Instruction/ maintenance manual of the product IC-F9511HT Icom
Go to page of 32
INSTR UCTION MANU AL This de vice complies with Part 15 of the FCC Rules. Op - eration is subject to the condition that this device does not cause harmful interference.
i IMPOR T ANT READ ALL INSTRUCTIONS carefully and com - pletely bef ore using the transceiv er . SA VE THIS INSTRUCTION MANU AL — Th is instruction manual contains impor tant oper ating instr uctions f or the IC-F9511HT VHF MOBILE TRANSCEIVER .
ii FCC INFORMA TION • FOR CLASS B UNINTENTIONAL RADIA TORS: This equipment has been tested and f ound to comply with the limits for a Class B digital device , pursuant to par t 15 of the FCC Rules. These limits are designed to pro vide reasonab le protection against har mful interference in a residential instal- lation.
iii R W ARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. R W ARN ING! NEVER co nne ct th e tra nsc eiver t o a power source of more than 16 V DC or use rev erse polar ity . This could cause a fire or damage the transceiv er.
iv T ABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 IMPOR T ANT .......................................................................... i EXPLICIT DEFINITIONS ....................................................... i FCC INFORMA TION .....
1 1 P ANEL DESCRIPTION n Fr ont panel— Controller 01 ch - 0 1 IC-F95 11HT o q e w yr ut i !0 q AF V OLUME CONTROL KNOB Rotate the knob to adjust the audio output le vel. • Minimumaudiolev elispre-programmed. w FUNCTION DISPLA Y (p .
2 1 P ANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 y PO WER SWITCH [PO WER] Push to turn the power ON and OFF . • Thefollowingfunctionsarea vailab leatpowerONasoptions: - Automatic scan start - P assword prompt - Set mode u TRANSMIT INDICA TOR Lights red while transmitting.
3 1 P ANEL DESCRIPTION n Function displa y— Controller 01 c h- 0 1 Ic-F95 11 H T u qw er ty i !0 o q RECEIVED SIGNAL STRENGTH INDICA T OR Indicates relative signal strength le vel. W eak Receive Signal le ve l Strong w LO W PO WER INDICA TOR Appears when low output po wer is selected.
4 1 P ANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 n Pr ogrammable function keys The following functions can be assigned to [UP] , [DO WN] , [P0] , [P1] , [P2] , [P3] and [P4] programmab le function keys . Consult y our Icom dealer or system operator for details con- cerning your transceiv ers programming.
5 1 P ANEL DESCRIPTION PRIO A/B KEYS ➥ Push to select Priority A or Pr iority B channel. ➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] f or 1 sec. to assign the operating channel to the Pr iority A or Prior ity B channel. MR-CH 1/2/3/4 KEYS Push to select the memor y channel 1, 2, 3 or 4.
6 1 P ANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 LIGHT KEY Push to tur n the transceiver’ s backlight ON for about 5 sec. when the backlight function is tur ned OFF in user set mode. (p . 12) HIGH/LO W KEY Push to select the transmit output power temporarily or per- manently , depending on the pre-setting.
7 2 B ASIC OPERA TION n T urning po wer ON When y ou use the transceiver f or the first time, or after the transceiv er has been left unused for a long time, make sure to check th e date and time indic ation afte r turning the power ON. If the time and date are not correct, reset them.
8 2 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 n Receiving and transmitting Receiving: q Push [ ] to turn the power ON. w Push [CH Up] or [CH Down] to select a channel in se - quence. e While receiving a call, adjust the audio output lev el to a comf or table listening le vel.
9 2 BASIC OPERA TION n Cloc k function The transceiver indicates the current time and date when [Clock] is pushed. And y ou can change the indication format and time/date settings.
10 2 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 t Push [Clock] to set. • Thene xtitemblinks. 12HR 03 :00P M YM D0 8- 04-0 1 y Repeat steps e to t to set items. u After setting, push and hold [Cloc k] for 1 sec. to program.
