Instruction/ maintenance manual of the product 96045000901 Husqvarna
Go to page of 48
YTH2348 Owner's Manual / 96045000901 / 2008-09.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 OPERA TION FIG. 4 TO USE CHOKE CONTROL (N) (See Fig. 6) Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
11 S FIG. 10 OPERA TION REVERSE OPERA TION SYSTEM (ROS) (See Fig. 11) Y our tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. T o avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer .
13 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time.
14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
15 MAINTENANCE FIG. 15 BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight.
16 MAINTENANCE TO CHANGE ENGINE OIL (See Figs. 16 and 17) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container .
17 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. AIR FIL TER Y our engine will not run properly using a dirty air filter .
18 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key .
19 SERVICE AND ADJUSTMENTS D C • A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring. • Repeat on opposite side of tractor . FIG. 25 NOTE: Be su re mower side suspension arms (A) are pointing forward before sliding mower under tractor .
20 H F J G E FIG. 26 M • Engage belt tension rod (K) on locking bracket (L). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly . • Raise attachment lift lever to highest position. • If necessary , adjust gauge wheels before op er at ing mower as shown in the Operation section of this manual.
21 TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig.
22 TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 33) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L).
23 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 34) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual).
24 SERVICE AND ADJUSTMENTS FIG. 36 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY REPL ACING BA TTERY (See Fig. 37) WARNING: Do not short battery ter mi nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc.
25 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. W ait several minutes before attempting to start. 4. Bad spark plug.
28 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
30 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 101 40 71 34 With Service Minder Option 46 46 With 12V O.
31 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 41 41-25 Batt.
32 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 CHASSIS 182 68 68 176 176 175 178 165 228 228 183 194 236 150 180 68 68 213 52 218 34 130 130 177 chassis-te x_69-gt-husq_r2 233.
33 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 CHASSIS 3 532 40 50-12 Logo 5 532 40 87-01 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille Asm.
34 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 DRIVE 52 51 170 171 225 125 drive-te x_K46_pedal_28 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 56 213 221 160 206 26 207 .
35 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 DRIVE KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532405384 T ransaxle, TUF F TORQ K46 BT (Internal parts not available) 2 532 12 35-83 Key 15 819 13 13-16 W asher 13/32 x 13/16 x 16 Ga.
36 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 ENGINE 28 113 110 109 111 1 29 SP ARK ARRESTER KIT 84 45 22 21 20 62 71 70 79 69 87 2 engine-te x_bs-2cyl_14 81 82 37 28 37 12 1.
37 KEY P ART NO . NO. DESCRIPTION 1 - - - - - - Engine Briggs Model No. 445577-0755-G1 2 532 14 97-23 Muffler 9 532 19 43-20 Keeper Belt Engine 11 532 40 00-08 Clutch Electric 12 532 40 50-97 Pulley Engine 15 532 41 41-51 T ank F uel 18 532 42 06-35 Cap Asm 20 532 17 83-85 Control Throttle 21 532 41 63-58 Screw #10 x 0.
38 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_4-husq KEY P ART NO . NO.
39 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 SEA T ASSEMBL Y 2 6 1 40 10 37 37 21 21 3 41 7 8 7 8 seat-tex_6.5SL_3 44 43 8 8 6 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
40 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 MOWER DECK 47 7 46 32 33 31 30 1 33 208 48 52 43 54 97 33 49 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 194 113 17 21 49 187.
41 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 35-82 Deck Weldment Mower 6 532 19 72-48 Cover Mandrel LH 7 532 19 91-02 Cover Mandrel RH 8 532 17 43-65 Bolt 7/16 Asm.
42 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-tex_3 89 87 89 87 2 532 19 52-23 Shaft Asm.
43 TRACTOR - MODEL NO . YTH2348 (96045000901), PRODUCT NO. 960 45 00-09 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO .
44 SERVICE NOTES.
45 SERVICE NOTES.
46 SERVICE NOTES.
47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
532 42 06-30 Rev . 2 09.12.08 SBW Printed in U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free.
An important point after buying a device Husqvarna 96045000901 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 96045000901 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 96045000901 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 96045000901 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 96045000901 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 96045000901, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 96045000901.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 96045000901. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 96045000901 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
