Instruction/ maintenance manual of the product YTH130 Husqvarna
Go to page of 72
YTH130 Manuel d’instructions Merci de lire trés attentivement le manuel d'instructions. Assurez-vous d'avior tout compris avant d'utiliser ce tracteur. Manual de las instrucciones Por favor lea cuidadosamente y comprenda estas intrucciones antes de usar esta maquina.
2 3 18 27 37 39 49 68 71 Safety rules. Reglas de seguridad. Sicherheitsvorschriften. Norme antinfortunistiche. Règles de sécurité. Ve iligheidsregels. Assembly. Montaje. Zusammenbau. Montaggio. Montage. Montering. Functional description. Descripción del funcionamiento.
3 1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I .
4 IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. • Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark. • Allow the engine to cool before storing in any enclo- sure.
5 • Bei Maschinen mit mehreren M ä hmessern ist Vorsicht geboten, da beim Drehen eines M ä hmessers die anderen M ä hmesser sich wom ö glich mit drehen. III. Betrieb • Maschine nicht in einem geschlossenen Bereich betreiben, in dem die gef ä hrlichen Kohlenmoxydgase sich sammeln k ö nnen.
6 • Alle Anbauger ä te-Antriebe ausschalten, den Motor abstellen und das (die) Z ü ndkerzenkabel abziehen bzw. den Z ü ndschl ü ssel abziehen: - vor dem Entfernen von Verstopfungen aus dem M ä hwerk oder dem Auswurf; - vor dem Pr ü fen, Reinigen oder Reparieren des Rasenm ä hers; - nachdem auf ein Fremdk ö rper gesto ß en wurde.
7 III. Utilisation • Ne d é marrez jamais le moteur à l'int é rieur d'un b â timent o ù des vapeurs dangereuses de monoxyde de carbone pourraient s' ê tre accumul é es. • Tondez uniquement à la lumi é re du jour ou avec une bonne lumi è re artificielle.
8 • D ´ ebrayez les lames, arr ê tez le moteur, et d é branchez le (s) fil (s) de la bougie d'allumage ou enlevez la clef de contact: - avant de retirer l'insert broyeur ou avant de retirer la goulotte d' é jection pour la nettoyer.
9 1. Reglas De Seguridad Pr á cticas de Operaci ó n Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
10 • Desenganche la transmisi ó n a los accesorios, pare el motor, y desconecte el (los) cable (s) de la buj í a o remueva la llave de ignici ó n - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - despu é s de golpear un objeto extra ñ o.
11 I . Addestramento All 'Uso • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l ’ uso corretto dell ’ equipaggiamento. • Non consentire mai l ’ uso dei trattorini tosaerba ai bambini n é agli adulti che non abbiano dimestichezza con le istruzioni sull ’ uso.
12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e .
13 I . Training • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken. Het is mogelijk dat plaatselijke voorschriften een beperking stellen aan de leeftijd van de bestuurder.
14 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
15 BATTERY BATTERIE BATTERIE ACCU BATER Í A BATTERIA CAUTION VORSICHT ATTENTION OPGELET PRECAUCI Ó N ATTENZIONE BEWARE OF THROWN OBJECTS VORSICHT, HOCHGESCHLEUDERT GEGENST Ä NDE FAITES ATTENTION AU.
16 NO OPERATION ON SLOPES MORE THAN 10 NICHT AUF ABH Ä NGEN MIT MEHR ALS 10 STEIGUNG BETREIBEN N'UTILISEZ JAMAIS SUR DES PENTES DE PLUS DE 10 NIET OP HELLINGEN VAN MEER DAN 10 GEBRUIKEN NO OPERE.
17 SHIELD EYES. EXPLOSIVE GASES CAN CAUSE BLINDNESS OR INJURY. SULFURIC ACID CAN CAUSE BLINDNESS OR SEVERE BURNS. FLUSH EYES IMMEDIATELY WITH WATER. GET MEDICAL HELP FAST. PROT GER LES YEUX. GAZ EXPLOSIFS, PEUVENT RENDRE AVEUGLE OU PROVOQUER DES L SIONS.