11 2 BASIC OPERA TION t P ush [C H U p] or [C H D own] to in put th e ‘h our ’ da ta for wak e up time. After inputting, push [Clock] to set. • The ‘minutes’ digitblinks. WAKE UP TIME 09:25A M y Push [CH Up] or [CH Down] to input the ‘minutes’ data f or wak e up time.
12 2 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 t Push [CH Up] or [CH Down] to enter the sleep time edit mode. • The ‘hour’ digitblinks. SLEE PT IM E 05:35P M y P ush [C H U p] or [C H D own] to in put th e ‘h our ’ da ta for sleep time.
e Push [P0] sev eral times to select the appropriate item. Then, push [Up] or [Down] to set the desired lev el/condi- tion. • A vailab le set mode functions are Backlight , LCD Contrast , Beep , Beep Level , Ringer Level , SQL Level , AF Min.
14 3 CONNECTION AND MAINTENANCE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 n Separation cable connection CA UTION: T o av oid damage to the transceiv er , disconnect the DC power cab le from the transceiv er before connecting the separation cab le. NO TE: The follo wing connections should be performed by your Icom dealer or distributor .
15 3 CONNECTION AND MAINTENANCE D Main unit q Unscrew the 4 screws of the front plate (either the left or right), then remove the front plate from the main unit.
16 3 CONNECTION AND MAINTENANCE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 + red _ blac k w ANTENNA CONNECT OR Connects to an antenna. Contact y our dealer about an- tenna selection and placement.
n Supplied Accessories KE Y- STICKER Microphone Microphone hanger and screw set Separation cable DC power cab le Ke y caps Housing Function name sti ck ers* 2 * 1 Fuses should be installed in the fuse holder of the blac k and red cables , respectively .
• Function name sticker s There are no names on the programmable function ke ys since the functions can be freely assigned to these ke ys. Attach the supplied function name stick ers as below to the appropriate ke ys for easy recognition of the key’ s assigned function.
D Controller 2 types of mounting styles are availab le— one is ov erhead mounting, and other one is on-board mounting. On-board mounting Bra ck et screw Overhead mounting • Mountthe controller securelywith the 4supplied screwsto a thick surface which can suppor t more than 2 kg (4.
n Antenna A k ey element in the perf or mance of any comm unication sys - tem is an antenna. Contact your dealer about antennas and the best places to mount them. n Fuse installation Fuses should be installed in the fuse holder of the blac k and red cables , respectively .
21 3 CONNECTION AND MAINTENANCE n Speaker connector inf ormation ui o rt y qw e Connector’ s front view Pin No. Name Description Specifications q IGN IGSW cont. In 0 − Vcc w RXSP1 RX AF Out (BTL) Output power : Max. 20 W Impedance : 4 ø e NC — — r HORN1* Horn dr iv e cont.
22 4 OPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 • OPC-607/OPC-608/OPC-609/OPC-726 s e p a r a t i o n c a b l e s Used for a controller and a main unit connection. OPC-607 : 3 m; 9.84 ft OPC-608 : 8 m; 26.3 ft OPC-609 : 1.9 m; 6.3 ft OPC-726 : 5 m; 16.
23 5 SAFETY TRAINING INFORMA TION WA RN IN G Y our Icom radio g enerates RF electroma gnetic en - ergy during transmit mode . This radio is designed for and classified as “Occupational Use Only”, meaning it m ust be used onl y during the course of employment by individuals aware of the hazards, and the wa ys to minimize such hazards.
MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.
MEMO.
MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, J apan A-6718D-1US- w Printed in Japan © 2008−2010 Icom Inc. Printed on recycled paper with soy ink..
An important point after buying a device Icom IC-F9511HT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Icom IC-F9511HT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Icom IC-F9511HT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Icom IC-F9511HT you will learn all the available features of the product, as well as information on its operation. The information that you get Icom IC-F9511HT will certainly help you make a decision on the purchase.
If you already are a holder of Icom IC-F9511HT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Icom IC-F9511HT.
However, one of the most important roles played by the user manual is to help in solving problems with Icom IC-F9511HT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Icom IC-F9511HT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
