Instruction/ maintenance manual of the product 966957301 Husqvarna
Go to page of 20
505 29 00-57 04.21.08 CL PRINTED IN U.S.A. OWNER/OPERA TOR MANU AL Model: CT20 / 966957301 SPECIFICA TIONS • Durable T ecumseh TC III Engine • P ositive On/Off Switch • Heavy-Duty Handlebars wit.
2 SAFETY RULES AND PRECAUTIONS As with any item of power equipment it is necessary that you learn and observe ALL safety precautions. This includes the care for the machine as well as personal safety . This machine is only as dangerous as the person who is operating it.
3 9. Before cleaning, repairing, or inspecting, STOP THE ENGINE, make certain all moving parts have stopped, and disconnect the spark plug wire. 10. NEVER run engine indoors. Exhaust fumes contain Carbon Monoxide which is an ODORLESS and DEADL Y POISONOUS GAS.
4 T ABLE OF CONTENTS DESCRIPTION P AGE Safety Rules and Precautions.......................................................................................................2-3 Assembly ....................................................................
5 AS SEMBL Y With the exception of handlebars, controls and transport kit, your new tiller has been completely assembled at the factory . It should be noted that right and left sides are determined by the operators position behind the unit. HANDLEBARS (L OWER) (See Fig.
6 THROTTLE CABLE Unwind throttle cable from around engine. CAUTION: Be careful not to kink cable. ON/OFF SWITCH 1. Place 1 3/8” long slotted pan head screw into switch plate and down through hole in upper right hand handlebar . (See Fig. 2) 2. Place rubber isolator over screw underneath handlebar .
7 WARNING-24:1- Disregard instructions on oil containers. Do not mix directly in fuel tank. Do not use multi-viscosity oils. Use high speed air cooled 2-cycle oil . U.S Imperial Metric Gas Oil Gal. Oz. Gas Oil Gal. Oz. Gas Oil Gal. Oz. 1 5 2 10 1 6 2 12 4 166 8 322 T o start engine, place the unit in a flat, clear area.
8 WARNING: When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury . T o avoid this risk, carefully follow these instructions: Move rocker switch to "I" position. 5. Grasp starter cord handle. Se Fig.
9 TINE SP ACERS The two tine spacers provided can be used to replace outside tines to narrow tilled path. DANGER! AL WA YS MOVE SWITCH TO "O" POSITION AND REMOVE SP ARK PLUG WIRE BEFORE TRYING TO REMOVE OBSTRUCTIONS. CLEAN UNIT AFTER EACH OPERA TION.
10 TO CLEAN SCREEN a) Wash SCREEN in water and detergent solution. b) Rinse thoroughly in clean water , then air dry . TO CLEAN AND RE-OIL FOAM FIL TER a) Wash FOAM FIL TER in water and detergent solution and squeeze (don’t twist) until all dirt is removed.
11 4).% (5" ./4%ª(5" 0/3)4)/.ª). 2%, ! 4)/.3()0 4/ª4).%3 &2/.4 /&ª4),,%2 34/.9ª3/),ª0 ! 44%2.ªA 34/.9ª3/),ª0 ! 44%2.ªB &2/.4 /&ª4),,%2 &2/.4 /&ª4),,%2 2%'5, !2ª4).%ª0 ! 44%2. ª ª ª 4.
12 IDLE SCREW NARROW CUL TIVA TING The two outer tines can be removed to give you a narrower cultivating width. This width is approximately 6". This will give you the ability to get between very closely spaced plants. In order to do this, pull the hairpin out of the hole in the outboard end of the tine shaft.
13 HANDLEBARS/GRIP/ON-OFF SWITCH/ THROTTLE CONTROL/THROTTLE CABLE ITEM ORDER NO . NO. DESCRIPTION QTY . REQ. 1 505 29 00-01 Grip, Handlebar 2 2 505 29 00-02 Screw , #10-24 x 1 3/8 1 3 505 29 00-03 Swi.
14 TRANSMIS SION ASSEMBL Y ITEM ORDER NO . NO. DESCRIPTION QTY . REQ . 1 505 29 00-18 Seal 2 2 505 29 00-19 Screw , Phillips Pan Hd 1/4-20 x 1/2 2 4 505 29 00-20 Bushing, Bronze 2 5 505 29 00-21 Drum .
15 ENGINE/TRANSMIS SION/TINES/SHIELD ITEM ORDER NO . NO . DESCRIPTION QTY . REQ. 1 – – – – – – – Engine* 1 2 505 29 00-61 Clutch Assy 1 3 505 29 00-62 Spring, Clutch 2 4 505 29 00-39 Dra.
16 TRANSPORT KIT AS SEMBL Y 1. Assemble the wheel assembly and install the wheel assembly on the tiller with the arrow up as shown. T orque: 14 ft-lb (20 N-m).
17 NOTES.
18 NOTES.
19 NOTES.
SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the d.
An important point after buying a device Husqvarna 966957301 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 966957301 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 966957301 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 966957301 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 966957301 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 966957301, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 966957301.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 966957301. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 966957301 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