18 2. Assembly . 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Eng D F Esp I NL Eng D Before the tractor can be used certain parts must be as- sembled, which for transportation reasons are enclosed in the packing. The picture shows which parts must be as- sembled.
19 F Esp I NL 1 VOLANT DE DIRECTION • Monter la rallonge d ’ arbre de direction sur les orifices souhait é s puis installer la vis hexagonale et l ’é crou frein, bien serrer le tout, • Positionner le cache sur la colonne de direction.
20 Seat Remove the hardware securing seat to the cardboard pack- ing and set the hardware aside for assembly of seat to tractor. Pivot seat upward and remove from cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
21 3 D Eng F Esp I NL NOTE! Check that the flex is correctly connected to the safety switch (3) on the seat holder. HINWEIS! Pr ü fen, da ß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist.
22 1. Seat pan 2. Battery box door 3. Cable 4. Cable A. Front of tractor 5. Fender 6. Battery terminal 7. Battery 1. Sitzwanne 2. Batteriekasten ö ffnung 3. Kabel 4. Kabel A. Vorderseite des Rasenm ä hers 5. Schutzblech 6. Batteriepol 7. Batterie 1.
23 5 7 A 6 1 2 3 4 1. Asiento 2. Tapa de la caja de bateria 3. Cable 4. Cable A. Frontal de tractor 5. Protecci ó n 6. Terminal de bater í a 7. Bater í a 1. Vando sedile 2. Sportello vano batteria 3. Cavo 4. Cavo A. Lato anteriore del trattore 5. Paraurti 6.
24 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion.
25 Eng TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con- ditions.
26 PARA AJUSTAR LAS RUEDAS CALIBRADORAS Las ruedas calibradoras est á n bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora est é a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posici ó n para prevenir el corte raspeo en casi todos los terrenos.
27 9 Eng D 6 1 7 3 2 5 8 4 Positioning of controls 1. Light Switch. 2. Throttle/Choke Control. 3. Brake and clutch pedal. 4. Motion control lever. 5. Connection/disconnection of the cutting unit. 6. Quick lifting/lower of the cutting unit. 7. Ignition lock.
28 I F Esp NL 9 6 1 3 2 5 8 4 7 Comandi 1. Interruttore luci. 2. Comando gas/choke. 3. Pedale freno/frizione. 4. Leva del cambio. 5. Inserimento/disinserimento del dispositivo di taglio. 6. Sollevamento/abbassamento del tagliaerba. 7. Chiave di accensione.
29 1. Light switch 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting Eng F D Esp I NL 2. Throttle and choke control The accelerator control regulates the motor speed and also the speed of the blades.
30 Eng NL I Esp F D 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorw ä rtsdr ü cken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
31 F R N S 4. Motion control lever There are four different positions for this lever: N = Neutral (no drive) S = Slow F = Fast R = Reverse The lever can be moved steplessly between S and F to ensure the required speed.
32 Eng D F Esp NL I 5. Connection/disconnection of the cutting unit Move the lever forward to connect the drive to the cutting unit, whereby the drive belt is tensioned and the blades begin to rotate.
33 D Eng F Esp I NL 1 3 2 6. Quick lifting/lowering of the cutting unit Pull the lever backward to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During transporta- tion the cutting unit shall be in the highest position.
34 Eng D OFF ON START Eng D I F Esp NL 7. Ignition Lock There are three different positions for the ignition key: O F F All electric current broken. ON Electric current connected. START Start motor connected. WARNING! Never leave the key in the ignition lock when leaving the machine on its own.
35 F Esp NL I 8. Frein de parking Pour enclencher le frein de parking : 1. Enfoncer à fond la p é dale de frein/embrayage. 2. En m ê me temps, relever vers le haut le levier du frein de parking et le maintenir dans cette position. 3. Rel â cher la p é dale de frein.
36 Eng D F NL I Esp 9. Free-wheel Control Lever To tow or move the tractor without the aid of the engine, the free-wheel control knob must be pulled out and locked in position. 9. Ein-und Ausschalten des Freilaufes Um den Traktor ohne Motorkraft abzuschleppen oder anzuschieben, mu ß der Freilauf-Steuerungsknopf herausgezogen.
