Instruction/ maintenance manual of the product TS 250 XL Husqvarna
Go to page of 22
1.
2 NOTE: Part Numbers that have an ASTERISK (*) sufx may not be active 9-digit numbers. The ‘542’ prex have been added to current 6-digit part numbers and ‘0’ to 8-digit part numbers. EVER Y MACHINE IS THOROUGHL Y TESTED BEFORE LEA VING THE F ACTOR Y .
3 Symbol Denitions Symboles Denición De Los Simbolos • Please read the instructions for use prior to operating the machine for the rst time.
4 • Motor Off • Arrêt Du Moteur • Parar El Motor • Use In Well V entilated Area • A Utiliser Dans Un Endroit Bien V entilé • Usar En Una Área Bien V entilada • Do Not Use In Flammable.
5 W ARNING HEARING HAZARD DURING NORMAL USE OF THIS MACHINE, OPERA TOR MA Y BE EXPOSED TO A NOISE LEVEL EQUAL OR SUPERIOR T O 85 dB (A) A TTENZIONE!!! RISCHIO DE LESIONE ALL ’APP ARA TO UDITIVO NELL.
6 542 18 70-43* Location: T op of Belt Guard 542 04 63-26* Location: Motor Assembly 542 18 92-47* Location: Elec. Motor DECALS & LOCA TIONS ETIQUET AS Y SU UBICACIÓN AUT OCOLLANTS ET LEURS EMPLACEMENTS DUST W ARNING Cutting, especially when DR Y cutting, generates dust that comes from the material being cut, which frequently contains silica .
7 P/N 542 04 63-27* Location: Motor Assembly DECALS & LOCA TIONS ETIQUET AS Y SU UBICACIÓN AUT OCOLLANTS ET LEURS EMPLACEMENTS 542 19 07-40 (x2) Location: Both Sides of Pan 542 19 07-39 Location:.
8 DO read this entire operator ’s manual before operating this machine. Understand all warnings, instructions, and controls . DO keep all guards in place and in good condition. DO wear safety approved hearing, eye, head and respiratory protection. DO read and understand all warnings and instructions on the machine.
9 DO NOT operate this machine unless you have read and understood this operator ’s manual. DO NOT operate this machine without the blade guard, or other protective guards in place. DO NOT stand behind or in front of the blade path while the motor is running.
10 FIGURE 1 Assembly Component Identication A. Pan Guides B. Pan Stops C. Drain Plug D. Bearing Cap & Fasteners E. TIle Saw Wrench (15/16” x 9/16” x 1/2”) F . Locking Knob G. Lockbar H. W ater Pump J. Hose Barb Fitting K. W ater V alve L.
11 These signs will give advice for your safety Bef ore leav ing our fac tor y eve ry ma chi ne is th oro ugh ly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions. INSTRUCTION INDICA TION INFORMA TION W ARNING PROHIBITION Use : Sawing of any kind of tile, up to 31” (787mm).
12 IF ANY P ARTS ARE MISSING OR DAMAGED, PLEASE CONT ACT YOUR Husqvarna CUST OMER SERVICE FOR INSTRUCTIONS. CALL 1-800-288-5040 T ools required: Y our new saw can be completely as - sembled with the Wrench (E) provided.
13 1. Rai se the Bla de Guar d (M) to full y up and tigh ten the wing nut on the side to hold it in the raised position. 3. Remove the Arbor Nut (O) and the Outer Blade Flange (P). 4. Check the Blade (Q) for Counter Clockwise rotation (CCW) and install on the spindle shaft against the Inner Blade Flange (R).
14 Good motor performance depends on proper vo lta ge . Ext ens io n co rds tha t ar e too lon g an d/ or too small in wire gauge reduce the voltage to the motor under load. Use extension cords no smaller than indicated below . The motor is equipped with a manual overload protection reset button.
15 9 PROFILE WHEEL SET -UP AND USE See Figure 1 The TS 250 XL is designed for use with a Husqvarna® 6” Prole Wheel, such as P/N 542 62 10-81* (3/8” Radius) or 542 62 10-82* (1/2” Radius). • Raise the blade guard. Remove the spindle nut and outer ange.
16 If W ater Stops Flowing , 1. Stop Sawing , then 2. Disconnect Electrical Plug from Outlet , then 3. Remove the Pump , then 4. Back Flush. Back ushing is done by forcing water into the pump discharge and out through the screen. Most of the time this procedure works, and the pump can be put back into service.
17 The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy , we reserve the right to make any and all technical modications without prior notice.
18 Diagram 1: Wiring Diagram 542 20 30-79, 1.5HP , 1 15V/60/1 NOTE: Motors used on this unit are manufactured by Baldor Electric Compan y . For any motor servicing or warranty work, the motor must be taken to a Baldor Authorized Service Center . The Service Center nearest you can be found on the Internet under www .
19 Diagram 2: Wiring Diagram 542 00 06-05, 1.5 HP , 1 15V/208-230/60/1.
20 NOTES: NOT AS: REMARQUE :.
21 Serial Number: Model Number: Date of Purchase: Where Purchased: Please record the Date of Purchase and the Serial Number , the Model Number of the equipment and the Date of Purchase of your equipment in the space below . When ordering service items, please have this information available.
22.
An important point after buying a device Husqvarna TS 250 XL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna TS 250 XL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna TS 250 XL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna TS 250 XL you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna TS 250 XL will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna TS 250 XL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna TS 250 XL.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna TS 250 XL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna TS 250 XL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
