
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301
or visit our website at www.ikea.com
In Canada, call for assistance, installation or service, call: 1-800-807-6777
or visit our website at www.ikea.ca
Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service, composer le 1-800-807-6777
ou visitez notre site web à www.ikea.ca
Table of Contents/Table des matières 2



Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, carbon monoxide, toluene, and soot.

The Anti-Tip Bracket The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the anti-tip bracket fastened down properly.
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip Bracket Making sure the anti-tip bracket is installed:
plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. Do not cut or remove the grounding prong from this plug.
RANGE, THE RANGE MUST BE SECURED BY PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET SECURELY ATTACHED TO FLOOR, AND SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER ANTI-TIP BRACKET.
doors or drawers such as stepping, leaning, or sitting on the doors or drawers.
combustible materials, gasoline, and other flammable vapors and liquids.
heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the oven.
should not be stored in an oven or near surface units.
oven bottom or cover an entire rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard.
not extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
above a range or on the backguard of a range – children climbing on the range to reach items could be seriously injured.
and other utensils. Wipe off all excessive spillage before initiating the cleaning cycle.
grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. In Canada, the range must be electrically grounded in accordance with Canadian Electrical Code. Be sure the range is properly installed and grounded by a qualified technician.

This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The locations and appearances of the features shown here may not match those of your model.

A. Surface burner locator B. Left rear burner control
C. Left front burner control D. Right front burner control
E. Right rear burner control

A. Oven vent B. Surface cooking area C. Anti-tip bracket D. Oven door hinge
F. Storage drawer
J. Automatic oven light switch K. Oven rack
Parts and Features Not Shown Oven light Storage drawer liner (on some models)
(warming drawer on some models) G. Electronic oven control H. Center grate (on some models)
L. Gasket M. Oven door window
E. Model and serial number
N. Self-clean latch O. Gas regulator
plate (behind left side of storage drawer)
I. Surface burner control

Power failure In case of prolonged power failure, the surface burners can be lit manually. Hold a lit match near a burner and turn knob counterclockwise to LITE. After burner lights, turn knob to setting. Do not use the grill or griddle during a power failure. The vent fan will not work.
Sealed Surface Burners
Do not let the burner flame extend beyond the edge of the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death or fire.
Electric igniters automatically light the surface burners when control knobs are turned to LITE. Before setting a control knob, place filled cookware on the grate. Do not operate a burner using empty cookware or without having cookware on the grate.
A. Burner cap B. Burner base C. Alignment pins D. Igniter
To Set: 1. Push in and turn knob counterclockwise to LITE. All 4 surface burners will click. Only the burner with the control knob turned to LITE will produce a flame.
E. Gas tube opening
IMPORTANT: Do not obstruct the flow of combustion and ventilation air around the burner grate edges. Burner cap: Always keep the burner cap in place when using a surface burner. A clean burner cap will help avoid poor ignition and uneven flames. Always clean the burner cap after a spillover and routinely remove and clean the caps according to the “General Cleaning” section. Gas tube opening: Gas must flow freely throughout the gas tube opening for the burner to light properly. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the gas tube opening. Protect it from spillovers by always using a burner cap.
LITE ■ Light the burner.
HI ■ Start food cooking.
MED HI Medium High
MED LO Medium Low
A. 1-1¹⁄₂" (25-38 mm) B. Burner ports
LO ■ Simmer.
Burner ports: Check burner flames occasionally for proper size and shape as shown above. A good flame is blue in color, not yellow. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the burner ports.
REMEMBER: When range is in use or (on some models) during the Self-Cleaning cycle, the entire cooktop area may become hot.
Fire Hazard · MED Medium

