Instruction/ maintenance manual of the product 2009-01 Husqvarna
Go to page of 21
Operator's Manual 200 9 -0 1 115145127 Blower Kit - 48" Collection System Operator's Manual 966004501.
CONTENTS CONGRA TULA TIONS on the purchase of a new collection system. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center/ department.
4 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS DANGER ! THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OBJECTS. F AILURE TO OBSER VE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
5 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS DO NOT • Donot turn on slopes unless necessary , and then, turn slowly and gradually downhill, if possible.
6 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before storing. • Stopandinspecttheequipmentifyoustrikean object.
7 UNP ACKING INSTRUCTIONS • Removeallpartsandpackingmaterialsfrom carton. TOOLS REQUIRED • 7 / 16 "Wrenchorratchetandsocket • ½"Wrench.
8 1. Removethedischargechutefromthedeck.(Deck congurationwillvarybysizeandmodel) 2. Lowerdecktothelowestcuttingposition. 3. Removetherighthand(dischargeside)beltcover fromthedeck.
9 ASSEMBL Y 1. Makesurethetensionreleaseleverisforwardor disengaged. 2. Placethebeltoverthepulleyonthedeck.Referto illustration for proper routing. 3. Move the tension release arm to the rear and engage in the latch.
10 2. Install the bagger mount tube to the rear guard with 5 / 16 -18x3¼boltsandangenutsfromkit. NOTE: Depending on model, rear guard hole may need to be drilled out to 5 / 16 "ifkithardwareistoo large.
11 1. Position upper chute support against bagger inlet, fl ush at outer edges. See Illustration. 2. Using support as a template, drill two 3 / 8 holes into bagger hood. Upper Chute Support Bagger Inlet Nut Bagger Hood Flat W ashers Hex Bolt Flex T rim 3.
12 Remove plastic end caps from the center two bag 1. support arms. Fully insert spacer plugs into the ends of the support tubes. It may be necessary to tap the spacers into place with a hammer or mallet.Replacetheplasticendcapbackoverthe spacer .
13 • Ifthegrasscatcherfailstopickupcutgrass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. a. Disengage blades, place motion control levers in neutral position.
14 4 5 7 8 9 10 11 13 14 T orque to 30 ft/lbs 15 16 17 18 19 20 21 22 23 39 26 25 29 30 38 28 24 1 2 3 6 10 12 14 15 23 33 34 35 36 31 44 32 37 44 43 11 40 47 48 50 51 52 53 51 42 45 46 27 49 48 41 45.
15 539 101977 1.. .... 1 .... TRACTION SPRING 539 976952 2.. .... 1 .... SCREW 10-24 x .625 RD 539 10441 1 3.. .... 1 .... KNOB W/STUD 539 104763 4.. .... 1 .... RET AINER U TYPE 539 105785 5.. .... 1 .... DECAL, W ARNING 539 106741 6.. .... 1 .... DECAL, SEVERING 539 108084 7.
16 6 5 4 4 3 3 1 9 2 12 10 7 8 11 Chute Assembly REP AIR P AR TS.
17 539 108081 1.. .... 1 .... SCREW , SPEC 10-14 x ½ 539 108082 2.. .... 1 .... INDICA T OR, BAG DUMP 539 108083 3.. .... 2 .... SCREW 10-24 x 1 1 / 8 539 108084 4.. .... 3 .... W ASHER 3 / 16 x ¾ 539 108085 5.. .... 2 .... SP ACER, SPLIT 539 108086 6.
18 REP AIR P AR TS 26 25 19 18 14 21 27 7 6 10 13 12 16 17 22 4 2 3 1 5 11 24 15 24 20 23 8 24 28 15 24.
19 ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION REP AIR P AR TS 539 1 1 1587 1.. .... 1 .... WEIGHT PLA TE 522 923202 2.. .... 2 .... WEIGHT BRACKET 521 996501 3.. .... 8 .... NUT 3 / 8 -16 HEX FLANGE 539 108271 4.. .... 4 .... HCS 3 / 8 -16 x 3½ 539 101341 5.
SECTION 1: LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that t.
† Refer to Section 3 for items not covered by this warranty *All consumer product use must have been limited to the owner s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use.
P/N 1 15 145127 IR 01/22/09.
An important point after buying a device Husqvarna 2009-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 2009-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 2009-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 2009-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 2009-01 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 2009-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 2009-01.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 2009-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 2009-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
