setup —Continued If you connect a video component to COMPONENT VIDEO IN 1, 2, or 3, you must assign that input to an input selector . F or example, if you connect your D VD player to COMPONENT IN 3, you must assign COM- PONENT IN 3 to the D VD input selector .
40 First Time Setup —Continued If you connect a component to a digital input, you must assign that input to an input selector . F or example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the CD input selector . Here are the default assignments.
41 First Time Setup —Continued If you connect an -capable Integra MiniDisc recorder , CD recorder , or next generation HDD-compat- ible component to the T APE IN/OUT or VIDEO 3 IN jacks, for to work properly , you must change this setting. This setting can only be changed on the A V receiver.
42 Pla ying Y our A V Components Basic A V Receiver Operation 3 1 3 1 1 1 Use the A V receiver’ s input selector b uttons to select the input source. To select the input source with the remote controller , press the [Receiver] Remote Mode button, and then use the Input Selector b uttons.
43 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations, and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
44 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activ ation fee may apply .
45 Listening to the Radio —Continued Selecting XM Radio Channels There are two modes for selecting XM radio channels: Channel Search mode , which allows you to select an y channel. Category Search mode , which allows you to select channels by category .
46 Listening to the Radio —Continued Selecting XM Channels from the Fr ont Panel: Displaying XM Radio Inf ormation The following information can be displayed: Note: If the category , artist, or song title is not av ailable, “- - -” will be displayed instead.
47 Listening to the Radio —Continued P ositioning the XM Antenna Y ou can check the signal strength of the XM radio signal and adjust the position of the XM antenna accordingly . Note: If the signal quality is 0%, make sure that the XM antenna is connected properly .
48 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM/FM radio stations and XM channels as presets. Selecting Presets Deleting Presets Presetting AM/FM Stations and XM Channels 1 T une into the AM/FM station or XM channel that y ou want to store as a preset.
49 Using the Multichannel D VD Input The multichannel D VD input is for connecting a compo- nent with a 5.1-channel analog audio output, such as a D VD player , D VD-Audio/SA CD-capable player , or an MPEG decoder . See page 26 for hookup information.
50 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiver is set to Standby .
51 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [Sleep] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [Sleep] b utton.
52 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 54. Selecting on the A V Receiver ■ [Stereo] button This button selects the Stereo listening mode.
53 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. Source f ormat Listening mode Analog, PCM *1 *1. In the Direct listening mode, 32 kHz, 44.1 kHz, and 48 kHz PCM is processed at 64 kHz, 88.
54 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction.
55 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the multichannel D VD input cannot be recorded.
56 Onscreen Setup Menus The onscreen setup menus are displayed on the connected TV and pro vide a con venient way to change the A V receiv er’ s settings, which are arranged into two groups: Fi r st T ime Setup and Advanced Setup . To get your system up and running, you must complete the First T ime Setup settings.
57 Adjusting the Listening Modes W ith the Cine Filter function, you can correct a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. This function can be used with the following listening modes: Dolby Digital, Dolby Pro Logic II Movie, DTS, DTS Neo:6 Cinema, DTS 96/24, and Multichannel.
58 Adjusting the Listening Modes —Continued T one Control Settings Y ou can adjust the bass and treble for the front speakers. The tone control circuits are bypassed in the Direct lis- tening mode. ■ Bass Y ou can boost or cut low-frequenc y sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps.
59 Adjusting the Listening Modes —Continued Dolby Digital Settings ■ Late Night W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low v olume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone.
60 Adjusting the Listening Modes —Continued Y ou can specify a default listening mode for each signal format supported by each input selector . The A V receiver will then automatically select that listening mode based on the format of the input signal.
61 Ad v anced Setup This section explains items on the “Input Setup” menu. Delay ■ A/V Sync When using progressiv e scanning, you may find that the picture and sound are out of sync. W ith this setting, you can correct this by delaying the audio signals from 0 to 100 milliseconds (ms) in 1 millisecond steps.
62 Adv anced Setup —Continued This section explains items on the “Preference” menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. IntelliV olume W ith this preference, you can set the input lev el for each input source.