To Clean: IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Do not use oven cleaners, bleach or rust removers. 1. Remove the burner cap from the burner base and clean according to “General Cleaning” section. 2. Clean the gas tube opening with a damp cloth. 3. Clean clogged burner ports with a straight pin as shown. Do not enlarge or distort the port. Do not use a wooden toothpick. If the burner needs to be adjusted, contact a trained repair specialist.
Cookware IMPORTANT: Do not leave empty cookware on a hot surface cooking area, element or surface burner. Ideal cookware should have a flat bottom, straight sides and a well-fitting lid, and the material should be of medium-to-heavy thickness. Rough finishes may scratch the cooktop or grates. Aluminum and copper may be used as a core or base in cookware. However, when used as a base they can leave permanent marks on the cooktop or grates. Cookware material is a factor in how quickly and evenly heat is transferred, which affects cooking results. A nonstick finish has the same characteristics as its base material. For example, aluminum cookware with a nonstick finish will take on the properties of aluminum. Cookware with nonstick surfaces should not be used under the broiler. Use the following chart as a guide for cookware material characteristics.
Aluminum ■ Heats quickly and evenly.
Cast iron ■ Heats slowly and evenly.
A. Incorrect B. Correct
Ceramic or Ceramic glass
Home Canning When canning for long periods, alternate the use of surface burners between batches. This allows time for the most recently used areas to cool.
Copper ■ Heats very quickly and evenly.
Earthenware ■ Follow manufacturer’s instructions.
Porcelain enamel-on- steel or cast iron
Stainless steel ■ Heats quickly, but unevenly.

Style 1 - Electronic Oven Controls (on some models)
Start or Start/Enter The Start or Start/Enter pad begins any oven function. If the Start or Start/Enter pad is not pressed within 5 seconds after pressing a function pad, the “START?” indicator light will flash as a reminder. On some models, “START?” will appear on the display. Depending on your model, if Start or Start/Enter is not pressed within 1 minute or 5 minutes after pressing a function pad, the oven display will return to the time of day mode and the programmed function will be canceled.

Cancel or Off/Cancel The Cancel or Off/Cancel pad stops any function except the Clock, Timer and Control Lock.
A. Display B. Timer C. Clock D. Oven light pad (on some
G. Hour/minute (on some
models) H. Timed cooking
I. Temperature J. Auto clean K. Custom broil
models) E. Cancel F. Start (control lock)
Clock This is a 12-hour clock and does not show a.m. and p.m.
L. Bake
Style 2 - Electronic Oven Controls (on some models)
To Set: Before setting, make sure the oven and Timer are off. 1. Press CLOCK. 2. Depending on your model, press the HR or MIN or TIME/ TEMP “up” or “down” arrow pads to set the time of day. 3. Press CLOCK or START.

A. Oven display B. Clock C. Timer/cancel D. Start/enter (control lock)
G. Temperature/time H. Cook time
I. Start time J. Custom broil K. Bake
E. Auto clean F. Off/cancel
Display When power is first supplied to the appliance, “PF” or a flashing time will appear on the display. Press CANCEL or OFF/CANCEL to clear “PF” or flashing time from the display. If “PF” or a flashing time appears, a power failure has occurred. Press CANCEL or OFF/CANCEL and reset the clock if needed. When the oven is not in use, the display shows the time of day. When performing a timed cook function, the display will show either hours and minutes, or minutes and seconds.
Reminder Tones: Reminder tones may be turned off. On some models, press and hold STOP TIME for 5 seconds. “rEP OFF” or “off” will appear in the display. Repeat to turn reminder tones back on, and “rEP on” or “on” will appear in the display. All Tones: All of the above tones are preset on; all except the end-of-cycle tones can be turned off. To Turn Off/On (on some models): Press and hold START TIME for 5 seconds. A tone will sound, and “Snd OFF” will appear on the display. Repeat to turn tones on, and “Snd on” will appear on the display. On some models, only the loudness of the tones can be adjusted. On other models, the tones cannot be adjusted or turned off. Tone Pitch: The pitch is preset at high, but can be changed to low. On some models, only the loudness of the tones can be adjusted. On other models, the tones cannot be adjusted or turned off. To Change (on some models): Press and hold BAKE for 5 seconds. A tone will sound, and “Snd LO” will appear on the display. Repeat to change, and “Snd Hi” will appear on display.

