Instruction/ maintenance manual of the product 170BT Husqvarna
Go to page of 16
W ARNING Before using our product s, please read this manual caref ully to understand the pr oper use of your unit . APPLICABLE SERIA L NUMBERS: 6020010 1 and up Operator’ s manual 170BT English 1 1.
English 2 EC-dec lar ation of conf or mity (Applies to Euro pe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, decla res under sole respo nsibility that the blowers Husqvarna 170 B.
English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
English 4 SAFETY FIRST Instructions contained in warn ings within this manual and warning seals marked with a symbol on the blower concern critical points which must be tak en into consideration to prevent possible serious bodily injury , and for this r eason you are requested to read all such instruct ions carefully and follow them without fail.
English 5 For safe operation and mainten ance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake.
English 6 WORKI NG CONDITIONS 1. Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. T o reduce the risk of hearing loss associated with sound levels, hearing protection is required.
English 7 W ARNING Check to see if the shock- absorbing rubber mount has beco me cracked or otherwise damaged. Note that failing to replace this rubber mount when it has become cracked or damaged m ay cause the engine to com e loose from it s frame during use, th us resulting in possible serious bodily injury .
English 8 1. Frame 2. Shoulder S trap 3. S park Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. V olute Case 9. “CAUTION” Label 10.Elbow 1 1. Fuel T ank 12.Recoil Starter 13.Ignition Sw itch 14.Engin e Cover 15.Handle Bar ( Accessory) 16.
English 9 * The data shown above are th ose in the case of one straight pipe. * S pecifications are subject to change without notice. MODEL 170BT Dimensions (L x W x H) mm (in) 365x464x485 (14x18x19) Dry Weight kg (lbs) (including pipe) 12 (26.5) (total weight) Fuel T ank Capacity liter (fl.
English 10 SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied wit h the unit. THRO TTLE LEVER 1. Set up the throttle holder to the swiv el and tigh ten the screw on the holder.
English 11 HARNESS NOTE The harness must always be wo rn when working with the ma chine. Failure to do so means you will be unable to ma neuver safely and this can result in injury to yoursel f or others . A correctly adjusted harness and machine signifi cantly facilitates the work.
English 12 FUEL W ARNING • Gasoline is very flammable . A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allo w it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10ft (3m) away from the fueli ng point before starting the engine.
English 13 ST ARTING ENGINE IMPORT AN T • Avoid operating the blower with the flexible tube and swiv el joint disconnected. That will redu ce the cooling air and the eng ine could be damaged by overheat ing. 1. Push the primer bulb until fuel flows out in the clear tube.
English 14 Maintenance, replacement, or repair of the emission contro l device and systems may be perform ed by any non-road eng ine repair establishment or individual. W ARNING Make sure that the engine has stopped and is cool before performing any service to the blower.
English 15 SP ARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electr odes as necessary with a wire brush. The spark gap should be adjusted to .
English 16 IGNITION COIL AIR GAP INSPECTION • If the gap is not accurate or when installing the co il or rotor , adjust the air gap between the ignition coil and the iron core of the rotor . Air Gap: 0.40mm (0.35 to 0.45mm) 0.016 in (0.014 to 0.
An important point after buying a device Husqvarna 170BT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 170BT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 170BT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 170BT you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 170BT will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 170BT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 170BT.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 170BT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 170BT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
