Instruction/ maintenance manual of the product YTH2148XP Husqvarna
Go to page of 48
YTH2148XP 02153 Owner's Manual.
2 I. GENERAL OPERA TION • Read, understand, and f ollow all instructions on the machine and in the manual bef ore star ting. • Do not put hands or f eet near rotating par ts or under the machine.
3 • Be sure the area is clear of bystanders bef ore operat- ing. Stop machine if anyone enters the area. • Nev er carr y passengers. • Do not mow in rev erse unless absolutely necessar y . Al wa ys look down and behind bef ore and while back- ing.
4 Gasoline Capacity 4.0 Gallons and type: Unleaded Regular Oil T ype (API-SG-SL): SAE 30 (abov e 32°F) SAE 5W -30 (below 32°F) Oil Capacity: W/ Filter : 3.8 Pints W/O Filter : 3.2 Pints Spark Plug: Champion RCJ8Y (Gap: .030") Ground Speed (MPH): F orward: 0 – 5.
5 UNASSEMBLED P AR TS Mower Gauge Wheels (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Adjusting Bars (4) Retainer Springs (double loop) (4) Clevis Pins (4) Locknuts 3/8-16 (4) Shoulder Bolts Nose Rol.
6 ASSEMBL Y FIG. 1 Y our new tr actor has been assembled at the f actor y with e xception of those par ts left unassembled f or shipping pur- poses. T o ensure safe and proper oper ation of your tractor all par ts and hardware you assemb le must be tightened securely .
7 ASSEMBL Y FIG. 3 02466 02464 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T INST ALL SEA T (See Fig. 3) Adjust seat bef ore tightening adjustment knob. • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor .
8 02510 INST ALL MO WER AND DRIVE BEL T (See Figs. 6 and 7) Be sure tractor is on le vel surf ace and mower suspension ar ms are raised with attachment lift control. Engage park- ing brak e. • Cut and remov e ties secur ing anti-sw ay bar and belts .
9 CHECK TIRE PRESSURE The tires on your tr actor were ov er infl ated at the f actor y f or shipping pur poses. Correct tire pressure is impor tant f or best cutting performance. • Reduce tire pressure to PSI shown in “PRODUCT SPEC I FI CA TIONS” section of this manual.
10 These symbols ma y appear on your tractor or in literature supplied with the product. Lear n and understand their mean- ing. OPERA TION DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models.
11 ELAPSED TIME AMPS 60 0 60 HOURS 1/10 000 0 00 00 00 02527 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments.
12 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age. Always wear saf ety glass es or ey e shields while operating your tractor or per form ing any adjustments or repairs.
13 OPERA TION T O OPERA TE MO WER (See Fig. 10) Y our tractor is equipped with an operator presence sensing s witch. Any attempt b y the operator to leav e the seat with the engine running and the attachment clutch engaged will shut off the engine.
14 OPERA TION T O ST ART ENGINE (See Fig. 7) When star ting the engine for the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mov e fuel from the tank to the engine. • Be sure free wheel control is in the transmission en gaged position.
15 OPERA TION FIG. 12 00272 PURGE TRANSMISSION CA UTION: Ne ver engage or disengage freewheel le ver while the engine is run- ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged bef ore operating tractor f or the fi rst time.
16 BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace .
17 MAINTENANCE TRA CT OR Alwa ys obser ve saf ety rules when performing any main- te nance. BRAKE OPERA TION If tractor requires more than fi ve (5) f eet to stop at highest speed in highest gear on a le vel, dr y concrete or pav ed surf ace, then brak e must be check ed and adjusted, then brak e must be adjusted.
18 MAINTENANCE CLEAN AIR SCREEN Air screen must be k ept free of dir t and chaff to prev ent engine dam age from overheating. Clean with a wire brush or compressed air to re mov e dir t and stubborn dr ied gum fi bers . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
19 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e ver y 100 hours of operation, whiche ver occurs fi rst.
20 02565 SER VICE AND ADJUSTMENTS FIG. 18 T O REMO VE MO WER (See Fig. 18) • Place attachment clutch in “DIS EN GAGED” position. • If equipped, tur n height adjustment knob to low est set ting. • Lower mo wer to its lowest position. • Disengage belt tension rod from lock brac ket.
21 SER VICE AND ADJUSTMENTS MANDREL FIG. 21 FIG. 22 FIG. 20 LIFT LINK ADJUSTMENT NUT 01553 SUSPENSION ARM 02517 BO TH FRONT LINKS MUST BE EQU AL IN LENGTH TRUN NION FRONT PLA TE AS SEM BL Y NUT “C” NUT “D” 02516 FRONT -T O-BACK ADJUSTMENT (See Figs.
22 02515 02513 SER VICE AND ADJUSTMENTS L.H. MANDREL CENTER MANDREL IDLER PULLEY R.H. MAN DREL CO VER SPRING FIG. 24 SEC OND AR Y IDLER ARM SEC OND AR Y SPRING ARM T O REPLA CE MO WER DRIVE BEL T MO WER DRIVE BEL T REMO V AL (See Fig. 23) • P ar k tractor on a le vel surf ace.
23 02537 TRANSMISSION REMO V AL/RE PLA CE MENT Should your tr ansmission require removal f or ser vice or replacement, it should be purged after reinstallation and bef ore operating the tractor . See “PURGE TRANS MIS SION” in the Operation section of this manual.