Fahrenheit and Celsius The temperature is preset at Fahrenheit, but can be changed to Celsius. To Change: Press and hold CUSTOM BROIL for 5 seconds. A tone will sound, and “°C” will appear on the display. Repeat to change back to Fahrenheit. To exit mode, press CANCEL or OFF/CANCEL.
Oven Temperature Control IMPORTANT: Do not use a thermometer to measure oven temperature because opening the oven door may cause burner cycling to give incorrect readings. The oven provides accurate temperatures; however, it may cook faster or slower than your previous oven, so the temperature calibration can be adjusted. It can be changed in Fahrenheit or Celsius. A minus sign means the oven will be cooler by the displayed amount. The absence of a sign means the oven will be warmer by the displayed amount. Use the following chart as a guide.
Timer The Timer can be set in hours or minutes up to 12 hours and 59 minutes, and counts down the set time. The Timer does not start or stop the oven.
COOKS FOOD
To Set: 1. Press TIMER SET or TIMER CANCEL*. The timer indicator light will light up on some models. Depending on your model, if no action is taken after 1 minute or 5 minutes, the display will return to the time of day mode. 2. Depending on your model, press the HR or MIN or TIME/ TEMP “up” or “down” arrow pads to set the length of time to cook. 3. Press TIMER SET or START/ENTER. When the set time ends, end-of-cycle tones will sound; then, if enabled, reminder tones will sound every minute on some models. 4. Press TIMER OFF or TIMER CANCEL* anytime to cancel the Timer and reminder tones. Remember, do not press the CANCEL or OFF/CANCEL pad because the oven will turn off.
10°F (5°C) ...a little more
20°F (10°C) ...moderately more
30°F (15°C) ...much more
-10°F (-5°C) ...a little less
-20°F (-10°C) ...moderately less
-30°F (-15°C) ...much less
To Adjust Oven Temperature Calibration: Style 1 - Electronic Oven Controls 1. Press and hold BAKE for 5 seconds until the oven display shows the current calibration, for example “0°F CAL.” 2. Press the TEMP “up” or “down” arrow pad(s) to increase or to decrease the temperature in 10°F (5°C) amounts. The adjustment can be set between 30°F (15°C) and -30°F (-15°C). 3. Press START. Style 2 - Electronic Oven Controls 1. Press and hold BAKE for 5 seconds until the oven display shows the current calibration, for example “00.” 2. Press the TEMP/TIME “up” or “down” arrow pad to increase or to decrease the temperature in 10°F amounts. The adjustment can be set between 30°F and -30°F. NOTE: All temperature adjustments will be displayed in Fahrenheit.
To display the time of day for 5 seconds when the timer is counting down, press CLOCK. *Timer start/Timer cancel keypad.
Control Lock The Control Lock shuts down the control panel pads to avoid unintended use of the oven. When the control is locked, only the clock, oven light (on some models) and timer pads will function. To Lock/Unlock Control: Before locking, make sure the oven and Timer are off. Press and hold START or START/ENTER for 5 seconds. A single tone will sound, and “Loc” will appear on the display. Repeat to unlock. “Loc” will disappear from the display.

Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled. IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well- ventilated room.
BAKEWARE To cook food evenly, hot air must be able to circulate. Allow 2" (5 cm) of space around bakeware and oven walls. Use the following chart as a guide.
POSITION ON RACK
Aluminum Foil IMPORTANT: To avoid permanent damage to the oven bottom finish, do not line the oven bottom with any type of foil, liners or cookware.
1 Center of rack.
2 Side by side or slightly staggered.
3 or 4 Opposite corners on each rack. Make sure that no bakeware piece is directly over another.
Split-Rack with Removable Insert The split-rack with removable insert is a space maximizer. When the two are attached, they make a full rack. The insert can also be removed to provide room for large items such as a turkey and casseroles. Do not place more than 25 lbs (11.3 kg) on the split- rack. The insert can also be used on the counter as a cooling rack.
Positioning Racks and Bakeware IMPORTANT: To avoid permanent damage to the porcelain finish, do not place food or bakeware directly on the oven door or bottom.
A. Split-rack B. Removable insert
If you would like to purchase a split-oven rack, one may be ordered. See “Assistance or Service” section to order. Ask for Part Number 4396927.
To Use Racks: 1. Place a full rack on position 1 or 2, and the split-rack on position 3 or 4. 2. Place large items on the right side of the full rack. 3. Place deeper, covered dishes on the left side of the full rack. 4. Place shallow dishes on the split-rack. 5. When finished cooking, slowly remove items. FOOD RACK POSITION
To move a rack, pull it out to the stop position, raise the front edge, then lift out. Use the following illustration and chart as a guide.
Frozen pies, large roasts, turkeys, angel food cakes
Bundt cakes, most quick breads, yeast breads, casseroles, meats
Cookies, biscuits, muffins, cakes, nonfrozen pies
A. Rear rack section B. Front rack section

