Instruction/ maintenance manual of the product 6065.26X American Standard
Go to page of 14
Installation Instr uctions Installation Instr uctions (In T oronto Area onl y: 1 -905-3061 093) Certified to comply with ASME A112.19.2M © 20 1 0 AS America, Inc. NO TE T O INST ALLER: Please giv e this manual to the cust omer af ter installation. SELECTRONIC™ PROXIMITY TOILET CONCEALED FLUSH V AL VE 1.
All American Standar d Products Are W ater T ested At Our Factory . Some Residual Wat er May R emain In The V alve Dur ing Shipping. T hank you for selecting American-Standar d...the benchmark of f ine qualit y f or over 1 00 years. T o ensure that your installation pr oceeds smoothly --please read these instructions c arefully bef ore you begin.
RECOMMENDED T OOLS; F ig. 2 F ig. 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10 . T eflon T ape Flat Blade Scre wdriver Adjust able W rench T ape Measure Hacksa w T ubing Cutt er File F or Sweat C onnection; Solder and T orch 2.
F ig. 4 Fig. 3a F ig. 5 3 INS T ALL ELECTRIC AL BO X A SSEMBL Y ; F ig. 3 1. Cut a 1 27x1 27mm (5"x 5") opening in finished wall f or ELECTRIC AL BO X (1) at the deminsion shown in F ig.3. 2. Rot ate the 4 MOUNTING T ABS (2) flat against the electrical bo x.
4 F ig. 6 F ig. 6a F ig. 6b F ig. 6c 3 4 INS T ALL V A CUUM BREAKER AND FLUSH CONNECTIONS; Fig. 6 4 1. Place the SPUD FLANGE (1) over the spud on the F ixture . Fig. 6. 2. Thread SPUD COUPLING NUT (2) ont o Spud. Make sure SEAL W ASHER (4) and FRICTION W ASHER (3) are inst alled.
7 9 6 2 5 8 10 F ig. 9 F ig. 8 5 7 1. Inser t the side ADJUS T ABLE T AILPIECE (1) on the FLUSH V AL VE (2) int o the SUPPL Y ST OP (3) . Lubricate the T AILPIECE O-RING (4) with w ater if necessar y . Lightly tighten COUPLING NUT (5) . F ig. 8. Important: Do not use lubricants (other than w ater) or any type of thread sealing past e or tape .
11 6 1. Remo ve the f our CO VER SCREWS (1) and CO VER from (2) ELECTRIC AL BO X (4) . F ig. 1 0. 2. P ull the CIRCUIT BO ARD (3) out from ELECTRIC AL BO X (4). Fig. 1 0. 3. Knock out lo wer blank in ELECTRIC AL BO X (4) with flat blade sc rewdr ive r .
TOP 1. Remo ve the f our CO VER SCREWS (1) and CO VER (2) from ELECTRIC AL BO X (3) . F ig. 1 0. 2. Install BA TTER Y (4) into holder on DC cir cuit board. P ress BA TTER Y (4) down (contacts f acing down ward) in to position until tabs loc k BA TTER Y (4) into place .
8 1 4 2 5 5 6 BLUE HOSE BLACK HOSE 1. P ush the BLACK HOSE (1) int o the BO TTOM HOSE CONNECT OR (2) and the other end into the back of the O VERRIDE SWITCH (3) . 2. P ush the BLUE HOSE (4) into the TOP HOSE CONNECT OR (5) on the valv e and the other end into the BO TT OM CONNECTOR (6) on the O VERRIDE SWITCH (3) .
FOR A C-VERSION (MUL TI HOOK-UP); F ig. 1 5, 1 5a Unit #1 Unit #1 Unit #2 Unit #3 1 . Remo ve the CO VER SCREWS (1) and CO VER (2) from each ELECTRIC AL BO X (3) . 2. See AC V ersion Electrical Hook-up f or Unit #1 of the Multi hook-up . 3. Install SENSOR WIRE GROMMET (4) and FLUSH V AL VE SENSOR WIRE (5) into the CO VER (2) of each unit.
3 5 7 6 TOP 1. R emov e FRONT P ANEL. For remo ving front panel see Step 9 f or instr uctions . 2. Remo ve the f our CO VER SCREWS (1) and CO VER (2) from ELECTRIC AL BO X (3) . F ig. 1 6. 3. Disconnect GREY SENSOR WIRE (4) from CIRCUIT BOARD (5) . 4.
6 TOP 11 Note: T he detection distance is pr eset and is ideal for most installations . Should an adjustment be requir ed f ollow the steps below . 1. Remo ve FR ONT P ANEL (1) . Se e Step 9 for remo ving front panel instr uctions . 2. Remo ve the f our CO VER SCREWS (2) and CO VER (3) from ELECTRIC AL BO X (4) .
12 IS ST OP V AL VE OPEN? L OOK FOR REPEA TED DOUBLE FLASH ON SENSOR YES INST ALL NEW B A TTER Y TR Y MANU AL V AL VE BUTT ON; WILL THE UNIT FLUSH? NO REPLA CE PIST ON KIT INST ALL NEW B A TTER Y or P.
SELECTRONIC™ PROXIMITY TOILET CONCEALED FLUSH V AL VE 1.28 & 1.6 GPF 13 A950223-0071600A SENSOR FOR FLUSH V ALVE WITH 1.6 gpf A950223-0071280A SENSOR FOR FLUSH V ALVE WITH 1.
An important point after buying a device American Standard 6065.26X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Standard 6065.26X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Standard 6065.26X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Standard 6065.26X you will learn all the available features of the product, as well as information on its operation. The information that you get American Standard 6065.26X will certainly help you make a decision on the purchase.
If you already are a holder of American Standard 6065.26X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Standard 6065.26X.
However, one of the most important roles played by the user manual is to help in solving problems with American Standard 6065.26X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Standard 6065.26X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
