Instruction/ maintenance manual of the product 82004 Hunter Fan
Go to page of 28
Installation Guide 82004 Orleans Bath Ventilator with Light READ and SAVE THESE INSTR UCTIONS 41946-01 3/29/2006 ENGLISH See page 2 ESp añoL Vea la página 15 05-HF-017-EngS_3.
2 DISCONNECT ELECTRIC POWER SUPPL Y AND LOCK OUT SERVICE P ANEL BEFORE SERVICING UNIT W arning TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY , OBSERVE THE FOLLOWING: 1. For general ventilating use only . Do not use for ventilat- ing hazardous or explosive materials.
3 1 T urn off the power source. T ools Needed. (Not supplied.) Estimated assembly time: 30 to 60 minutes Before Installation x2 3/8” Cable Connector H I J K L x4 * * * NO TE: Strain relief cable connector must be installed.
5 4 7 G 8 F Remove the motor/blower from the housing. 4 H E 3 Remove the pre-loaded screw tip co vers. Remove the wiring cover screw . 6 Back out the pre-loaded screw tips until flush with the side of the housing. Remove the wiring cover . Remove packing material.
9 E Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and secure with washer . Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock.
A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground A 1 4 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option A 1 3 Route wires through the strain relief. Connect wires as shown.
A 1 9 I Secure the motor by tightening the 2 screws. A2 0 T urn on the power source. 7 Connect wiring harness. DO NOT ALLOW THE MO TOR TO HANG FROM THE WIRING HARNESS. 0 0 0 0 0 0 0 0 A 1 7 Reinstall the motor by inserting the tabs and pushing up into position.
EXISTING F AN B 1 1 E B 1 2 Existing Construction B 1 3 2 1 B 1 4 Route wires through strain relief . Remove an existing fan and check to make sure the open- ing is large enough to accommodate the new motor hous- ing (7 1/4”x 7 3/4”). Move the housing into position abo ve the ceiling.
A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground B 1 6 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option H B 1 8 H B 1 9 B 2 0 I Connect wires as shown. Reinstall the motor by inserting the tabs and pushing up into position.
O N O F F B 2 2 B 2 3 C1 Go to step on page 10 to attach grille . B 2 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. Attaching the Grille Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS.
NOTE: Remove plastic packaging material from glass dome. Align glass dome and push up. Install 2 Max 60 watt A-15 bulbs (Not Included). C 7 M Screw finial into position. C 5 C 6 L Attach thumbscrews. WARNING: T o reduce the risk of electrical shock, all 3 thumbscrews MUST be properly installed.
T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. T o confirm that the fan is running, place your hand near the vents to feel the air movement. • T urn power on, replace fuse, or reset breaker .
W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warr anty to the original user or consumer purchaser of this Hunter bath exhaust fan: If .
2500 Frisco Avenue, Memphis, T ennessee 38114 Printed in China 41946-01 3/29/2006 14 © 2006 Hunter Fan Company 05-HF-017-EngS_3.29.06.indd 14 3/29/06 6:55:11 PM.
DESDE Guía de instalación V entilador para baño Orleans 82004 con luz LEA y CONSERVE EST AS INSTRUCCIONES 41946-02 3/29/2006 Esp añol 15 05-HF-017-Sp_3.
16 41946-02 3/29/2006 41946-02 3/29/2006 DESCONECTE LA ALIMENT ACIÓN ELÉCTRICA Y CIERRE EL P ANEL DE SERVICIO ANTES DE DAR MANTENIMIENTO A LA UNIDAD tc.
x2 H I J K L x4 * * A B C 95261-01-000 74508-03-133 96382-01-444 75184-01-133 96456-01-444 M 75730-01-444 x2 D Conector de cable de 3/8” * NO T A: Debe estar instalado el manguito de alivio de tensión del cable.
5 4 7 G 8 F 18 H E 3 6 Retire el motor/soplador del alojamiento. Retire las cubiertas de las puntas de tornillo precargadas. Retire el tornillo de la cubierta del cableado. Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento.
9 E 19 1 0 B C A 1 1 E 5/8 1/2 5/8 1/2 A 1 2 Retire el primer tapón metálico de acceso del cableado. Utilice el segundo si es necesario. Inserte el manguito de alivio de tensión (no se inc luye) en la caja y sujételo firmemente con una arandela.
A Motor del ventilador Luz Verde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Blanco Negro Luz Blanco Blanco Cobre desnudo Tierra A 1 4 *Opción Ventilador y luz principal juntos *Opción Negro 3 pasadores 3 clavijas 2 pasadores 2 clavijas A 1 3 0 0 A 1 6 20 A 1 5 E F G Tienda los cables a través del manguito de alivio de tension.
A 1 9 I A2 0 21 0 0 0 0 0 0 0 0 A 1 7 0 0 0 0 0 0 0 0 H A 1 8 E N C E N D I D O A P A G AD O A 2 1 A2 2 C1 Vaya al paso en la página 24 para fijar la rejilla. Asegure el motor apretando los 2 tornillos. Encienda la fuente de alimentación. Conecte el mazo de cables.
VENTILADOR EXISTENTE B 1 1 E B 1 2 B 1 3 2 1 B 1 4 E B 1 5 Construcción existente Tienda los cables a través del manguito de alivio de tension. Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (7 1/4” x 7 3/4”).
A Motor del ventilador Luz Verde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Blanco Negro Luz Blanco Blanco Cobre desnudo Tierra B 1 6 *Opción Ventilador y luz principal juntos *Opción Negro 3 pasadores 3 clavijas 2 pasadores 2 clavijas H B 1 8 H B 1 9 B 2 0 I F B 1 7 G Conecte los alambres como se muestra.
E N CE ND ID O A P AG AD O B 2 2 B 2 3 C1 Vaya al paso en la página 24 para fijar la rejilla. B 2 1 Fijación de la rejilla Retire los tornillos de mano. Conecte el mazo de cables. NO PERMIT A QUE EL MOTOR CUELGUE DEL MAZO DE CABLES. K C 1 H C 2 J Pruebe el motor .
NOT A: Retirar material plástico de empaque de la pantalla. Alinee de la pantalla y levante. Instale 2 bombillas A-15 de 60 vatios como máximo (No incluidas).
Solución de problemas Problema: El ventilador no está operando. Solución: • Los ventiladores de baño Hunter son muy silenciosos. Para confirmar que el ventilador esté funcionando, coloque su mano cerca de los conductos de ventilación para sentir el movimiento del aire.
41946-02 3/29/2006 41946-02 3/29/2006 27 Garantía Hunter Fan Company Extractor de aire para baño GARANTÍA LIMIT ADA Hun ter Fan Co mpan y e stab lec e l a si gui ent e ga ran tía li mita da al u s.
2500 Frisco Avenue, Memphis, T ennessee 38114 Impreso en China 41946-02 3/29/2006 © 2006 Hunter Fan Company 05-HF-017-Sp_3.29.06.indd 28 3/29/06 6:56:04 PM.
An important point after buying a device Hunter Fan 82004 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan 82004 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan 82004 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan 82004 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan 82004 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan 82004, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan 82004.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan 82004. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan 82004 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