24 SER VICE AND ADJUSTMENTS FIG. 28 FIG. 27 00 663 RE TA I N ING RING WA S H ERS SQU ARE KEY (REAR WHEEL ONL Y) AXLE CO VER 02614 WEAK OR DEAD BA TTER Y FULL Y CHARGED BA TTER Y T O ST ART ENGINE WITH A WEAK B A T TER Y (See Fig. 28) WA R N I N G : Lead-acid batteries g en- er ate ex plo sive gases.
25 SER VICE AND ADJUSTMENTS FIG. 29 T O REMO VE HOOD AND GRILL ASSEMBL Y (See Fig. 29) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides, tilt to ward engine and lift off of tractor . • T o replace, re verse abo ve procedures .
26 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
27 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST AR T ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes before attempting to start. 4. Bad spar k plug.
28 TR OUBLESHOO TING POINTS Engine continues to run 1. Faulty oper ator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an author ized service center/ with attachment clutc h depar tment.
29 BATTERY FUSE RED RED BLACK BLACK BLACK BLACK BLACK NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BROWN RED ORANGE BROWN M SOLENOID WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
30 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 ELECTRICAL 28 29 26 40 33 30 50 24 42 43 41 27 25 27 22 79 21 45 0 6 0 A M P S 6 0 12 12 11 10 8 2 1 27 55 .
31 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 14 49-27 Batter y 12 V olt 35 AMP 2 874 76 04-12 Bolt Hex H.
32 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 CHASSIS AND ENCLOSURES 64 209 158 74 209 13 1 9 26 144 26 209 209 142 209 142 143 60 17 29 145 161 278 37 37 209 11 209 209 20 59 28 278 278 154 209 278 155 278 209 54 58 54 14 14 38 38 213 214 209 2 10 30 209 31 10 90 159 217 chassis-stealth.
33 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 CHASSIS AND ENCLOSURES 1 532 17 46-19 Chassis Stamping 2 532 17 65-54 Drawbar 9 532 19 58-86 Dash 10 872 14.
34 29 28 30 52 32 37 53 35 55 36 62 35 36 22 34 16 1 77 77 241 32 30 52 57 25 19 24 252 76 78 75 74 27 26 59 19 219 221 221 220 222 221 19 51 51 263 19 19 6 231 239 33 239 238 52 237 233 240 232 241 2.
35 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - T ransaxle Hydro Gear Model 336- 0510 (Order par ts from transaxle manuf acturer) 6 817 06 05-12 Screw 5/16-18 x 3/4 9 532 17 93-34 Clutch Elec 15 874 49 05-44 Bolt Hex Flghd 5/16-18 Gr .
36 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 STEERING ASSEMBL Y 11 5 87 5 87 4 3 43 95 43 8 40 32 8 6 46 46 8 6 2 94 35 34 68 67 67 67 13 65 68 15 29 29.
37 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 532 19 36-51 Wheel Steer ing 2 532 18 47-06 Axle Casting Iron Lt 3 532 16 98-40 Spindle Asm LH 4 532 16 98-39 Spindle Asm RH 5 532 12 49-31 Washer Thrust .
38 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 25 4 23 45 8 6 5 101 13 10 14 38 105 105 3 81 33 37 33 41 1.
39 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 ENGINE NO TE: All component dimensions given in U .S. inches 1 inch = 25.
40 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 SEA T ASSEMBL Y KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532 18 87-15 Seat 2 532 14 05-51 Brack et Pivot Seat 8 720 3 871 11 06-16 Bolt Fin Hex 3/8-16 x 1 4 819 13 16-10 Washer Flat 13/32 x 1.
41 1 3 3 9 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532 05 91-92 Cap V alve Tire 2 532 06 51-39 Stem V alve 3 532 10 62-22 Tire F Ts 15 x 6.
42 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 MO WER LIFT 36 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 50 26 37 41 40 38 49 18 17 16 15 54 54 13 12 11 13 13 31 53 32 32 13 52 49 49 51 51 13 13 20 lift-rh.
43 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 MO WER LIFT 1 532 15 94-61 Wire Asm Inner/Spr ing W/Plunger L T 2 532 15 94-76 Shaft Asm Lift RH w/Inf 3 532 18 88-22 Pin Groove 4 812 00 00-02 E Ring #5133-62 5 819 21 16-21 Washer 21/32 x 1 x 21 Ga.
44 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 MO WER DECK 90 91 94 180 180 182 95 183 90 48_nose_roller _1 57 56 118 116 119 5 117 46 45 33 46 45 33 30 3.
45 REP AIR P ARTS TRA CT OR - MODEL NUMBER YTH2148XP (HA U21H48B), PRODUCT NO . 954 17 02-27 MO WER DECK 1 532 18 18-48 Deck Weldment Mo wer 48 3 532 13 80-17 Brack et Asm., Sway Bar 5 532 12 46-70 Retainer Spr ing 6 532 17 80-24 Sway Bar Dec k 8 532 17 43-65 Bolt, 7/16 Asm.
46 SECTI ON 1: LIMITED WA R RANTY Husqvar na F orest & Garden Compa ny (“Husqv arna”) warrants Husqv ar na product to the original pur- chaser to be free from defects in material and w orkmans.
47 15 DEGREES MAX. F O L D A L O N G D O T T E D L IN E T H IS IS A 15 D E G R E E S L O P E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
532 19 57-68 Re v . 1 12.13.04 TR Printed in U.S .A. 01960_husqvarn a.
An important point after buying a device Husqvarna YTH2148XP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna YTH2148XP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna YTH2148XP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna YTH2148XP you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna YTH2148XP will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna YTH2148XP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna YTH2148XP.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna YTH2148XP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna YTH2148XP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