Bakeware The bakeware material affects cooking results. Follow manufacturer’s recommendations and use the bakeware size recommended in the recipe. Use the following chart as a guide.
RECOMMENDATIONS
A. Oven vent
The oven vent releases hot air and moisture from the oven, and should not be blocked or covered. Blocking or covering the oven vent will cause poor air circulation, affecting cooking and cleaning results. Do not set plastics, paper or other items that could melt or burn near the oven vent.
Dark aluminum and other bakeware with dark, dull and/or nonstick finish
Baking and Roasting Before baking and roasting, position racks according to the “Positioning Racks and Bakeware” section. When roasting, it is not necessary to wait for the oven preheat conditioning time to end before putting food in unless recommended in the recipe. To Bake or Roast: 1. Press BAKE. 2. Press TEMP or TEMP/TIME “up” or “down” arrow pad to set a temperature other than 350°F (175°C) in 5°F (5°C) amounts. The bake range can be set between 170°F and 500°F (75°C and 260°C). When the oven temperature is greater than 170°F (77°C), no preheat conditioning time will be shown in the display. The preheat conditioning time will not change if the temperature is reset before the countdown time ends.
Insulated cookie sheets or baking pans
Ovenproof glassware, ceramic glass or ceramic
Meat Thermometer On models without a temperature probe, use a meat thermometer to determine doneness of meat, poultry and fish. The internal temperature, not appearance, should be used to determine doneness. A meat thermometer is not supplied with this appliance.
Preheating After the start pad is pressed, the oven will enter a timed preheat conditioning. “PrE” (on some models) and the countdown time will appear on the display. When the preheat conditioning time ends, a tone will sound and the selected temperature will appear on the display. Preheat temperatures are affected by varying factors such as room temperature and peak energy usage times. It is normal for the temperature showing on the display and the actual oven temperature to differ due to the cycling of the elements. Waiting an additional 10 minutes, after the preheat conditioning time ends, to put food in the oven is suggested when baking foods with leavening ingredients, such as yeast, baking powder, baking soda and eggs.
Light colored aluminum · Stainless steel · Stoneware/Baking stone

Broiling and Custom Broiling Broiling uses direct radiant heat to cook food. Changing the temperature when Custom Broiling allows more precise control when cooking. The lower the temperature, the slower the cooking. Thicker cuts and unevenly shaped pieces of meat, fish and poultry may cook better at lower broiling temperatures.
Approximate Time (minutes) SIDE 1 SIDE 2
FOOD
Pork chops 1" (2.5 cm) thick 4 21-22 10-11
Ham slice, precooked ¹₂" (1.25 cm) thick 4 8-10 4-5
Frankfurters 4 6-7 3-4
If you would like to purchase a broiler pan, one may be ordered. See “Assistance or Service” section to order. Ask for Part Number 4396923.
Lamb chops 1" (2.5 cm) thick 4 15-17 8-9
Chicken bone-in pieces boneless breasts
3 4 18-20 12-16 18-20 11-16
Fish Fillets ¹₄-¹₂" (0.6-1.25 cm) thick Fish Steaks ³₄-1" (2-2.5 cm) thick
*Place up to 9 patties, equally spaced, on broiler grid.
Before broiling, position rack according to the Broiling Chart. It is not necessary to preheat the oven before putting food in unless recommended in the recipe. Position food on grid in the broiler pan, then place it in the center of the oven rack. Close the door. To Broil: 1. Press CUSTOM BROIL. 2. Press START or START/ENTER. 3. Press CANCEL or OFF/CANCEL when finished. To Custom Broil: 1. Press CUSTOM BROIL. 2. Press TEMP or TEMP/TIME “up” or “down” arrow pad to change the temperature in 5°F (5°C) amounts. The broil range can be set between 300°F (150°C) and HI (525°F [275°C]). 3. Press START or START/ENTER. If broiling while the timer is counting down, the set broiling temperature can be seen for 5 seconds by pressing CUSTOM BROIL.
Do not let food sit in oven more than one hour before or after cooking.
Doing so can result in food poisoning or sickness.
Timed Cooking allows the oven to be set to cook in 2 different ways. The oven can be set to start cooking immediately and shut off automatically at the end of the cooking time. Or, the oven can be set to start at a later time, cook for a specified length of time and shut off automatically at the end of the cooking time. Foods that require a preheated oven should not be cooked using a delayed function.
BROILING CHART For best results, place food 3" (7 cm) or more from the broil burner. Times are guidelines only and may need to be adjusted for individual tastes. Recommended rack positions are numbered from the bottom (1) to the top (5). For diagram, see the “Positioning Racks and Bakeware” section.
To Set a Timed Cook: 1. Press BAKE (optional). 2. Press the TEMP “up” or “down” arrow pads to enter a temperature other than the one displayed. 3. Press STOP TIME. 4. Press the HR and MIN “up” or “down” arrow pads to enter the desired time to end cooking. 5. Press START. The display will count down the time. When the time ends, the oven will shut off automatically and “End” will appear on the display. End-of-cycle tones will sound; then, if enabled, reminder tones will sound every minute.
Approximate Time (minutes) SIDE 1 SIDE 2
FOOD
Steak 1" (2.5 cm) thick medium rare medium well-done
Ground meat patties* ³⁄₄" (2 cm) thick well-done 4 13-14 6-7
Food Poisoning Hazard · 14-15 15-16 18-19 · 7-8 8-9 9-10

