Instruction/ maintenance manual of the product 1130 SBEXP Husqvarna
Go to page of 32
1130SBEXP Owner's Manual.
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 26 Ounces Spark Plug: Champion RN4C (Gap: .030") CONGRA TULA TIONS on your purchase of a new snow thrower .
4 P ARTS P ACKED SEP ARA TEL Y IN CART ON.
5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 ASSEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.
7 ASSEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinfl ated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI (19-24.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 DEFLECTOR REMOTE CONTROL LEVER TRACTION DRIVE CONTROL LEVER DISCHARGE CHUTE CONTROL LEVER RECOIL (AUXILIARY) ST ARTER HANDLE THROTTLE / ENGINE CONTROL DRIVE SPEED CON TROL LEVER AUGER CONTROL LEVER .
10 OPERA TION TO CONTROL SNOW DISCHARGE (See Fig. 14) W ARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
11 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system.
12 TO ADJUST SKID PLA TES (See Fig. 19) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
13 TO ST ART ENGINE • Be sure fuel shut-off valve is in the OPEN position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A.
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE SNOW THROWER Always observe safety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (14–17 P .
16 SER VICE AND ADJUSTMENTS W ARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped.
17 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 24) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center .
18 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 6 6 6 5 9 12 7 8 6 11 27 57 10 10 10 13 4 14 16 15 36 37 50 47 42 42 44 .
21 KEY P ART NO. NO. DESCRIPTION 1 532 18 86-63 Bar , Weight 2 532 16 67-85 Nut, Hex 5/16-18 3 872 1 1 05-10 Bolt, Carriage 5/16-18 x 1-1/4 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Asse.
22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 3 2 1 2 6 19 2 2 26 28 27 27 25 20 29 31 30 7 4 5 6 8 8 16 18 17 10 14 3 1.
23 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 KEY P ART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Sc.
24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 41 27 22 17 11 15 15 14 38 39 40 37 33 35 35 .
25 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 4 4 4 1 2 5 3 5 1 2 3 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 3 42 42.
27 KEY P ART NO. NO. DESCRIPTION 1 532 14 63-15 Screw , Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15 Washer , Flat 4 817 49 05-08 Screw , Hex Head 5/16-18 x 1/2 5 532 18 00-1.
28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 6 20 14 47 47 48 4.
29 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 KEY P ART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, T raction Idler 2 532 18 05.
30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 7 32 30 32 30 15 18 17 19 13 20 11 27 27 19 16 20 11 14 15 12 13 18 14 12 4 4 31 34 34 2 8 .
31 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 1130SBEXP (96193000600), PRODUCT NO. 961 93 00-06 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
532 19 83-81 Rev . 5 05.25.06 BY Printed in U.S.A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur- c.
An important point after buying a device Husqvarna 1130 SBEXP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 1130 SBEXP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 1130 SBEXP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 1130 SBEXP you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 1130 SBEXP will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 1130 SBEXP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 1130 SBEXP.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 1130 SBEXP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 1130 SBEXP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
