Instruction/ maintenance manual of the product YTH2248 Husqvarna
Go to page of 48
02777 YTH2248 Owner's Manual 01960_husqvarn a.
2 I. GENERAL OPERA TION • Read, understand, and f ollow all instructions in the manual and on the machine bef ore star ting. • Only allow responsib le adults, who are f amiliar with the in struc tions, to operate the machine. • Clear the area of objects such as rocks , toys , wire, etc.
3 • Be sure the area is clear of other people bef ore mowing. Stop machine if any one enters the area. • Nev er carr y passengers or children e ven with the b lades off . • Do not mow in rev erse unless absolutely necessar y . Al ways look down and behind bef ore and while backing.
4 PR ODUCT SPECIFICA TIONS Gasoline Capacity 4 Gallons and type: Unleaded Regular Oil T ype (API-SF-SJ): SAE 10W30 (abov e 32°F) SAE 5W -30 (below 32°F) Oil Capacity: W/ Filter : 4.0 Pints W/O Filter : 3.5 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: 0 – 5.
5 UNASSEMBLED P AR TS Steering Wheel Insert Steering Wheel Steering Wheel Adapter Seat Mower Gauge Wheels (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Adjusting Bars (4) Retainer Springs (double loop.
6 Y our new tractor has been assemb led at the factory with exception of those par ts left unassemb led for shipping purposes. T o ensure saf e and proper operation of your tr actor all par ts and hardware you assemb le must be tightened securely . Use the correct tools as necessar y to insure proper tightness .
7 ASSEMBLE GA UGE WHEELS T O MO WER DECK (See Fig. 5) The gauge wheels are designed to keep the mo wer deck in proper position when operating mow er . Be sure they are prop er ly adjusted to ensure optimum mower per for - mance. • Slide gauge wheel bar down into brac ket channel, Be sure that gauge wheel bar aligning holes are on top .
8 SHOULDER BOL T AD JUST ING BAR PIN RET AINER SPRING FIG. 5 GA UGE WHEEL 3/8-16 CENTER LOCKNUT ASSEMBL Y 3/8 W ASH ER • F or ease of mower to tractor assemb ly , raise gauge wheels to highest position and retain with clevis pins and spring retainers.
9 CHECK TIRE PRESSURE The tires on your tr actor were ov er infl ated at the factory f or shipping pur poses. Correct tire pressure is impor tant f or best cutting performance. • Reduce tire pressure to PSI shown in “PRODUCT SPEC I FI CA TIONS” section of this man ual.
10 These symbols ma y appear on your tractor or in literature supplied with the product. Lear n and understand their mean- ing. OPERA TION DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models.
11 ELAPSED TIME HOURS 1/10 000000000 0 AMPS 60 0 60 02770 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments.
12 OPERA TION 02773 The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age. Al ways wear safety glass es or eye shields while operating y our tractor or per form ing any adjustments or repair s.
13 OPERA TION 02776 LO W POSITION PUSH IN T O "DISENGA GE" AT TAC H MENT LIFT LEVER HIGH POSITION AT TAC H MENT CLUTCH SWITCH PULL OUT T O "ENGA GE" FIG. 10 T O OPERA TE ON HILLS W ARNING: Do not drive up or do wn hills with slopes greater than 15° and do not drive across an y slope .
14 OPERA TION T O ST ART ENGINE (See Fig. 8) When star ting the engine f or the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mov e fuel from the tank to the engine. • Be sure freewheel control is in the transmission en gaged position.
15 OPERA TION MO WING TIPS • Mower should be properly lev eled f or best mowing per- f or mance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mower should be used f or trim- ming.
16 LUBRICA TION CHART BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper.
17 MAINTENANCE TRA CT OR Alwa ys obser v e safety rules when perf or ming an y main- te nance. BRAKE OPERA TION If tractor requires more than six (6) f eet stopping distance at high speed in highest gear , then brak e must be adjusted. (See “TO ADJUST BRAKE” in the Ser vice and Ad just ments section of this manual).
18 MAINTENANCE CLEAN AIR SCREEN Air screen must be k ept free of dir t and chaff to prev ent engine dam age from ov erheating. Clean with a wire br ush or compressed air to re mov e dir t and stubborn dr ied gum fi bers. TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
19 MAINTENANCE IN-LINE FUEL FIL TER (See Fig. 17) The fuel fi lter should be re placed once each season. If fuel fi l ter becomes clogged, ob str uct ing fuel fl ow to car bu re tor , re place ment is re quired. • With engine cool, remov e fi lter and plug fuel line sec- tions.
20 FIG. 18 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress clutc h/brake pedal fully and set parking brake. • Place motion control le ver in neutral (N) position. • Place attachment c lutch in “DISENGA GED” position.
21 SER VICE AND ADJUSTMENTS FIG. 20 FIG. 21 FRONT -T O-BACK ADJUSTMENT (See Figs . 21 and 22) IMPORT ANT : DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLO WING FRONT -T O-BA CK AD JUST MENT IS NECESSARY , BE SURE T O ADJUST BOTH FR ONT LINKS EQU ALL Y SO MO WER WILL ST A Y LEVEL SIDE-T O-SIDE.
22 SER VICE AND ADJUSTMENTS FIG. 23 FIG. 24 T O REPLA CE MO WER BLADE (SEC OND AR Y) DRIVE BEL T (See Fig. 24) P ark the tractor on lev el surface . En gage par king brak e. • Remov e mower (See “T O REMO VE MOWER” in this section of manual). • Remov e screws from R.