To Set a Delayed Timed Cook: Before setting, make sure the clock is set to the correct time of day. See “Clock” section. 1. Press desired cook function. 2. Press the TEMP “up” or “down” arrow pads to enter a temperature other than the one displayed. 3. Press DELAY START TIME. 4. Press the HR and MIN “up” or “down” arrow pads to enter the time of day to start. 5. Press STOP TIME (optional). 6. If STOP TIME has been pressed, press the HR and MIN “up” or “down” arrow pads to enter the desired time to end cooking. 7. Press START. “DELAY” will appear on the display. When the start time is reached, the oven will automatically turn on. When the stop time is reached (if programmed), the oven will shut off automatically and “End” will appear on the display. End-of-cycle tones will sound, then, if on, reminder tones will sound every minute.
To Set a Delayed Timed Cook: Before setting, make sure the clock is set to the correct time of day. See “Clock” section. 1. Press BAKE. 2. Set the temperature (optional). Press the TEMP/TIME “up” or “down” arrow pad to enter a temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will light up. 4. Press the TEMP/TIME “up” or “down” arrow pad to enter the length of time to cook. 5. Press START TIME. The start time/delay oven indicator light will light up. 6. Press the TEMP/TIME “up” or “down” arrow pad to enter the time of day to start. 7. Press START/ENTER. When the start time is reached, the oven will automatically turn on. The temperature and/or time settings can be changed anytime after pressing START/ENTER by repeating steps 2-7. When the set cook time ends, the oven will shut off automatically and “End” will appear on the display.
To Set a Timed Cook: 1. Press BAKE. The bake indicator light will light up. 2. Set the temperature (optional). 3. Press the TEMP/TIME “up” or “down” arrow pad to enter a temperature other than the one displayed. 4. Press COOK TIME. The cook time oven indicator light will light up.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air must be able to move freely. Depending on your model, see “Oven Vent” or “Oven Vents” section. Do not clean, rub, damage or move the oven door gasket. The door gasket is essential for a good seal.
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the Self-Cleaning cycle. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-ventilated room. Self-clean the oven before it becomes heavily soiled. Heavy soil results in longer cleaning and more smoke. Keep the kitchen well-ventilated during the Self-Cleaning cycle to help get rid of heat, odors, and smoke.
Burn Hazard