63 Adv anced Setup —Continued ■ Po wer On V ol / Z2 Po wer On V ol W ith these preferences, you can specify the volume set- tings to be used in the main room and Zone 2 when the AV recei ver is turned on. When the V olume Display preference is set to Absolute, the range of “Power On V ol” is 0 to 100 (“Z2 Power On V ol” is 0 to 82).
64 Adv anced Setup —Continued Changing the A V Receiver’ s Remote ID When sev eral Integra components are used in the same room, their remote ID codes may ov erlap. T o differenti- ate the A V receiver from the other components, you can change its remote ID from 1, the default, to 2 or 3.
65 Adv anced Setup —Continued Normally , the A V receiv er detects the signal format auto- matically . Howev er , if you experience either of the fol- lowing issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS: • If the beginnings of tracks from a PCM source are cut off, try the PCM setting.
66 Zone 2 W ith the Zone 2 function, you can enjoy one input source in the main room and a different input source in another room. There ar e two ways to hook up y our Zone 2 speakers: 1) Use another amp (receiv er , integrated amp, or po wer amp) in Zone 2 and connect your Zone 2 speakers to it.
67 Zone 2 —Continued If you’ ve connected your Zone 2 speak ers to this A V receiv er, as explained in “Using Only Speakers in Zone 2” on page 66, you must set the Powered Zone 2 setting to Act (Acti vated) as e xplained here.
68 Zone 2 —Continued This section explains ho w to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2.
69 Zone 2 —Continued Adjusting the V olume for Zone 2 To Mute Zone 2: Press the remote controller’ s [Zone 2] b utton, followed by the [Muting] button. T o unmute Zone 2, press the remote controller’ s [Zone 2] b utton again, followed by the [Muting] button, or adjust the v olume for Zone 2.
70 Zone 2 —Continued When the A V receiver’ s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a con- nected component, you can specify whether or not a 12- volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either .
71 Zone 2 —Continued To control the A V receiver with the remote controller while you’ re in the Zone 2 room, you’ll need a commer - cially av ailable multiroom remote control kit.
72 Contr olling Other Components Y ou can control your other components, including those made by other manufacturers, with the remote controller . This section explains ho w to: • Enter the remote control code for a component that you want to control (e.
73 Controlling Other Components —Continued Remote Control Codes f or Integra Components Connected via Integra components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example.
74 Controlling Other Components —Continued To control another component, point the remote contr oller at it and use the buttons explained below . (Y ou must select the appropriate r emote control mode first.) With some A V components, certain buttons may not work as expected, and some may not work at all.
75 Controlling Other Components —Continued The A V receiver’ s remote controller can receiv e and learn commands from other remote controllers. By trans- mitting, for example, the Play command fro.
76 Controlling Other Components —Continued Y ou can program the remote controller’ s Macro buttons to perform a sequence of actions. Example: To play a CD, you typically need to perform the follow- ing actions: 1. Press the [Receiv er] Remote Mode button to select the Receiv er remote controller mode.
77 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly .
78 Tr oubleshooting —Continued The Zone 2 speakers pr oduce no sound • The Zone 2 speakers only output sources that are con- nected to an analog input. Check to see if the source is connected to an analog input. There’ s no sound with a certain signal format • Check the digital audio output setting on the con- nected device.
79 Tr oubleshooting —Continued The remote controller doesn’t w ork • Make sure that the batteries are installed with the cor - rect polarity (page 7).
80 SN 29344083 (C) Copyright 2005 ONKY O CORPORA TION Japan. All rights reserved. I0509-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.
An important point after buying a device Integra DTR-4.6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Integra DTR-4.6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Integra DTR-4.6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Integra DTR-4.6 you will learn all the available features of the product, as well as information on its operation. The information that you get Integra DTR-4.6 will certainly help you make a decision on the purchase.
If you already are a holder of Integra DTR-4.6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Integra DTR-4.6.
However, one of the most important roles played by the user manual is to help in solving problems with Integra DTR-4.6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Integra DTR-4.6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
