Instruction/ maintenance manual of the product 7430.821 American Standard
Go to page of 8
1 2 5 4 GROOVE (FAUCET BASE) MOUNTING SURFACE 3 8 Figure A M968640 REV.1.1 7430.821 7430.801 7431.821 7431.801 Cer tified to comply with ANSI A112.18.
2 1 VAL VE OUTLET SUPPL Y CONNECTION 3 RED BAND BLUE BAND Connect Red Banded Hose to Left V alve and Blue Banded Hose to Right V alve. Attach COUPLING NUTS (1) of SUPPL Y HOSES (2) and tighten making water tight connection. Important: Loop SUPPL Y HOSES (2) as illustrated so they do not kink.
M968640 REV.1.1 3 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY.
M968640 REV.1.1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
M968640 REV.1.1 5 T o change direction of handle rotation, proceed as follows: T urn valve to OFF position. Thread counter-clock wise HANDLE BASE (1) to remove HANDLE ASSEMBL Y (2) from ESCUTCHEON BASE (3) . Use a flat blade screw driver to remove SPRING CLIP (4) .
M968640 REV.1.1 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration.
M968640 REV.1.1 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper.
M918462-0070A CABLE ADAPTER M968640 REV.1.1 8 M962831-YYY0A LEFT LEVER HANDLE ASSEMBL Y BER WICK ™ / BOULEV ARD ™ SPREAD LA V A TORY FITTING MODEL NUMBER M962837-YYY0A CROSS HANDLE ASSEMBL Y M9628.
An important point after buying a device American Standard 7430.821 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Standard 7430.821 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Standard 7430.821 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Standard 7430.821 you will learn all the available features of the product, as well as information on its operation. The information that you get American Standard 7430.821 will certainly help you make a decision on the purchase.
If you already are a holder of American Standard 7430.821, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Standard 7430.821.
However, one of the most important roles played by the user manual is to help in solving problems with American Standard 7430.821. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Standard 7430.821 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