ON, HEAT and DOOR LOCKED indicator lights will light up. The door will not unlock until the oven cools.
When the cycle is complete and the oven cools, “End” will appear on the oven display and “LOCKED” shown on the display of some models will disappear. The indicator lights on other models will go off.
How the Cycle Works IMPORTANT: The heating and cooling of porcelain on steel in the oven may result in discoloring, loss of gloss, hairline cracks and popping sounds. The Self-Cleaning cycle uses very high temperatures, burning soil to a powdery ash. The oven is preset for a 3 hour 30 minute clean cycle, but the time can be changed. Suggested clean times are 2 hours 30 minutes for light soil and between 3 hours 30 minutes and 4 hours 30 minutes for average to heavy soil. Once the oven has completely cooled, remove ash with a damp cloth. To avoid breaking the glass, do not apply a cool damp cloth to the inner door glass before it has completely cooled. The oven light will not work during the Self-Cleaning cycle.
To Delay Start Self-Clean (on some models): Before delay starting Self-Clean, make sure the clock is set to the correct time of day. See “Clock” section. Also, make sure the door is closed completely or it will not lock and the cycle will not begin. 1. Press AUTO CLEAN. 2. Press the HR “up” or “down” arrow pad to set a clean time other than 3 hours 30 minutes. The clean time can be set between 3 hours 15 minutes and 5 hours 15 minutes. 3. Press START TIME. 4. Press the HR and MIN “up” or “down” arrows pads to enter the time of day to start. 5. Press START. The time of day is displayed. The door will automatically lock and “LOCKED” and “DELAY” will appear on the display. The door will not unlock until the oven cools. When the start time is reached, the oven will automatically turn on. When the cycle is complete and the oven cools, “End” will appear on the lower oven display and “LOCKED” will disappear.
To Self-Clean: Before self-cleaning, make sure the door is closed completely or it will not lock and the cycle will not begin. 1. Press AUTO CLEAN. 2. Press the HR and MIN “up” or “down” arrow pads, or the TIME/TEMP “up” or “down” arrow pad (depending on your model) to set a clean time other than 3 hours 30 minutes. On models with Style 1 series electronic oven controls (see “Electronic Oven Controls” section), the oven can be set to a clean time between 3 hours 15 minutes and 5 hours 15 minutes.
To Stop Self-Clean anytime: Press CANCEL or OFF. If the oven temperature is too high, “cln,” “TIMED,” “ON,” “cool,” and “LOCKED” will appear on the display (on some models), and the door will remain locked. It will not unlock until the oven cools.
On models with Style 2 series electronic oven controls (see “Electronic Oven Controls” section), the oven can be set to a clean time between 2 hours 30 minutes and 4 hours 30 minutes.
General Cleaning IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Always follow label instructions on cleaning products. Soap, water and a soft cloth or sponge are suggested first unless otherwise noted.
STAINLESS STEEL (on some models)
To avoid damage to stainless steel surfaces, do not use soap- filled scouring pads, abrasive cleaners, Cooktop Polishing Creme, steel-wool pads, gritty washcloths or some paper towels. Rub in direction of grain to avoid damaging. Cleaning Method:
EXTERIOR PORCELAIN ENAMEL SURFACES (on some models)
Food spills containing acids, such as vinegar and tomato, should be cleaned as soon as the entire range is cool. These spills may affect the finish. Cleaning Method:
Rinse with clean water and dry with soft, lint-free cloth.
Gently clean around the model and serial number plate because scrubbing may remove numbers.
METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust removers, ammonia or sodium hydroxide (lye) because paint surface may stain.

