Instruction/ maintenance manual of the product 15T AWD Husqvarna
Go to page of 40
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 15T Rider 15T AW D Rider 15Ts A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.
2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ......
English – 3 Ser vice journal Pre-deliver y service 1 Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure (60 Kpa, 0.6 bar , 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.
4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency e ven in small or confined areas.
English – 5 KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
6 – English KEY T O SYMBOLS Chec k the engine’ s oil lev el Check tr ansmission oil lev el Lift up the cutting unit Apply the parking brake . If the engine is cold, use the choke Release the parki.
English – 7 WHA T IS WHA T? What is what on the ride-on mo wer 1 Choke control 2 Switch f or the lights 3 Throttle control 4 Ignition lock 5 Counter 6 Cutting height adjustment le ver 7 Lifting le v.
8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are f or your saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider.
English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hear ing protection to minimise the risk of hear ing impairment.
10 – English SAFETY INSTR UCTIONS • F ollow the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability . Children • Serious accidents may occur if y ou f ail to be on your guard f or children in the vicinity of the machine.
English – 11 SAFETY INSTR UCTIONS • Do not change the setting of gov ernors and avoid running the engine at e xcessively high re vs. If you run too fast, y ou risk damaging the machine components. • Nev er use the machine indoors or in spaces lacking proper ventilation.
12 – English PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 15T , Rider 15Ts A WD and Rider 15T A WD . The machines are equipped with chronometer and lights.
English – 13 PRESENT A TION Cutting unit Rider 15T , Rider 15T A WD and Rider 15Ts A WD can be equipped with three diff erent cutting units. • CombiClip 94 • CombiClip 103 • CombiClip 112 The Combi-unit, equipped with a BioClip-plug, finely chops the cuttings to f er tiliser .
14 – English PRESENT A TION T o adjust mo ve the le ver under the front edge of the seat to the left, so that the seat can be mov ed f orward or bac kwards to the required position. Fuelling The engine runs on unleaded petrol with a minimum octane rating of 87 (not mix ed with oil).
English – 15 Driving Bef ore star ting • Read the safety instructions and information concer ning the placement of controls and functions bef ore star ting. • Perf or m daily maintenance before starting as set out in the Maintenance schedule. Star t the engine 1 Make sure that the clutch control is depressed.
16 – English Driving 8 Let the engine run at moderate speed or half throttle for 3- 5 minutes bef ore subjecting it to heavy load. 9 Set the required engine speed with the throttle control. Star ting the engine with a weak battery If the batter y is too weak to star t the engine, it should be recharged.
English – 17 Driving 4 Press in the lock b utton on the lifting le ver and lo wer the cutting unit. Cutting tips • Localise and mark stones and other fixed objects to a void collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained.
18 – English Maintenance Maintenance schedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) If the machine is used daily it should be lubricated twice a week.
English – 19 Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure.
20 – English Maintenance 2 Check the tension of the steering wires by squeezing them together by the arro ws as illustrated. It should be possible to push them together so that the distance between them is half as much, without using unnecessary f orce.
English – 21 Maintenance Checking and adjusting the c hoke wire If the engine is producing blac k smoke or is difficult to start then the choke wire (upper wire) ma y be incorrectly adjusted.
22 – English Maintenance 6 If the paper filter is still dir ty it should be replaced with a new one . Alwa ys replace the paper filter ev er y 200 hours.
English – 23 Maintenance Check the saf ety system The machine is equipped with a saf ety system that pre vents star ting or driving under the following conditions . The engine should only be possible to start when the cutting unit is in its raised position and the h ydrostat pedals are in the neutral position.
24 – English Maintenance Replacing the light bulbs F or information about the bulb type , see T echnical Data. 1 Loosen the lock n ut and remov e the Allen bolt. Remov e the steering wheel. 2 Unscrew the tw o screws holding the co ver on the po wer ser vo housing.
English – 25 Maintenance Open the engine co ver. Check that the cooling intak e is free from leav es, grass and dir t. Check the air duct, located on the inside of the engine co ver , ensure it is clean and does not rub against the cooling air intake .
26 – English Maintenance 9 Hook up the height adjustment strut. 10 Secure the collet spring. 11 Fit the front cov er . Removing the cutting unit 1 Carr y out points 1-6 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit.
English – 27 Maintenance Checking the cutting unit’ s parallelism Check the cutting unit’ s parallelism as f ollows: 1 Check the air pressure in the tyres 60 kP a/0.6 kp/cm 2 /8.5 PSI. 2 Place the machine on a flat surf ace. 3 Put the lifting le ver in the mo wing position.
28 – English Maintenance 7 Remov e the screws on the cutting co v er . Lift the unit frame and remov e the cutting unit cover . 8 Loosen the spring that tensions the V -belt and pr y off the belt.
English – 29 Maintenance Restoring fr om service position 1 Grip the front edge of the unit and loosen the lock, f old down and slide in the unit. 2 Replace the cutting height sta y and the belt. 3 T ension the belt with the belt adjuster . 4 Fit the front cov er .
30 – English Lubrication Checking the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again, without tightening it.
English – 31 Lubrication Lightly lubricate the r ubber seal on the ne w oil filter using new oil. Fit the oil filter by turning clockwise. T urn by hand until the rubber seal is seated. Now tighten a fur ther half tur n. Fill with new oil according to Chec king the engine’ s oil lev el.
32 – English T roub leshooting sc hedule Prob lem Procedure Engine does not star t There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir .
English – 33 Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine.
34 – English T echnical data Note 1: The power r ating of the engine indicated is the av erage net output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may diff er from this value.
English – 35 T echnical data Cutting unit CombiClip 94 CombiClip 103 CombiClip 112 Cutting width, mm/inch 940/37 1030 / 41 1120 / 44.1 Cutting heights, 7 positions , mm/inch 25-75/0.98-2.95 25-75/0.98-2.95 25-75/0.98-2.95 Blade length, mm/inch 358/14.
36 – English T echnical data EC-declaration of conf ormity (Applies to Europe onl y) Husqv arna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 15T , R.
.
´®z+U+r¶6§¨ ´®z+U+r¶6§¨.
.
´®z+U+r¶6§¨ 2010-03-24 ´®z+U+r¶6§¨ 1153118-26 Original instructions.
An important point after buying a device Husqvarna 15T AWD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 15T AWD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 15T AWD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 15T AWD you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 15T AWD will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 15T AWD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 15T AWD.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 15T AWD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 15T AWD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
