Instruction/ maintenance manual of the product 917.27909 Husqvarna
Go to page of 48
Husqvarna 02148 91 7.279090 Owner's Manual.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWINGSAFETY INSTRUCTIO.
SAFETY RULES & Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children.
PRODUCT SPECIFICATIONS Gasoline Capacity 5.0 Gallons and type: Unleaded Regular Oil Type (API: SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/Filter: 4.0 Pints W/O Filter: 3.75 Pints Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): Forward LO: HI: 1st 0.
UNASSEMBLED PARTS Steering Wheel Steering Sleeve i T Premium Steering Adapter _vv_teee_ r n sge r t Seat @ (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Knob Mower (2) Flanged Pins (2) Retainer Springs (double loop) J @ @ Q @ @ (4) Adjusting Bars Gauge Wheels (4) Wheels (4) Washers 3/8 x 3/4 x 14 Ga.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes, To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely.
ASSEMBLY INSTALL SEAT (See Fig. 3) Adjust seat before tightening adjustment knob, • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor, • Pivot seat upward and remove from the cardboard pack- ing.
ASSEMBLY INSTALL MOWER AND DRIVE BELT (Sees Fig. 6 and 7) See MOWER AND DRIVE BELT ASSEMBLY Supplement Sheet for additional guidance on this assembly. Be sure tractor is on level surface and mower sus.
ASSEMBLY CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes, Correct tire pressure is important for best cutting performance, ° Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
OPERATION These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their mean- ing, R L I'.,I LOW CHOKE FAST REVERSE NEUTRAL HIGH SLOW IGNITION SW.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations with your tractor to familiarize yourself with the location of vario.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while op- erating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 9) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position, Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
OPERATION TO OPERATE ON HILLS I& CAUTION: Do not drive up or down hills I with slopes greater than 15 ° and do not drive across any slope. Choose the slowest speed before starting up or down hills, Avoid stopping or changing speed on hills.
OPERATION WARM WEATHER STARTING (50° F and above) • When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke con.
MAINTENANCE AS YOU COMPLETE REGULAR SERVICE RV,OE 0 A TES /_/// Check Operator Presence and T ROS Systems R Check for Loose Fasteners if Ks A Sharpen/Replace Mower Blades I1_:_ C Lubrication Chart If .
MAINTENANCE TRACTOR Always observe safety rules when performing any main- tenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
MAINTENANCE / CENTER HOLE 5/8" BOLT OR PIN BLADE FIG. 13 BATTERY You rtractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean.
MAINTENANCE TO OPEN OIL DRAIN VALVE .... - I TO CLOSE DRAIN TUBE FIG. 16 • After oil has drained completely, close the drain valve turning clockwise. Use the 7/16" (1 lmm) wrench to apply a small amount of torque to keep it closed, Do not over tighten, • Remove the drain tube and store in a safe place.
SERVICE AND ADJUSTMENTS & WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress clutch/brake pedal fully and set parking brake. Place gearshift lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position.
SERVICE AND ADJUSTMENTS • If adjustment is necessary, make adjustment on one side of mower only. • To raise one side of mower, tighten lift link adjustment nut on that side, • To lower one side of mower, loosen lift link adjustment nut on that side, NOTE: Each full turn of adjustment nut will change mower height about 3/16".
SERVICE AND ADJUSTMENTS TO REPLACE MOWER DRIVE BELT (See Fig. 23) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface, Engage parking brake, • Lower attachment lift lever to its lowest position, • Disengage belt tension rod from lock bracket, I & CAUTION: Belt tension rod is spring I loaded.
SERVICE AND ADJUSTMENTS WITH PARKING BRAKE "ENGAGED" TO ADJUST ATTACHMENT CLUTCH (See Fig. 24) The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds, Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required.
SERVICE AND ADJUSTMENTS "_NGINE V-IDLER TRACTORV-BELT DRIVE SCHEMATIC VIEWED FROM L.H. SIDE OFTRACTOR CLUTCHING IDLER CLUTCHING FLAT IDLER ABOVE MIDSPAN BELT KEEPER BELT KEEPER BELT TWISTS BELT TRANSAXLE KEEPER PULLEY ENGINE PULLEY V-IDLER AS VIEWED FROM BOTTOM FIG.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 29) TO REPLACE FUSE Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash, & WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more, & WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING POINTS CAUSE CORRECTION PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power Excessive vibration 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine dies when tractor is shifted into reverse Engine continues to run when operator leaves seat with attachment clutch engaged Poorcut-uneven Mower b.
TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 SCHEMATIC AMMETER FUSE (OPTIONAL) PTO WHITE q_ ] J I i I BLACK I CLUTCH / BRAKE (PEDAL UP) GRAY SEAT SWITCH _NOT OCCUPIED_ BLACK ...... ,................................ .......................
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 ELECTRICAL 12 / / / ! / / / / / f [ t i i9_ I I I I 25 34 40 33 >4-5 96 16 2 i 30.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 532144927 Battery 2 874760412 Bolt Hex Head 1/4-20 x 3/4 8 532124886 Tray, Battery 10 532145211 Bolt, Battery Front 1/4-20 x 7.5 Zinc 11 532150109 Holddown Battery Front Mount 12 532145769 Nut, Push Nylon 1.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 CHASSIS AND ENCLOSURES 14 15 i_ 25 161 158 37 162 138 58 17__ 144 _130 43 34 28 17 21 2 chassis-stealth II lO-vgt 170 8s ".
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 CHASSIS AND ENCLOSURES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 532180375 Rail, Frame RH 68 817490508 2 532175.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 GROUND DRIVE 40 41 30 51 28 17 ._ 37 38 50 11 48 7 69 156 24 22 15 57 47 157 155 62 drive 9=vgt 62 34.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 3 532007563 Washer, Thrust, Axle 38 532150035 Nyliner 4 817490508 Screw Thdrol 5/16-18 x 3/4 39 874321016 Screw, Fin.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 STEERING ASSEMBLY 34 33 32 23 22 13 29 28 36 J 52 lJ > 15 1313 / /" / _, 1 / / i I tl I I I I I I it + ill _ 53 .
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 532193943 2 532178557 3 532183226 4 532161849 5 532161848 6 532124931 7 53212174.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 ENGINE 21 20 18 15 47--- _ 28 _37 26 27 39 engine-intek-ELS lO-vgt 1 8 4° I 84 84 12 I1 85 69 82 29 / I SPARK ARRESTER KIT I 38.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 ENGINE KEY PART KEY NO. NO. DESCRIPTION NO. 1 Engine Briggs, Model No, 41 40H777(Order parts from engine 42 manufacturer) 45 2 532149723 Muffler Side 47 8 532121361 Pulley V-Idler 62 9 532177748 Keeper Asm.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 SEAT ASSEMBLY KEY NO. 1 2 3 4 5 6 7 8 10 12 13 14 14 10 @i,o ! ' 4 5 18 I/6 19 )i 17 12 I I 37 I I I 21 seat l-vgt PART NO.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 15 DECALS 7 12 3 4 5 24 10 14 16 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 532178482 Decal, Deck Heavy Duty 13 532188298 2.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 LIFT ASSEMBLY 40 43 35 73 39 42 38 4 23 4 70 70 86 34 7 31 8 32 9 10 72 1 12_ /76 _ __26 ___47s -78 lift rh 16 42.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 LIFT ASSEMBLY KEY PART KEY PART NO. NO. NO. NO. DESCRIPTION 35 532138057 1 532121006 Rod Asm,, Lever 38 532155097 2 532180045 Sha.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 MOWER DECK 47 e_ 46 57 46 33 32 43 51 33 32 116 8 1 113 56 i 1 35 18 38 59 18 60 29 25 26 27 mower deck-54 2 44.
REPAIR PARTS TRACTOR - - MODEL NO. 917.279090 PRODUCT NO. 960 25 00-02 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 47 532191273 1 532194846 Deck Weldment Mower 49 873900600 5 .
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION O_ ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. _b ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
4:= "4 Husqvarna SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company ("Husqvarna") warrants Husqvama product to the original pur- chaser to be free from defects in materia.
{_ Husqvarna 532197646 02.21.05 RD Printed in U.S.A..
An important point after buying a device Husqvarna 917.27909 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 917.27909 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 917.27909 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 917.27909 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 917.27909 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 917.27909, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 917.27909.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 917.27909. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 917.27909 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