OVEN CAVITY
Do not use steel wool, abrasive cleansers or oven cleaner. Do not soak knobs. When replacing knobs, make sure knobs are in the Off position. On some models, do not remove seals under knobs. Cleaning Method:
Do not use oven cleaners. Food spills should be cleaned when oven cools. At high temperatures, foods react with porcelain and staining, etching, pitting or faint white spots can result. Cleaning Method:
Pull knobs straight away from control panel to remove.
CONTROL PANEL
Cleaning Method:
Do not use abrasive cleaners, steel-wool pads, gritty washcloths or some paper towels. Damage may occur. Cleaning Method:
See “Self-Cleaning Cycle” first. Remove racks or they will discolor and become harder to slide. If this happens, a light coating of vegetable oil applied to the rack guides will help them slide.
Apply glass cleaner to soft cloth or sponge, not directly on panel.
BROILER PAN AND GRID (on some models)
Do not clean in the Self-Cleaning cycle. Cleaning Method:
Food spills containing acids, such as vinegar and tomato, should be cleaned as soon as the cooktop, grates and caps are cool. These spills may affect the finish. To avoid chipping, do not bang grates and caps against each other or hard surfaces such as cast iron cookware. Do not reassemble caps on burners while wet. Do not clean in the Self-Cleaning cycle. Cleaning Method:
Scrub with wet scouring pad.
Soak for 20 minutes, then scrub with scouring or steel-wool pad.
Follow product label instructions.
Porcelain enamel only, not chrome
Clean as soon as cooktop, grates and caps are cool.
STORAGE DRAWER (on some models)
Make sure drawer is cool and empty before cleaning. For more information, see “Storage Drawer” section. Cleaning Method:
Use the most aggressive cycle. Cooked-on soils should be soaked or scrubbed before going into a dishwasher.
Drawer Liner (on some models) Remove all stored items from drawer and lift out drawer liner.
See “Sealed Surface Burners” section.
Cleaning Method:
WARMING DRAWER and TRAY (on some models)
Make sure drawer is cool and remove tray. Cleaning Method:

To Replace: 1. Insert both hanger arms into the door.
Oven Light The oven light is a standard 40-watt appliance bulb. It will come on when the oven door is open. When the oven door is closed, press LIGHT to turn it on or off. It will not work during the Self- Cleaning cycle. To replace: 1. Unplug range or disconnect power. 2. Turn the glass bulb cover in the back of the oven counterclockwise to remove.
Storage Drawer The storage drawer can be removed. Before removing, make sure drawer is cool and empty.
Oven Door For normal range use, it is not suggested to remove the oven door. However, if removal is necessary, make sure the oven is off and cool. Then, follow these instructions. The oven door is heavy.
To Remove: 1. Pull the storage drawer straight back past the drawer stop notch and the end of the side rails.
To Remove: 1. Open oven door all the way. 2. Flip up the hinge latch on each side.
A. Drawer stop notch B. End of side rail
To Replace: 1. Lift up the back of the drawer and place it inside the range in its fully forward position. 2. Lift up the front of the drawer to a level position. 3. Slowly push the drawer into the range until the drawer side rails engage with the gap in the drawer glides.

A. Engage drawer glide.

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Surface burner flames are uneven, yellow and/or noisy
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Plug into a grounded 3 prong outlet.
Surface burners will not operate
Electrical Shock Hazard

Oven cooking results not what expected

Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
For further assistance If you need further assistance, you can write to Whirlpool Corporation with any questions or concerns at:
Whirlpool Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692
If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new IKEA® appliance. To locate factory specified parts in your area, call us or your nearest designated service center.
Please include a daytime phone number in your correspondence.
Accessories U.S.A. To order accessories, call the Whirlpool Customer eXperience Center toll free at 1-800-442-9991 and follow the menu prompts. Or visit our website at www.ikea.com and click on “Buy Accessories Online.”
In the U.S.A. Call the Whirlpool Customer eXperience Center toll free: 1-800-253-1301. Our consultants provide assistance with:
In Canada Call the Whirlpool Canada LP Customer Interaction Centre toll free: 1-800-807-6777. Our consultants provide assistance with:
For further assistance If you need further assistance, you can write to Whirlpool Canada LP with any questions or concerns at:
To locate the Whirlpool designated service company in your area, you can also look in your telephone directory Yellow Pages.
Customer Interaction Centre Whirlpool Canada LP 1901 Minnesota Court Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.

ONE YEAR LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company. This limited warranty applies only when the major appliance is used in the country in which it was purchased.
ITEMS WHIRLPOOL WILL NOT PAY FOR 1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair house fuses or to correct house wiring or plumbing. 2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty coverage. 3. Repairs when your major appliance is used for other than normal, single-family household use. 4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool. 5. Any food loss due to refrigerator or freezer product failures. 6. Replacement parts or repair labor costs for units operated outside the United States or Canada. 7. Pickup and delivery. This major appliance is designed to be repaired in the home. 8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance. 9. Expenses for travel and transportation for product service in remote locations. 10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions. 11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was purchased.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another warranty applies. If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 12/05
Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service. Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.