Instruction/ maintenance manual of the product 96043005200 Husqvarna
Go to page of 44
200 7-12 O0 7 020 37 YTH 2 1 4 6 XP ( C A) Operator's Manual Operator' s Manual Ride M o wer 960 43005 2 00 03002.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). Y our new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. A TO MOVE FORWARD AND BACK WARD (See Fig. 7) The direction and speed of movement is controlled by the forward and reverse drive pedals.
11 TO OPERA TE MOWER (See Fig. 10) Y our tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.
12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. T o avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer .
13 FIG. 12 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
15 MAINTENANCE FIG. 13 TRACTOR Always observe safety rules when per form ing any main- te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
17 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. AIR FIL TER Y our engine will not run properly using a dirty air filter .
18 E F M K G B G A Q R P C D L SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position.
19 E F M K G B G A Q R P C D L SERVICE AND ADJUSTMENTS • A TT ACH REAR LIF T LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D) on rear mower bracket and secure with washer and retainer spring. • Install belt on engine pulley (M), in belt keepers (G).
20 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT - TO -BACK ADJUSTMENT (See Figs. 23 and 24) IMPORT ANT : Deck must be level side-to-side.
21 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 26) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual).
22 SERVICE AND ADJUSTMENTS FIG. 27 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 28) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies.
23 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. W ait several minutes before attempting to start. 4. Bad spark plug.
26 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
27 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 SCHEMA TIC NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVE.
28 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 101 40 71 34 With Service Minder Option 46 46 Wit.
29 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 14 49-27 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 18 64-91.
30 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 CHASSIS 14 214 130 130 37 194 194 52 52 181 181 182 68 68 189 176 176 176 175 178 165 219 219 183 52 236 152 150 202 203 .
31 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 CHASSIS KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.
32 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 DRIVE 52 51 170 171 225 125 drive-te x_K46_pedal_17 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 56 213 221 160 206 .
33 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 DRIVE KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532405384 T ransaxle, TUF F TORQ K46 (Internal parts not available) 2 532 12 35-83 Key 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
34 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 ENGINE 1 92 12 11 41 42 85 9 29 SP ARK ARRESTER KIT 92 45 90 31 37 28 37 21 20 22 62 70 71 86 69 87 2 engine-tex_23-ka wa.
35 KEY P ART NO . NO. DESCRIPTION TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 ENGINE NOTE: All component dimensions given in U.
36 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 STEERING ASSEMBL Y 61 steering-tex_LEGND2_16 21 1 26 35 19 60 59 58 57 63 57 63 63 5 62 15 14 13 13 53 8 70 68 69 16 28 2.
37 KEY P ART NO . NO. DESCRIPTION 1 532 19 39-43 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm.
38 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 SEA T ASSEMBL Y 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/Ins.
39 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
40 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 MOWER DECK 55 30 32 31 33 56 34 57 59 62 197 188 1 69 69 69 199 40 3 46 145 46_te x_lt_pred_18 15 14 13 11 8 21 25 26 27 .
41 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 MOWER DECK KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.
42 TRACTOR - - MODEL NUMBER YTH2146XP (96043005200), PRODUCT NO . 960 43 00-52 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-te x_7 91 91 89 87 100 2 532 19 52-23 Shaft Asm.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
532 41 88-57 12-12-07 SBW Printed in the U.S.A..
An important point after buying a device Husqvarna 96043005200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 96043005200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 96043005200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 96043005200 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 96043005200 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 96043005200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 96043005200.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 96043005200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 96043005200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
