Instruction/ maintenance manual of the product 917.37581 Husqvarna
Go to page of 28
Model No . 917.375810 CA UTION: Read and f ollow all Saf ety Rules and In struc tions bef ore operating this equipment Owner’ s Manual R O T AR Y LA WN MO WER 6.75 Horsepo wer P o wer-Propelled 22" Multi-Cut Husqv ar na, Charlotte, NC 28269 U .
2 W arranty ................................................... 2 Saf e ty Rules .......................................... 2-4 Prod uct Spec i fi ca tions .............................. 5 Assembly / Pre-Oper ation ........................ 6 Op er a tion .
3 DO: • Mow across the f ace of slopes: ne v er up and down. Ex ercise extreme caution when changing direction on slopes. • Remov e obstacles such as rocks , tree limbs, etc. • W atch f or holes, ruts, or b umps. T all grass can hide obstacles .
4 W ARRANTY SECTION 1: LIMITED W ARRANTY Husqvarna F orest & Garden Company (“Husqvarna”) warrants Husqv arna product to the or iginal purchaser to be free from def ects in mater ial and workm.
5 Serial Number : Date of Purchase: Gasoline Capacity / T ype: 1.6 Quar ts (Unleaded Regular) Oil T ype (API SG–SL): SAE 30 (above 32°F); SAE 5W -30 (below 32°F) Oil Capacity: 20 Ounces Spark Plug (Gap: .030") Champion J19LM or RJ19LM Blade Bolt T orque: 35-40 ft.
6 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety bef ore you attempt to assemb le or operate y our new la wn mower .
7 Wheel adjuster (on each wheel) IMPORT ANT : This lawn mo wer is shipped WITHOUT OIL OR GASOLINE in the engine. KNO W Y OUR LA WN MO WER READ THIS OWNER'S MANU AL AND ALL SAFETY R ULES BEFORE OP ER AT ING Y OUR LA WN MO WER.
8 1. T ur n unit off and disconnect spark plug wire from spark plug. 2. T ur n nut on underside of driv e control to increase drive speed. 3. Operate mo wer to test drive speed. Readjust as required. 4. If condition f ails to improv e after the abov e steps (f orward speed remains the same), your driv e belt is wor n and should be re placed.
9 Open mulcher door Discharge defl ector Mulcher plug SIDE DIS CHARG ING • Mulcher plug must be installed into rear discharge open ing of mower . • Open mulcher door and install dis- charge defl ector under door as sho wn. • Mow er is now ready f or discharging operation.
10 NO TE: Initial oil fi ll requires only 18 oz. due to residual oil in engine from the manuf acturers 100% quality testing. When changing oil you ma y need 20 oz. 4. Inser t and tighten dipstick. IMPORT ANT : • Check oil le vel bef ore each use. Add oil if needed.
11 MULCHING MO WING TIPS IMPORT ANT : F or best performance, keep mo wer housing free of b uilt-up grass and tr ash. See “CLEANING” in the Maintenance section of this manual.
12 GENERAL REC OM MEN DA TIONS The warr anty on this lawn mow er does not cov er items that hav e been sub ject ed to operator ab use or negligence. T o receiv e full v alue from the warranty , operator m ust maintain unit as in str uct ed in this manual.
13 4. Use bloc k of wood between blade and lawn mo wer housing and tighten the blade bolt, turning clockwise . • The recommended tightening torque is 35-40 ft. lbs. IMPORT ANT : Blade bolt is heat treated. If bolt needs replacing, replace only with approv ed bolt shown in the Repair P ar ts section of this manual.
14 7. Continue adding small amounts of oil, rechecking the dipstic k until oil le vel settles at FULL. DO NO T ov erfi ll, or engine will smoke hea vily from the muf- fl er on star tup . 8. Alwa ys be sure to retighten oil dipstick bef ore star ting engine.
