Instruction/ maintenance manual of the product 532 43 00-01 Husqvarna
Go to page of 48
LGT2554 Owner's Manual 03002 532 43 00-01 Rev . 4.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 Y our new tractor has been assembled at the factory with ex- ception of those parts left unassembled for shipping purposes. Fig. 1 L ABEL TO CHECK BA TTERY (See Fig.
6 NOTE: Y ou may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al. Be sure tractor is in a well-ventilated area.
7 AS SEMBL Y 90° END INTEGRA TED WASHER END ANTI-SWA Y BAR (S) TOWARDS TOW ARDS TRANSAXLE MOWER DECK • F rom right side of mower , first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle.
8 AS SEMBL Y 6. A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 11) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor .
9 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP ARE.
11 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
12 Fig. 16 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
13 TO ADJUST MOWER CUT TING HEIGHT (See Fig. 20) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. TO ADJUST GAUGE WHEELS (See Fig. 21) Gauge wheels are prop er ly ad just ed when they are slight ly off the ground when mower is at the desired cutting height in operating position.
14 TO TRANSPORT (See Fig. 15 and 24) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po si tion. F ree wheel control is located at the rear drawbar of tractor . • Raise attachment lift to highest position with at tach ment lift control.
15 ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline.
16 Fig. 25 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim ming. • Drive so that clippings are discharged onto the area that has been cut.
17 LUBRICA TION CHART T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil.
18 TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
19 TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. T o prevent pos- si ble damage to seals, do not use high pressure water or steam to clean transmission.
20 00667 FUEL FIL TER CL AMP CL AMP IN-LINE FUEL FIL TER (See Fig. 29) The fuel filter should be replaced once each season. If fuel filter becomes clogged, ob struct ing fuel flow to car bu re tor , re place ment is re quired. • With engine cool, remove filter and plug fuel line sec tions.
21 Fig. 32 Fig. 33 E A M F B K C C S H D D L TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 33) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L).
22 FRONT - TO -BACK ADJUSTMENT (See Figs. 36 & 37) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 Fig. 38 TO REMOVE WHEEL (See Fig. 39) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle.
24 TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 41) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged.
25 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
26 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
28 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. F aulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
29 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
30 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
31 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V Outl.
32 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Bat.
33 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 CHASSIS 181 182 176 176 175 165 150 180 130 130 199 162 177 196 221 chassis-tex_TEX GT HUSQ_65_r1 298 238 3 5 181 176 137 137 1.
34 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 CHASSIS KEY P ART NO . NO. DESCRIPTION 3 532 40 50-12 Logo 5 532 40 87-01 Dash 14 532 41 10-46 Hood Asm.
35 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 DRIVE 56 216 143 197 196 125 226 125 125 80 125 51 231 170 175 279 176 178 174 22 23 166 232 153 233 drive-tex_K46_fender_6_r1 .
36 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 DRIVE KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 - - - - - - - - - T ransaxle, TUFFTORQ K46 AW (Internal parts not available) 2 532 18 62-11 Key 7 532 19 98-44 Hub Asm.
37 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 - - - - - - - - - Engine K ohl Model No. SV730-0034 2 532 14 97-23 Muffler 9 532 19 43-20 Keeper Belt Engine 11 532 17 93-35 Clutch Electric 12 532 19 43-43 Pulley Engine 15 532 19 34-99 T ank F uel 4.
38 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 SEA T ASSEMBL Y 1 532 42 40-68 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/Ins.
39 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 STEERING ASSEMBL Y 61 steering-tex_HUSQSR_7 21 1 26 35 19 60 59 58 63 5 62 15 14 13 13 53 8 70 68 69 16 28 28 13 22 64 4 15 14 .
40 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 STEERING ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 1 532 41 64-80 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-89 Spindle Asm., LH 5 532 40 30-90 Spindle Asm., RH 6 532 12 49-31 Bearing, Race Thrust Harden 7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.
41 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 MOWER DECK mower_dec k 54-te x_16 47 7 49 46 32 33 31 30 1 33 52 52 43 196 97 33 192 49 34 39 185 46 46 6 21 122 114 98 31 32 2.
42 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 31-25 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm.
43 TRACTOR - MODEL NO . LGT2554 (96045001502), PRODUCT NO . 960 45 00-15 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-te x_23 91 89 87 89 87 91 2 532 42 20-27 Shaft Asm.
44 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e .
45 Consumer Wheeled Produc ts – Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purc hase for the applicable Warrant y Period shown on Exhibit A .
46 c. Preventative maintenance as outlin ed in t he operator’s manual. In addition, you must cease using the product immediately upon any failure or damage. The product shoul d be taken to an authori zed Husqvarna servicing dealer prior to any further use.
47 Consumer Wheeled Warranty Chart 2010 Exhibit A Consumer (personal, household use only) Commercial (any commercial, professional, institutional, arigculutral, or income producing use, other than Ren.
06.21.10 JA Printed in the U.S.A. Consumer Wheeled Warranty Chart 2010 Exhibit A Consumer (personal, household use only) Commercial (any commercial, professional, institutional, arigculutral, or incom.
An important point after buying a device Husqvarna 532 43 00-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 532 43 00-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 532 43 00-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 532 43 00-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 532 43 00-01 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 532 43 00-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 532 43 00-01.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 532 43 00-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 532 43 00-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
