Instruction/ maintenance manual of the product 500RTT Husqvarna
Go to page of 28
500R TT Owner's Manual.
2 • K eep children and pets aw ay . • Do not ov erload the machine capacity by attempting to till too deep at too f ast a rate. • Ne v er operate the machine at high speeds on slipper y surf aces. Look behind and use care when bac king. • Ne ver allo w bystanders near the unit.
3 CONGRA TULA TIONS on your purchase of a ne w tiller . It has been designed, en gi neered and manu f ac tured to give you the best pos sib le de penda bil ity and per fo r m ance. Should you e xper ience any prob lems you can not easily remedy , please contact your nearest authorized service center .
4 T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig.
5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. HANDLE ASSEMBL Y "UP" POSITION FIG. 4 UNP A CKING CART ON (See Fig. 2) CA UTION: Be careful of e xposed sta ples when handling or disposing of cartoning material.
6 ASSEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA T OR REMO VE TILLER FROM CRA TE • Mak e sure shift lev er indicator is in “N” position (See Fig. 7) • Tilt tiller forw ard by lifting handle . Separate cardboard cov er from le veling shield.
7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to familiarize y ourself with the location of various controls and adjustments. Sav e this manual f or future ref erence.
8 OPERA TION TILLING (See Fig. 11) • Release depth stake pin. Pull the depth stake up f or increased tilling depth. Place depth stake pin in hole of depth stake to loc k in position. • Place shift le ver indicator in tilling position. • Hold the dr ive control bar against the handle to star t tilling mov ement.
9 OPERA TION TURNING • Release the drive control bar . • Mov e throttle control to “SLOW” position. • Place shift lev er indicator in “F” (forw ard) position.
10 OPERA TION • Soil conditions are impor tant for proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to e xcessive bounce and diffi cult handling of your tiller . Hard soil should be mois tened before tilling; howe v er , e xtremely wet soil will “ball-up” or clump dur ing tilling.
11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co ver items that ha ve been subjected to operator ab use or negligence. T o receiv e full value from the w arranty , the operator m ust main tain tiller as instructed in this manual.
12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming any maintenance (e xcept car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel.
13 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire fr om spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 18) Select handle height best suited f or your tilling conditions. Handle height will be diff erent when tiller digs into soil.
14 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION T O REPLA CE GROUND DRIVE BEL T (See Fig. 21) • Remov e belt guard (See “TO REMO VE BEL T GU ARD” in this section of this manual).
15 SER VICE AND ADJUSTMENTS FIG. 24 TINE REPLA CEMENT (See Figs. 22, 23, and 24) CA UTION: Tines are sharp. W ear gloves or other pr otection when han- dling tines.
16 SER VICE AND ADJUSTMENTS ENGINE CARBURET OR The carburetor has been preset at the f actor y and ad just ment should not be necessar y . Howe v er , engine per fo r mance can be aff ected by dif fe r enc es in fuel, tem per a ture, al ti tude or load.
17 Immediately prepare your tiller f or storage at the end of the season or if the unit will not be used f or 30 days or more . W ARNING: Never store the tiller with gasoline in the tank inside a build ing where fumes may reac h an open fl ame or spark.
18 Will not start 1. Out of fuel. 1. Fill fuel tank . 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se veral min utes before attempting to start. 4. Dir ty air cleaner. 4. Clean or replace air cleaner cartr idge.
19 REP AIR P AR TS TILLER - - MODEL NUMBER 500R TT(96093000100), PR ODUCT NUMBER 960 93 00-01 HANDLE ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 21 532 18 11-27 Handle 23 532 08 67-77 Screw , He x W asher Hd.
20 KEY P ART NO . NO . DESCRIPTION 1 873 51 05-00 Nut, K eps 5/16-18 2 810 04 06-00 W asher , Lock 3/8 3 873 22 06-00 Nut, Hex 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard RT 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Lev er , Shift 7 872 11 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
21 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P AR TS TILLER - - MODEL NUMBER 500R TT(96093000100), PR ODUCT NUMBER 960 93 00-01 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Locknut, He x, Flange 5/16-18 5 532 10 23-32 Brack et, Reinf orcement 7 532 10 21-73 Counter Weight, R.
22 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 31 7 6 5 4 11 10 29 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .
23 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 11 12 16 11 12 25 33 32 16 3 4 7 8 9 5 23 23 28 24 18 6 5 5 12 11 10 tine_shield_13_in 22 21 20 19 1 19 532 10 27-01 Gr ip 20 873 22 06-00 Nut, Hex 3/8-16 21 532 10 21-56 Stake, Depth 22 874 93 06-32 Bolt, Hex 3/8-16 x 2 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
24 2 11 11 10 9 9 4 4 5 34 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 00 44-59 Tine, Outer , L.H. 2 532 13 26-73 Clevis Pin 3 532 00 65-54 Tine, Inner , L.H. 4 532 12 46-60 Retainer , Spring Zinc 5 532 13 27-27 Assembly , Hub and Plate , L.
25 1 532 18 92-32 Decal, Blt Grd 2 532 18 92-35 Decal, Logo 3 532 18 61-77 Decal, CNTRL PNL 5 532 11 06-14 Decal, Hand Placement 6 532 10 21-80 Decal, Shift Indicator 7 532 16 23-84 Decal, W ar ning 8 532 18 92-33 Decal, Tineshield 9 532 12 00-76 Decal, W ar ning, Rotating Tines - - 532 19 42-46 Manual, Owner’ s (English) KEY P ART NO .
26 SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original pur- chaser to be free from defects in material and workmanship from.
27 SER VICE NO TES.
532 19 42-46 11.10.04 TR Printed in U.S .A..
An important point after buying a device Husqvarna 500RTT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 500RTT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 500RTT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 500RTT you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 500RTT will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 500RTT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 500RTT.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 500RTT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 500RTT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
