Instruction/ maintenance manual of the product HTN40 Hotpoint
Go to page of 16
C OOKER HOOD USER HANDBOOK FOR INST ALLA TION AND OPERA TION MODEL HTN40.
U sing your new C ooker Hood is very simple. Nevertheless, to get the best results it is important that you read this handbook thoroughly before installing and using your appliance for the first time . Electrical Requirements Any permanent electrical installation must comply with the latest I.
3 Co n t ents P age Electrical Requirements 2 G et to know your C ooker Hood 4 Installing your C ooker Hood 5-9 Installation for Recirculation Installation for Extraction Mounting Height Mounting betw.
G et to know your C ooker Hood . 4 Unpacking Before installation, ensure that y ou have r emoved all packing pieces. Dimensions Height 400mm (15 3 / 4 in) Width 600mm (23 5 / 8 in) D epth adjustable from: 270mm (10 5 / 8 in) up to 460mm (18in), excluding the decor panel thickness.
Installing y our C ook er Hood 5 Y our new Cooker Hood can be installed either f or recirculation or extraction through an outside wall. (All fitting supplied) Installation for Recircula tion: If it is not possible to exhaust to the outside, the hood can be used to filter and recirculat e the air (Fig .
Installing y our C ook er Hood 6 T op or Rear Extraction C onnect the ducting material onto the flange: blank off the aperture which is not required. T he charcoal filter is not r equired when the hood is installed in the ducting c ycle . To r emove the grille turn the locks (F ig.
Installing y our C ook er Hood 7 MOUNTING Y our Cooker Hood is designed to fit between two wall cupboards 600mm apart and to take a door panel measuring 400mm (min) to 600mm (max) in height, to match .
Installing y our C ook er Hood 8 F ixing the Hood to the C upboards: Place the template on the side of the right cupboard , so that the letter B aligns with the front part of the cupboard (disregard the thickness of the door) and drill two holes 2.5mm diameter at points B1 and B2 (F ig.
Installing y our C ook er Hood 9 F itting the Decor P anel: T he hood is designed to be fully integrat ed into the kitchen by fitting a decor panel onto the visor to match the adjoining kitchen cabinets. To fit the decor panel remov e the complete visor assembly from the hood.
Opera ting y our C o ok er Hood Do ’ s and Don ’ ts T he C ontr ols 10 DO Do take extra care when fr ying. Do k eep the heating areas on your hob co ver ed over with pots and pans etc. when using the hob or Cooker Hood switch (especially if you are using a gas hob).
Ca ring for your C ooker Hood 11 Before doing an y cleaning or replacing the fil- t ers or light bulb , always ensur e that the elec- tricity supply to the Cooker Hood is switched ‘OFF’ . F ilters and their replac ement: THE GREASE FIL TER - Y our Cooker Hood is fitted with a grease filter which absorbs grease, dust etc.
Ca ring for your C ooker Hood 12 Cleaning: T he exterior of the Cooker Hood should be cleaned regularly to keep it looking like new. Wipe over with a soft cloth, wrung out in warm water and dry with a clean sof t cloth. W ear protective glov es. Y ou can use mild non-abrasive cleaners but always read the manufacturer’ s instructions first.
Tr oubleshooting . 13 F irst , don’t panic! T here ma y be nothing wrong at all. Lo ok for y our problem below , then check the things we suggest. More of ten than not, this will give you the answer to your pr oblem, and you’ll be able to carr y on without having t o telephone your Ser vice Office.
14.
15.
Ke y Contacts Ser vice Hotpoint has the largest appliance manufacturer’ s service team in Europe , trained specialists directly employed by us to ensur e your complet e confidence. R epair Ser vice UK: 08709 066 066 Re public of Ireland: 1850 302 200 Y ou will be asked for the following inf ormation:- Name, address and postcode .
An important point after buying a device Hotpoint HTN40 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hotpoint HTN40 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hotpoint HTN40 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hotpoint HTN40 you will learn all the available features of the product, as well as information on its operation. The information that you get Hotpoint HTN40 will certainly help you make a decision on the purchase.
If you already are a holder of Hotpoint HTN40, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hotpoint HTN40.
However, one of the most important roles played by the user manual is to help in solving problems with Hotpoint HTN40. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hotpoint HTN40 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
