Instruction/ maintenance manual of the product K3000 Husqvarna
Go to page of 20
E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3000, K3000 W et Oper ator’ s manual Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ..........................................
4 – English WHA T IS WHA T? What is what on the power cutter - K3000? 1 2 3 4 5 6 7 8 10 11 12 14 15 9 6 13 1 Rear handle 2 Guard f or the blade 14” 3 Cutting blade 4 Locking the axle 5 F ront han.
English – 5 WHA T IS WHA T? What is what on the power cutter - K3000 W et? 1 Rear handle 2 Guard f or the blade 3 W ater kit 4 Cutting blade 5 Locking the axle 6 F ront handle 7 Inspection cov ers 8.
6 – English SAFETY INSTR UCTIONS Steps before using a ne w power cutter • Please read the operator’ s manual carefully and make sure you understand the instructions bef ore using the machine. • The machine is only designed f or cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes.
English – 7 SAFETY INSTR UCTIONS General safety warnings Sav e all war nings and instructions for future ref erence. The term ”power tool” in the war nings refers to y our mains- operated (corded) pow er tool or battery-operated (cordless) power tool.
8 – English SAFETY INSTR UCTIONS P ersonal safety • Sta y aler t, watch what you are doing and use common sense when operaing a pow er tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pow er tools ma y result in serious personal injur y .
English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s saf ety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine .
10 – English SAFETY INSTR UCTIONS Ground fault cir cuit interrupter (K3000 W et) Ground f ault circuit interrupters are for protection in case an electrical fault should occur . The LED indicates that the ground f ault circuit interr upter is on and that the machine can be s witched on.
English – 11 SAFETY INSTR UCTIONS Blade vibration The blade can become out-of-round and vibr ate if an e xcessive f eed pressure is used. A lower f eed pressure can stop the vibration. Otherwise replace the blade . The blade must be of the recommended type f or the material to be cut.
12 – English SAFETY INSTR UCTIONS Dry cutting with diamond blade W et cutting with diamond blade (K3000 Wet) W ater cooling, which is used when cutting concrete, cools the blade and increases its service life while also reducing the f ormation of dust.
English – 13 SAFETY INSTR UCTIONS • The guard f or the cutting equipment should be adjusted so that the rear section is flush with the work piece. Spatter and sparks from the mater ial being cut are then collected up by the guard and led a way from the user .
14 – English ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed for hand-held pow er cutters. Blades are manufactured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1").
English – 15 ST AR TING AND ST OPPING Star ting and stopping Before starting (K3000 Wet) W ater connector Connect the water hose to the w ater supply (A). The water flow is regulated using the w ater tap (B). Ground fault cir cuit interrupter Make sure the g round f ault circuit interrupter is switched on.
16 – English MAINTENANCE Maintenance Cooling system The machine is equipped with an efficient f an to cool the motor . Cooling air which is drawn in through the grille by the machines rear handle passes ov er the stator and rotor and out through the front of the motor housing.
English – 17 MAINTENANCE Changing the grease The f ollowing parts must be dismantled to change the grease in the gear housing: 1 Flange washers holding the cutting b lade 2 The sealing ring 3 Suppor t flange for the guard 4 Guard f or the blade 5 The f our screws holding the shield.
18 – English TECHNICAL D A T A ´®z+S3•¶52¨ ´®z+S3•¶52¨ Cutting equipment Max. blade speed, rpm 4500 T echnical data K3000 K3000 W et Engine Protection class I I Ground f ault circuit int.
.
´®z+S3•¶52¨ 2008-06-11 ´®z+S3•¶52¨ 1151199-95 ! W ARNING! Cutting, especially when DR Y cutting, generates dust that comes from the material being cut, which frequentl y contains silica. Silica is a basic component of sand, quar tz, bric k cla y , granite and numer ous other minerals and r ocks.
An important point after buying a device Husqvarna K3000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna K3000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna K3000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna K3000 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna K3000 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna K3000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna K3000.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna K3000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna K3000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
