Instruction/ maintenance manual of the product IC-F110 Icom
Go to page of 24
iF110 VHF TRANSCEIVER INSTRUCTION MANUAL iF210 UHF TRANSCEIVER IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page a (1,1).
i IMPOR T ANT EXPLICIT DEFINITIONS R W ARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery . This connection will ruin the transceiver .
ii DO NOT use or place the transceiver in areas with tem- peratures below –30°C (–22°F) or above +60°C (+140°F), or in areas subject to direct sunlight, such as the dashboard. A VOID operating the transceiver without running the vehi- cle’s engine.
1 1 P ANEL DESCRIPTION y t r q w e ■ Front panel q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. • Minimum audio level is pre-programmed. w FUNCTION DISPLA Y Displays a variety of information, such as an operating channel number/name, 5-tone code, DTMF numbers and audible condition, etc.
2 1 P ANEL DESCRIPTION t DEALER-PROGRAMMABLE KEYS [P0] to [P3] Desired functions can be programmed independently by your dealer . y MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro- phone for SmarT runk II TM operation here.
3 1 P ANEL DESCRIPTION u 2/5TONE INDICA TOR Appears when the specified 2/5-tone call is received. i ALPHANUMERIC DISPLA Y Displays the CH number , 5-tone indication, DTMF num- bers, Audible indication, etc.
4 1 P ANEL DESCRIPTION ¡ ¡ SCAN ST ART/ST OP KEY Push this key to start scanning; and push again to stop. NOTE: Place the microphone on hook to start scanning. T ake the microphone off hook to stop scanning. ¡ ¡ SCAN T AG KEY Adds or deletes the selected channel to the scan group.
5 1 P ANEL DESCRIPTION ¡ ¡ OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily , or permanently , depending on the pre-setting. • Contact your dealer for the output power level for each selection. ¡ ¡ T ALK AROUND KEY T urns the talk around function ON and OFF .
6 1 P ANEL DESCRIPTION ¡ ¡ SCRAMBLER KEY ➥ Push and hold to turn the voice scrambler func- tion ON. ➥ Push this key to turn the voice scrambler func- tion OFF . NOTE: • The optional UT -109 (#02) or UT -1 10 (#02) VOICE SCRAMBLER UNIT is required.
7 2 OPERA TION ■ T urning power ON q Push [ ] to turn the power ON. w If the transceiver is programmed for a start up passcode, input the digit codes as directed by your dealer . • The keys in the table below can be used for password input: • The transceiver detects numbers in the same block as identical.
8 2 OPERA TION ■ Receiving and transmitting RECEIVING: q Push [ ] to turn the power ON. w Push [] and [] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING: r T ake the microphone off hook.
9 2 OPERA TION D TX code channel selection If the transceiver has a [TX CH] key , the display can be tog- gled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, the [] / [] keys select the TX code channel.
10 2 OPERA TION D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “cus - tomize” transceiver operation to suit your preferences and operating style.
11 3 OPTIONAL SmarT runk II ™ OPERA TION ■ SmarT runk II ™ and conventional modes This transceiver is capable of SmarT runk II™ functions. The optional UT -105 allows communication in conventional channels or SmarT runk II™ channels. Select a channel bank for SmarT runk II™ before trunking operation.
12 3 OPTIONAL SmarT runk II™ OPERA TION D T erminating a call After completing a call, push [#] to disconnect (hang up). IMPORT ANT!: If one person in the conversation termi- nates a call, all participants will be cut off. D Last number re-dial Push [ M ] 2 times to automatically re-dial the last called num- ber .
13 4 CONNECTION AND MAINTENANCE Optional speaker (SP-22) Optional cable (OPC-617) Antenna NEVER connect to a 24 V battery . + red: black: 12V Battery Solder Crimp NOTE: Use the terminals as shown below for the cable connections. R CAUTION! NEVER re - move the fuse-holder from the DC power cable.
14 4 CONNECTION AND MAINTENANCE q ANTENNA CONNECTOR Connects to an antenna. Contact your dealer about an- tenna selection and placement. w MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle ’ s ground for microphone on/off hook functions.
15 4 CONNECTION AND MAINTENANCE ■ Mounting the transceiver The universal mounting bracket supplied with your transceiv- er allows overhead mounting. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.
16 4 CONNECTION AND MAINTENANCE ■ Optional UT -109 or UT -1 10 installation q T urn the power OFF , then disconnect the DC power cable. w Unscrew the 4 cover screws, then remove the bottom cover . e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below .
17 4 CONNECTION AND MAINTENANCE ■ Antenna A key element in the performance of any communication sys- tem is an antenna. Contact your dealer about antennas and the best places to mount them. ■ Fuse replacement A fuse is installed in the supplied DC power cable.
18 5 OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install. Input impedance : 4 Ω Max. input power : 5 W HM-100TN DTMF microphone. SM-25 Desktop microphone. UT -105 SmarT runk II TM Logic Board Provides SmarT runk II TM capabilities. UT -108 DTMF DECODER UNIT Provides pager and code squelch capabilities.
MEMO IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page 19 (1,1).
MEMO IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page 20 (1,1).
Count on us! 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan A-6233H-1EX Printed in Japan © 2002 Icom Inc. IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page Z (1,1).
An important point after buying a device Icom IC-F110 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Icom IC-F110 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Icom IC-F110 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Icom IC-F110 you will learn all the available features of the product, as well as information on its operation. The information that you get Icom IC-F110 will certainly help you make a decision on the purchase.
If you already are a holder of Icom IC-F110, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Icom IC-F110.
However, one of the most important roles played by the user manual is to help in solving problems with Icom IC-F110. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Icom IC-F110 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
