Instruction/ maintenance manual of the product hammer drill Impulse
Go to page of 11
Impulse TM Operating and Maintenance Manual for: Impulse TM Impulse V ision TM Please read all operating instructions before using the Impulse TM p aintball marker . 100 S tation S treet • Loyalhanna, P A 15661 T elephone 724.539.2660 • Fax 724.539.
[ 2 ] It is recommended that you do not dry-fire (fire without paint) your Impulse. The Impulse has a low pressure design, which makes the marker more accurate, and decreases ball breakage. Because of its low pressure design, the marker requires a paintball in front of the bolt to produce back-pressure, which makes the mark- er re-cock.
[ 3 ] Electrical Power Supply The Impulse is powered by a replaceable 9-volt battery . With normal care and usage, the battery should last for approximately 25,000 shots.
Impulse Operating Instructions The following section will review standard operating instructions for activating, deactivating and mode selection for the Impulse. Activating the Impulse T o turn on the Impulse, press and hold the power button for 2 seconds.
[ 5 ] Impulse Adjustment s The following section will review standard adjustment instructions for the Impulse. Vision Eye The new Impulse Vision Eye requires no manual adjustment. All settings are adjusted automatically by the circuit board programming.
[ 7 ] [ 6 ] [893] [885] [885] [893] Power Button (883) Dwell Button Cap (893) Button Housing (885) [883] [Solenoid Housing] [660] V ision Eye Ball Detent [763] Vision Eye Cover [737] Vision Eye Screw .
[ 8 ] [640] S pring Cap [203] Seat Cap [233] O-Ring (09/90) [204] Seat Base [46] O-Ring (10/70) [774] S pring Cap Locking Screw [222] Filter Element [223] Bumper [230] Low Pressure S pring [227] S pri.
[ 9 ] Impulse Maintenance The following section will review standard maintenance instructions for the Impulse. Changing the Battery T o change the battery in the Impulse, remove the two grip cover screws on either side of the grip frame. Remove the old battery and replace with a new 9-volt alkaline battery .
[ 10 ] Cleaning the Vision Eye Remove the Vision Eye ball detent (See p age 6 for V ision Eye Assembly). Gently pull back the Vision Eye cover and remove the V ision Eye screw . Remove the Vision Eye from the Vision Eye slot and wipe with a clean p aper towel or q-tip.
[ 1 1 ] Poor air efficiency - V erify that air system has no leaks. - Increase input pressure from air source and reset dwell to zero. From the lowest dwell setting increase the dwell until the desired velocity is achieved.
100 S tation S treet • Loyalhanna, P A 15661 T elephone 724.539.2660 • Fax 724.539.2298 www .smartpart s.com.
An important point after buying a device Impulse hammer drill (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Impulse hammer drill yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Impulse hammer drill - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Impulse hammer drill you will learn all the available features of the product, as well as information on its operation. The information that you get Impulse hammer drill will certainly help you make a decision on the purchase.
If you already are a holder of Impulse hammer drill, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Impulse hammer drill.
However, one of the most important roles played by the user manual is to help in solving problems with Impulse hammer drill. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Impulse hammer drill along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
