Instruction/ maintenance manual of the product RTT900 Husqvarna
Go to page of 29
R TT900 Owner's Manual / 96093000903 / 2009-04.
2 • Never operate the tiller without proper guards, plates, or other safety protective devices in place. • Keep children and pets away . • Do not overload the machine capacity by attempting to till too deep at too fast a rate. • Never operate the machine at high speeds on slippery surfaces.
3 CONGRA TUL A TIONS on your purchase of a new tiller . It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per form ance. Should you experience any prob lems you can not easily remedy , please contact your nearest authorized service center .
4 TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA TOR’S POSITION (See Fig.
5 AS SEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. Fig. 4 UNP ACKING CARTON (See Fig. 2) CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material.
6 AS SEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA TOR REMOVE TILLER FROM CRA TE • Make sure shift lever indicator is in “N” position (See Fig. 7) • Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton.
7 KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
8 OPERA TION 00155 TINE OPERA TION - WITH WHEEL DRIVE • Always release drive control bar before moving shift lever into another position. • Tine movement is achieved by moving shift lever to ( ) till position and engaging drive control bar .
9 TO TRANSPORT CAUTION: Before lifting or trans port ing, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE Y ARD • Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller .
10 OPERA TION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).
11 OPERA TION 321 5 4 67 Fig. 14 CUL TIVA TING Cultivating is destroying the weeds between rows to pre- vent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil.
12 MAINTENANCE GENERAL RECOMMENDA TIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. T o receive full value from the warranty , the operator must main tain tiller as instructed in this manual.
13 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG Fig. 16 Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel.
14 MAINTENANCE Fig. 19 MUFFLER Do not operate tiller without muffler . Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect pe ri odi cally and re place if nec es sary . If your engine is equipped with a spark arrester screen assembly , re move every 50 hours for cleaning and inspection.
15 SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.
16 SERVICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION Fig. 23 TO REPL ACE GROUND DRIVE BEL T (See Figs. 22 and 23) • Remove belt guard as described in “TO REMOVE BEL T GUARD”.
17 SERVICE AND ADJUSTMENTS t i n e_ 12 Fig. 25 • T o maintain the superb tilling performance of this ma- chine the tines should be checked for sharpness, wear , and bending, particularly the tines which are next to the transmission. If the gap between the tines ex ceeds 3-1/2 inches they should be replaced or straight ened as necessary .
18 STORAGE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remove spark plug. • Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder . • Pull starter handle slowly several times to distribute oil.
19 TROUBLESHOOTING POINTS Will not start 1 Out of fuel. 1 Fill fuel tank. 2 Fuel valve “OFF” 2 T urn fuel valve to the “ON” position. 3 Engine Switch “OFF ” 3 T urn engine switch to the “ON” position. 4 Engine not “CHOKED” properly .
20 REP AIR P ARTS TILLER - - MODEL NUMBER RTT900 (96093000903), PRODUCT NUMBER 960 93 00-09 HANDLE ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 23 532 08 67-77 Screw , Hex Washer SL T#10-24 x .
21 KEY P ART NO . NO . DESCRIPTION 3 873 22 06-00 Nut, Hex 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard RT 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Lever , Shift 7 872 11 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
22 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS TILLER - - MODEL NUMBER RTT900 (96093000903), PRODUCT NUMBER 960 93 00-09 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Locknut.
49 State Service Kit Exploded 208cc 042809 31 32 37 10 5 25 27 1 17 11 12 6 20 3 7 2 19 24 26 16 15 23 14 36 34 18 8 29 9 30 28 4 13 21 1 532420578 CYLINDER HEAD SERVICE KIT 2 532420579 PUSH ROD SERVI.
23 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 1 532 18 85-54 T ransmission Assembly (In cludes Key Nos. 2-53) 2 532 18 84-82 Gearcase, L.H. w/Bearing (In cludes Key No. 4) 3 532 16 19-63 Gasket, Gearcase 4 532 00 50-20 Bearing, Needle 5 532 00 13-70 Washer , Thrust 5/8 x 1.
24 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr . 5 25 532 12 47-17 Cap, Vinyl 26 532 10 92-27 P ad, Idler 27 532 12 54-51 Shield, Leveling 28 532 12 05-88 Pin, Hinge 29 532 40.
25 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 00 44-59 Tine, Outer , L.H. 2 532 13 26-73 Clevis Pin 3 532 00 65-54 Tine, Inner , L.H. 4 532 12 46-60 Retainer , Spring Zinc 5 532 13 27-21 Assembly , Hub and Plate, L.H. 8 874 61 06-16 Bolt, Hex 3/8-24 x 1 9 532 00 44-60 Tine, Outer , R.
26 1 532 42 20-12 Decal, Belt Guard 2 532 42 83-27 Decal, Console 3 532 42 83-33 Decal, Console Instruction 4 532 42 83-28 Decal, Tine Shield 5 532 11 06-14 Decal, Hand Placement 6 532 10 21-80 Decal, Shift Indicator 7 532 42 29-72 Decal, Warning 9 532 12 00-76 Decal, Warning, Rotating Tines 10 532 42 03-32 Decal, Engine, AC KEY P ART NO .
27 SERVICE NOTES.
532 42 84-30 04.09.09 CL Printed in U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from def.
An important point after buying a device Husqvarna RTT900 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna RTT900 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna RTT900 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna RTT900 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna RTT900 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna RTT900, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna RTT900.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna RTT900. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna RTT900 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
