Instruction/ maintenance manual of the product HLSI 500GT Hoover
Go to page of 17
User instructions EN HLSI 500GT DISHWASHER ®.
3 CONTENTS Safety advice Setting up, installation W ater softener unit Loading the salt Adjusting the upper basket Loading the dishes Information for test laboratories Loading the detergent T ypes of .
4 Fuses and plugs This appliance should be used only on a socket with a minimum rating of 13 Amp. Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 AST A approved. Any replacement should be exactly the same. If the fuse cover is lost, do not use the plug until it is replaced.
W ater connection IMPORT ANT The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused. ■ Th e inlet and drain hoses can be directed to left or right. IMPORT ANT The dishwasher can be connected to either cold or hot water , as long as it is no hotter than 60 °C.
LOADING THE SAL T ■ On the bottom of the machine there is a container for the salt for regenerating the softener . ■ It is important to use only a salt that is specifically designed for dishwasher .
10 1 3 a b a b 2 ADJUSTMENT OF THE UPPER BASKET If 27 cm to 31 cm plates are normally used, load them onto the lower basket after the upper basket has been placed in its upper position and proceed as detailed below: 1. Pull out the upper basket; 2. Then grasp the basket from both sides and lift it upwards (fig.
12 ■ The lower basket is fitted with a special adjustable central rack (fig. 3 and 4) . This permits stable and optimum loading, even when the size and/or shape of the dishes is non-standard. - POSITION “A” : for a standard load, or one that excludes pans, salad bowls and the like.
15 LOADING THE DETERGENT The detergent IMPORT ANT It is essential to use a detergent that is specifically designed for dishwashers either in powder , liquid or tablet form.
17 1 2 3 CLEANING THE FIL TERS The filter system (fig.A “4”) consists of: a central container that traps the larger particles; a flat gauze that continuously filters the wash water; a micro filter , located beneath the gauze, that traps the tiniest particles ensuring a perfect rinse.
19 WHEN CYCLE IS FINISHED After every wash it is essential to turn off water supply and to switch off the machine by pressing the On/Off button to the of f position. If the machine is not going to be used for some time, it is advisable to follow these rules: 1.
21 20 EN 50242 place load Capacity with pans and dishes W ater supply pressure Fuse Power input Supply voltage 15 9 persons Min. 0,08 - Max 0,8 MPa (see rating plate) (see rating plate) (see rating pl.
23 22 "IMPULSE" programmes The “IMPULSE” programmes use an impluse washing technology , which reduces consumption, noise and increases performances.
25 24 AUTOMA TIC F AUL T SIGNALS T urn off the dishwasher , open the inlet hose and reset the cycle. Check if the drain tube is bent or if the siphon or filters are clogged. If the problem persists, contact Customer Service. Check if the drain tube is bent or if the siphon or filters are clogged.
27 26 PROGRAMME GUIDE W ash with prewash For wash programmes with prewash, it is advisable to add a second dose of detergent (max. 10 g) directly in the machine. 140 • •• • 75°C • • •• • • • •• • • 130 85 75°C 65°C Cycle with alternated action of water jets and steam.
29 IDENTIFYING MINOR F AUL TS Should the dishwasher fail to operate, before contacting the Service Centre, make the following checks: 28 F AUL T CAUSE REMEDY 1 - Machine completely dead 2 - Machine do.
30 This appliance is marked according to the European directive 2002/96/EC on W aste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly , you will help preve.
10.10 - 41034648 - www .graficaestampa.it - Printed in Italy - Imprimé en Italie EN 08705-400600 HOOVER SER VICE FOR YOUR LOCAL ENGINEER PLEASE CALL OUR NA TIONAL NUMBER Areas covered by HOOVER SERVI.
An important point after buying a device Hoover HLSI 500GT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoover HLSI 500GT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoover HLSI 500GT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoover HLSI 500GT you will learn all the available features of the product, as well as information on its operation. The information that you get Hoover HLSI 500GT will certainly help you make a decision on the purchase.
If you already are a holder of Hoover HLSI 500GT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoover HLSI 500GT.
However, one of the most important roles played by the user manual is to help in solving problems with Hoover HLSI 500GT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoover HLSI 500GT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