15 T O ADJUST HANDLE The handle can be mounted in a high or low position. The mounting holes in the bottom of low er handle are off center for raising or lo wering the handle. 1. Remov e upper handle and wire tie(s) securing cable(s) to low er handle.
16 your la wn mow er to a Husqvarna or other qualifi ed service center for repair and/or ad just ment. IMPORT ANT : Nev er tamper with the engine gov er nor , which is f actor y set f or proper engine speed. Ov er speed ing the engine abov e the f actor y high speed setting can be dangerous.
17 gum deposits during stor age . Add stabilizer to gasoline in fuel tank or storage container . Alwa ys follo w the mix ratio f ound on stabilizer container . Run engine at least 10 min utes after adding stabilizer to allo w the stabilizer to reach the carburetor .
18 Loss of power 1. Rear of mower housing or 1. Raise cutting height. blade dr agging in grass . 2. Cutting too much gr ass. 2. Raise cutting height. 3. Dir ty air fi lter . 3. Clean/replace air fi lter . 4. Buildup of grass , leav es, 4. Clean underside of mower and trash under mo wer .
36 HUSQV ARNA RO T AR Y LA WN MO WER - - MODEL NUMBER 917.375810 REP AIR P AR TS.
37 HUSQV ARNA RO T AR Y LA WN MO WER - - MODEL NUMBER 917.375810 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 196403 Upper Handle Assemb ly (Includes Foam Grip) 2 183567 Engine Zone.
38 HUSQV ARNA RO T AR Y LA WN MO WER - - MODEL NUMBER 917.375810.
39 HUSQV ARNA RO T AR Y LA WN MO WER - - MODEL NUMBER 917.375810 NO TE: All component dimensions given in U .S. inches. 1 inch = 25.4 mm. IMPORT ANT: Use only Original Equipment Manuf acturer (O .E.M.) replacement par ts. F ailure to do so could be hazardous, damage your la wn mower and v oid your warr anty .
40 MODEL NUMBER 125K02-0654-E1 BRIGGS & STRA TT ON 4-CYCLE ENGINE 307 13 337 635 383 3 306 11 9 10 54 50 51 7 5 585 684 287 525 524 842 1 8 847 523 27 27 32 26 28 25 29 40 40 35 36 33 45 34 45 24 .
41 MODEL NUMBER 125K02-0654-E1 BRIGGS & STRA TT ON 4-CYCLE ENGINE 104 137 276 95 127 633 617 276 130 365 125 134 975 133 11 7 163 968 445 425 443 163 529 966 976 188 104 137 276 127 633 121 CARBUR.
42 MODEL NUMBER 125K02-0654-E1 BRIGGS & STRA TT ON 4-CYCLE ENGINE 332 304 305 363 455 23 55 456 58 60 459 689 597 608 65 592 969 190 670 957 972 1059 121 1 1210 601 187 78 37 613 81 300 604 564 1329 REPLACEMENT ENGINE 1330 REP AIR MANUAL 1058 OWNER’S MANUAL 1036 EMISSIONS LABEL 921 KEY P ART NO .
43 MODEL NUMBER 125K02-0654-E1 BRIGGS & STRA TT ON 4-CYCLE ENGINE KEY P ART NO . NO . DESCRIPTION 81 691740 Lock-Muffl er Screw 95 691636 Screw (Throttle V alv e) 97 696565 Shaft-Throttle 104 691.
SER VICE NO TES.
402548 Re v . 4 05.16.06 BY Printed in U .S.A. Para pedir s ervicio de reparac ión a dom icilio, y para ordenar piezas : 1-888-SU-HO GA R ® (1-888-784-6427) Au Canada pour ser vice en français: 1-800-LE- FOYER MC (1-800-533-6937) ww w.sea rs.ca To purchase a protection ag reement (U.
An important point after buying a device Husqvarna 917.37581 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 917.37581 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 917.37581 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 917.37581 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 917.37581 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 917.37581, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 917.37581.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 917.37581. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 917.37581 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