23 01513 FIG. 25 SER VICE AND ADJUSTMENTS T O REPLA CE MO TION DRIVE BEL T (See Fig. 26) P ark the tractor on lev el surface . En gage par king br ake. Fo r a s sis tance, there is a belt installation guide decal on bottom side of left f ootrest. BEL T REMO V AL - • Remov e mo wer (See “T O RE MO VE MO WER” in this section of manual).
24 00663 02239 SER VICE AND ADJUSTMENTS FIG. 27 ADJUSTMENT BOL T NEUTRAL LOCK GA TE MO TION CONTROL LEVER TRANSAXLE MO TION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 27) The motion control le ver has been pre set at the factory and adjustment should not be necessar y .
25 SER VICE AND ADJUSTMENTS FIG. 31 02778 HOOD HEADLIGHT WIRE CONNECT OR T O REPLA CE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the bac kside of the grill. • Replace bulb in holder and push b ulb holder securely back into the hole in the bac kside of the grill.
26 SER VICE AND ADJUSTMENTS ENGINE TO A D JUST THR O TTLE CON TROL CABLE The throttle control has been preset at the factory and ad just ment should not be necessar y . If adjustment is nec- es sar y , see engine manual. TO A D JUST CHOKE CON TROL The choke control has been preset at the f actor y and ad- just ment should not be necessar y .
27 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Ne ver store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
28 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” proper ly . 2. Se e “T O ST AR T ENGINE” in Operation section. 3. Engine fl ooded. 3. W ait sever al minutes before attempting to start. 4. Bad spar k plug.
29 TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections . If not when operator leaves seat corrected, contact an authorized ser vice center/ with attachment clutc h depar tment.
30 SER VICE NO TES.
31 TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 SCHEMA TIC BATTERY FUSE RED RED RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK IGNITION UNIT SPARK PLUGS GAP (2 PLUGS ON TWIN CYL.
32 28 29 26 24 42 40 33 30 50 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 ELECTRICAL 12 12 11 10 8 2 1 27 46 89 16 D .
33 KEY P ART NO . NO . DESCRIPTION 1 532 14 49-27 Battery 12 V olt 35 AMP 2 874 76 04-12 Bolt He x Hd 1/4-20 unc x 3/4 8 532 12 48-86 T ray Battery 10 532 14 52-11 Bolt Br t F r t 1/4-20 x 75 Ainc 11 .
34 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 CHASSIS AND ENCLOSURES 10 214 30 277 276 209 31 1 9 55 166 166 209 209 53 280 280 26 144 26 10 209 142 209 142 5.
35 KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U . S. inches. 1 inch = 25.4 mm 1 532 17 46-19 Chassis Stamping 2 532 17 65-54 Dra wbar 9 532 19 02-51 Dash 10 872 14 06-08 .
36 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 DRIVE 29 28 30 52 32 37 53 35 55 36 62 35 36 22 34 16 1 77 77 84 16 263 71 200 73 16 263 199 32 30 52 57 96 26 2.
37 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 DRIVE KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .
38 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 STEERING ASSEMBL Y 5 5 4 3 43 95 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 94 40 11 68 67 67 67 13 65 68 15 15 15 29 29 82 38 12 39 1 41 37 36 37 steering_pl.
39 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 532 16 66-27 Wheel Steering 2 532 18 47-06 Axle Asm 3 532 16 98-40 Spindle Asm LH 4 532 16 98-39 Spindle Asm RH 5 532 12 49-31 Bearing Race Thrust Harden 6 532 12 17-48 W asher 25/32 x 1-5/8 x 16 Ga.
40 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 18 87-15 Seat 2 532 14 05-51 Brac ket Piv ot Seat 8 720 3 871 11 06-16 Bolt Fin He x 3/8-16 x 1 4 819 13 16-10 W asher Flat 13/32 x 1.0 x 10 Ga. 5 532 14 50-06 Clip Push-In 6 873 80 06-00 Nut He x w/Ins.
41 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 DECALS 10 4 3 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO .
42 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 8 10 6 5 116 13 4 26 25 101 3 17 17 17 23 45 14 38 32 31 33 37 33 41 112 engine-ko.
43 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 MO WER LIFT 36 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 50 26 37 41 40 38 49 18 17 16 15 54 54 13 12 11 13 13 31 53 32 32 13 52 49 49 51 51 13 13 20 lift-rh.1pc.
44 REP AIR P AR TS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 MO WER DECK 132 91 94 182 95 183 132 48_nose_roller 57 56 118 116 119 5 117 46 45 33 46 45 33 30 30 32 21 20 18 .
45 REP AIR P ARTS TRA CT OR - MODEL NO . YTH2248 (YTH2248A), PRODUCT NO . 954 57 19-77 MO WER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .S. inches 1 inch = 25.4 mm 1 532 18 03-58 Deck Weldment Mo wer 48 3 532 13 80-17 Brac ket Asm.
46 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
47 SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from t.
532 18 99-07 Re v . 1 6.8.04 RD/MH Printed in U.S .A. 01960_husqvarn a.
An important point after buying a device Husqvarna YTH2248 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna YTH2248 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna YTH2248 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna YTH2248 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna YTH2248 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna YTH2248, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna YTH2248.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna YTH2248. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna YTH2248 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
