Instruction/ maintenance manual of the product 1153191-26 Husqvarna
Go to page of 24
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 356BT X-series Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.
2 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets .
KEY T O SYMBOLS English – 3 Symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
CONTENTS 4 – English Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . Husqvarna AB has a policy of continuous product dev elopment and therefore reserves the right to modify the design and appearance of products without prior notice.
SAFETY INSTR UCTIONS English – 5 P ersonal pr otective equipment • Glov es should be wor n when necessary . • Wear hearing protection that provides adequate noise reduction. • Alwa ys wear approved e ye protection. If you use a visor then you must also w ear approved protectiv e goggles.
SAFETY INSTR UCTIONS 6 – English Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimize vibration and mak e operation easier . Muffl er The m uffler is designed to keep noise le vels to a minimum and to direct exhaust fumes a way from the user .
SAFETY INSTR UCTIONS English – 7 Vibration damping system • Check the vibration damping units regularly f or cracks or deformation. Replace them if damaged. • Check that the vibration damping element is undamaged and securely attached. Muffl er • Nev er use a machine that has a faulty muffler .
SAFETY INSTR UCTIONS 8 – English Starting • Nev er star t the machine indoors. Exhaust fumes can be dangerous if inhaled. • Observe the surroundings and ensure that no people or animals can come into contact with the blow er.
SAFETY INSTR UCTIONS English – 9 Place the hip strap ov er the hip and not too far down on the stomach. Tighten the hip strap so that you feel the weight of the blo wer resting on your hip .
SAFETY INSTR UCTIONS 10 – English Basic working tec hniques • The speed of the air jet is regulated by means of the throttle. Select the speed best suited f or respective tasks. Y ou can set the throttle position using the ”stop switch” and by doing so not need to hold y our finger on the throttle all the time you are using the b lower .
English – 11 WHA T IS WHA T? What is what on the blo wer? 1 Outer cov er 2 Harness 3 Outlet pipe 4 Bellows with guard 5 Stop switch with throttle position setting 6 Control handle/Operating handle 7.
ASSEMBL Y 12 – English Assembling the blo w pipe and control handle • Loosen the two screws on the f an’ s outlet pipe and remov e the two wear ring halves located on the outlet pipe. • Place these on the pipe bend so that the guide on the wear ring halves aligns with the slot on the pipe bend.
ASSEMBL Y English – 13 Accessories Handlebar Disassemble the intermediate pipe. Disassemble the knob from the holder and puch the holder on to the holder pipe. Assemble the knob and tighten. Assemble the intermediate pipe. Flat nozzle • If higher air speed is required, the round blow pipe is replaced by the flat nozzle.
FUEL HANDLING 14 – English Fuel CA UTION! The machine is equipped with a tw o-stroke engine and must alwa ys been run using a mixture of petrol and two-stroke oil. It is impor tant to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.
FUEL HANDLING English – 15 Fuelling • Mov e the machine at least 3 m from the refuelling point before starting it. • Clean the area around the fuel cap. Contamination in the tank can cause operating problems . • Ensure that the fuel is well mix ed by shaking the container before filling the tank.
ST ARTING AND ST OPPING 16 – English Starting and stopping Cold engine Ignition: Set the stop s witch to the star t position. Star t position is achiev ed by moving the stop s witch slightly backwards until the stop s witch clicks into start position.
MAINTENANCE English – 17 Carburettor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.
MAINTENANCE 18 – English Loosen the muffler’ s 2 screws and remov e the muffler . Pull out the spark arrestor mesh and clean using a wire brush. Replace the spar k arrestor mesh if it is defectiv e. CA UTION! Ne ver use a machine with a def ective muffler .
MAINTENANCE English – 19 Clean the filter ev er y 40 hours, or more regularly if conditions are exceptionally dusty . A void contact with hot surfaces on m uffler, cylinder etc. Contact can result in burns to the skin. Cleaning the air filter Dismantle the outer cov er with the help of the four fasteners holding the outer co ver .
MAINTENANCE 20 – English Maintenance schedule Below you will find some gener al maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1 Clean the outside of the machine. 2 Check that the throttle control functions saf ely .
English – 21 TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/ EC. Repor ted sound power lev el for the machine has been measured with the original cutting attachment that gives the highest lev el.
22 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Europe onl y) Husqv arna AB, SE-561 82 Huskv ar na, Sweden, tel +46-36-146500, declares under sole responsibility that the bl.
.
Original instructions ´®z+U3,¶6;¨ ´®z+U3,¶6;¨ 2010-05-18 1153191-26.
An important point after buying a device Husqvarna 1153191-26 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 1153191-26 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 1153191-26 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 1153191-26 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 1153191-26 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 1153191-26, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 1153191-26.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 1153191-26. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 1153191-26 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