37 4 4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarr er . 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Eng D F I Esp NL Reposición de combustible El motor ha de funcionar con gasolina pura (sin mezcia de aceite), sin plomo.
38 4 D Eng F NL Esp I D F Esp I NL ADD FULL CAUTION - DO Eng Livello dell ’ olio Sollevare il cofano per accedere al tappo/asticella dell ’ olio. Controllare sempre l ’ olio prima di avviare il motore. La macchina deve essere in piano. Svitare l ’ asticella e asciugarla.
39 5 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. D é marrage du moteur S ’ assurer que le carte de coupe est en position de transport (en position sup é rieure) et que le levier pour l ’ embrayage/ d é brayage du carte de coupe est en position de d é brayage.
40 5 NL I Esp F D Eng Warm motor: Push the gas control half-way to full gass position " ". Bei warmem Motor: Gashebel in die Vollgasstellung " " schieben. Avec un moteur chaud: pousser l'acc é l é rateur à mi-chemin vers la position d'acc é l é rateur maximale " ".
41 5 Turn the ignition key to “ START position ” . NOTE! Do not run the start motor more than 5 seconds at once. If the engine will not start, wait about 10 seconds before the next try. Z ü ndschl ü ssel auf “ START ” drehen. HINWEIS! Den Anlasser nicht jeweils l ä nger als ca.
42 5 Esp I NL F Eng D Eng D F IMPORTANT! COLD STARTING FOR HYDRO IMPORTANT: COLD STARTING FOR HYDRO (BELOW 40 ° F[4 ° C]) - AFTER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEU- TRAL (N) POSITION AND RELEASING CLUTCH/BRAKE PEDAL.
43 5 IMPORTANT: SI VOTRE TRANSMISSION DEMANDE L ’ ENL È VEMENT POUR L ’ ENTRETIEN OU LE REMPLACEMENT, ELLE DEVRAIT Ê TRE PURG É E APR È S LA R É INSTALLATION ET AVANT D ’ UTILISER LE TRACTEUR. • Garez le tracteur avec s û ret é sur un terrain plat pour qu ’ il ne roule pas dans aucune direction.
44 5 D Eng F Esp I NL NOTA! La m á quina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posici ó n de acoplamiento.
45 5 Eng D F NL Esp I Consejos para el corte • Limpie el c é sped de piedras y otros objetos que puedan ser proyectados por las cuchillas. • Localice y marque piedras y otros objetos a fin de evitar el choque con ellos. • Empiece con una altura de corte alta y vaya disminuy é ndola hasta alcanzar el resultado deseado.
46 5 Esp NL I Eng D F ATTENTION, DANGER! • Ne pas conduire sur un terrain inclin é de plus de 10 º . Le risque de se renverser est tr è s important. • Ne jamais conduire le tracteur parall è lement à la pente à cause du risque de se renverser.
47 5 Esp NL I Eng D F Use the left side of the machine to cut close to trees, bushes and paths, etc. The blade cuts about 15 mm inside the edge of the cover. Die linke Seite der Maschine benutzen, um in der N ä he von B ä umen, Geb ü sch, G ä ngen usw.
48 5 I NL Arresto del motore Portare il comando del gas su “ ” (lento). Portare la leva di azionamento del dispositivo di taglio su “ disinserito ” , verso il basso.
49 D ADVERTENCIA! Antes de proceder a efectuar el servicio en el motor o en el equipo de corte, hay que hacer lo siguiente: • Apretar el pedal del embrague/freno y acoplar el freno de estacionamiento. • Poner la palanca de cambios en punto neutro.
50 6 Cubierta del motor • Levante la cubierta. • Desenchufe el conector de cables de los faros delanteros. • Col ó quese delante del tractor. Mueva la cubierta hacia ambos lados, incl í nela hacia delante y extr á igala. • Para volver a ponerla, debe introducir los ejes de giro en las ranuras correspondientes del chasis.
