Instruction/ maintenance manual of the product 08E55-S01-100H Honda
Go to page of 8
© 1999 American Honda Motor Co., Inc - All Rights Reserved. AII 20465 (9908) 1 of 8 Security Attachment (sold separately): P/N 08E55-S01-100H LED Disarm switch Push nut (for LED) 2-Pin connector INST ALLA TION INSTR UCTIONS 08E55-S01-1H00-91 Accessory Application Publications No.
2 of 8 AII 20465 (9908) © 1999 American Honda Motor Co., Inc - All Rights Reserved. NO TE: The Owner’ s Manual included with the Secur ity Attachment should be placed in the glove box for future ref erence. The Owner’ s Manual included with the Security System should be discarded.
© 1999 American Honda Motor Co., Inc - All Rights Reserved. AII 20465 (9908) 3 of 8 6. Remove the left kick panel (two clips, and slide back while pulling its lower end inside). 7. Remove the upper steering column cover (three screws and six clips). TA B SELF-T APPING SCREWS UPPER STEERING COLUMN CO VER KNEE BOLSTER BOL TS 4.
4 of 8 AII 20465 (9908) © 1999 American Honda Motor Co., Inc - All Rights Reserved. 11. Carefully push the LED terminals into the 2-pin connector from the kit.
© 1999 American Honda Motor Co., Inc - All Rights Reserved. AII 20465 (9908) 5 of 8 Installing the Control Unit SLO T 13. Route the terminal ends of the disarm switch harness through the 12 mm hole you just drilled in the dashboard lower co v er . Secure the disar m s witch on the dashboard lower cover using the 12 mm and washer pro vided.
6 of 8 AII 20465 (9908) © 1999 American Honda Motor Co., Inc - All Rights Reserved. CONTROL UNIT COLLARS 4 x 30 mm BOL TS 20. Remove number 3 fuse from the bottom row of the fuse box. (Discard.) FUSE BO X 21. Push the two fuses from the kit into the number 3 and number 6 slots in the fuse box.
© 1999 American Honda Motor Co., Inc - All Rights Reserved. AII 20465 (9908) 7 of 8 WIRE TIES 23. Locate the 4-pin and 6-pin connectors blue-taped to the vehicle harness behind the fuse box. 24. Locate the 4-pin connector blue-taped to the vehicle harness above the fuse box, and remove the tape to free the connector .
8 of 8 AII 20465 (9908) © 1999 American Honda Motor Co., Inc - All Rights Reserved. DISARM SWITCH 3-PIN CONNECT OR VEHICLE HARNESS 3-PIN CONNECTOR FUSE BO X WIRE TIE CUSHION T APE (half) VEHICLE HARNESS INSPECTION 31. Check that all wire harnesses are routed properly and all connectors are plugged in.
An important point after buying a device Honda 08E55-S01-100H (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honda 08E55-S01-100H yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honda 08E55-S01-100H - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honda 08E55-S01-100H you will learn all the available features of the product, as well as information on its operation. The information that you get Honda 08E55-S01-100H will certainly help you make a decision on the purchase.
If you already are a holder of Honda 08E55-S01-100H, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honda 08E55-S01-100H.
However, one of the most important roles played by the user manual is to help in solving problems with Honda 08E55-S01-100H. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honda 08E55-S01-100H along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