51 6 Mantenimiento NOTA : El mantenimiento peri ó dico ha de hacerse con regularidad a fin de mantener el tractor en buen estado. ADVERTENCIA : Antes de efectuar cualquier reparaci ó n, inspecci ó n o maintenimiento, desconectar el cable de la buj í a a fin de evitar accidentes.
52 6 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap.
53 6 Change engine oil ............................................................................ • Lubricate pivot points ........................................................................ • Check brake operation .........................
54 6 COMPE-RENDU D'ENTRETIEN Indiquer les dates apr è s chaque mesure d'entretien Vidange d'huile moteur ..................................................................... • Graissage des articulations ............................
55 6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessit à Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore Cambio dell'olio ............................................................................
56 6 Eng Blades For best results mower blades must be kept sharp. Replace bent or damaged blades. Sharpening can be carried out with a file or grinding disc. NOTE! It is very important that both blades are sharpened equally to avoid imbalance. Blade Removal: • Raise mower to highest position to allow access to blades.
57 6 Lame Per avere il migliore risultato di taglio, è necessario che le lame siano ben affilate. Sostituirle se usurate o danneggiate. A tale scopo utilizzare una lima o una mola. OSSERVARE! E ’ importante affilare le due estremit à della lama in modo uniforme per non creare disequilibri.
58 6 1-9/16" 40 mm 1 2 Eng D F Esp I NL Eng D F Esp I NL Esp I NL Eng D F 1. Measure the distance between the brake lever and the adjuster nut. 2. The distance should be 40 mm (1.56"). 3. Adjust the distance if necessary by first loosening the lock nut (2) and then adjusting with the nut (1).
59 6 Dismantling of the cutting unit Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the small retainer spring (2) and lift clutch spring off the pulley bolt. 3. Remove the large retainer spring (3), slide collar off and push housing guide out of the bracket.
60 6 5 6 7 Assembly of the cutting unit • Push in the cutting unit under the machine. The ejector opening should be to the right. • Assemble in the reverse order to dismantling. Einbau des M ä hdecks • M ä hdecks unter den Traktor schieben. Die Auswurfoffnung mu ß nach rechts.
61 6 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previousley. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order.
62 6 B A Eng D F Esp I NL Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position.
63 6 D Eng F Esp I NL SIDE-TO-SIDE ADJUSTMENT • Raise mower to highest position. • At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “ A ” should be the same or within 6mm (1/4") of each other.
64 6 Replacement of drive belt Dismantle the cutting unit as described previously Engage the parking brake and work off the belt upwards from the pulley (1), the clutch pulley (2) and the engine's drive wheel (3). Push the belt up between two fan blades and rotate the fan clockwise until the belt comes loose (4).
65 6 TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment should not be necessary. • Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion control lever until tractor does not move forward or backward.
66 6 Esp I NL 1 2 3 Esp NL I REGULACI Ó N DE LA PALANCA DE CONTROL DEL MOVIMIENTO DEL CAMBIO MEC Á NICO La palanca de control del movimiento del cambio mec á nico ya viene predefinida por la Casa constructora y por lo tanto no requiere ulteriores regulaciones.
67 6 TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean.
68 7. Fault T racing. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole.
69 7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne d é marre pas 1. Manque d ’ essence dans le r é servoir. 2. Bougie d ’ allumage d é fectueuse. 3. Raccord de bougie d é fectueux. 4. Impuret é s dans le carburateur ou la canalisation de carburant Le d é marreur n ’ entra î ne pas le moteur 1.
70 7. Ricerca guasti. 7. Het localiseren van fouten. NL Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. Il motorino di avviamento non fa girare il motore 1.
71 8. Storage. 8. Aufbewahrung. 8. Rangement. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. • Touch up all chipped paint surfaces in order to avoid corrosion.
8. Rismessaggio. 8. Stallen. NL I Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coper- chio della falciatrice. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l ’ olio del motore.
An important point after buying a device Husqvarna YTH130 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna YTH130 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna YTH130 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna YTH130 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna YTH130 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna YTH130, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna YTH130.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna YTH130. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna YTH130 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
