Instruction/ maintenance manual of the product Touchscreen Hub 32A30 Home Automation
Go to page of 12
HOME AUTOMATION, INC. Model 32A30 Touchscreen Hub Installation Manual Document Number 32I30-1 Rev B March, 2008.
Copyright © 2005-2008 Home Automa tion, Inc. All Rights Reserved.
INTRODUCTION The HAI Touchscreen Hub is used to provide power, communications, and a video signal to HAI OmniTouch touchscreens. Up to eight (8) OmniTouc h touchscreens, with or without video, can be .
INST ALLA TION NOTE: This unit has protection agai nst static discharge in normal operation. However, use static discharge precautions during in stallation.
CAMERA INPUT TERMINATING RESISTOR JUMPER CAMERA O UTPUT CAMERA P OWER 1.5A MAXI MUM ZONE(+) ZONE(-) HAI CONTROLLER GND(GROUND) B / GREEN A / YELLOW GND MUST BE CONNECTED TO GND O N HAI CONTROLLER CAT 5 CONNEC TORS OMNITOU CH 5.
3. LOW BATTERY INDICATOR (Optional Connection) When the backup batteries connected to the Touchs creen Hub become depleted, there are term inals on the Touchscreen Hub that are used to send a signal to the HAI controlle r to alert you of the low battery condition.
Connecting to OmniTouch (32A00-1) When connecting a standard OmniTouch to the Touchscreen Hub, it is very important to plan where the OmniTouch touchscreen will be inst alled and the gauge/type of wire you will use for the installation. The touchscreen requires a minimum of 4 wires for operation (2 for power and 2 for communications).
5. CAMERA CONNECTIONS The Touchscreen Hub takes the com posite signal from any NTSC cam era, digitizes it throu gh the encoder, and then broadcasts it to the conn ected OmniTouch with Video or OmniTouch 5.7 touchscreens. The Touchscreen Hub supports 6 indivi dual cameras.
6. CONNECTING A SECOND HAI TOUCH SCREEN HUB When connecting more than 8 OmniTouch with Vi deo touchscreens to an HAI OmniPro II or HAI Lumina Pro controller, a second Touchscreen Hub is required.
32A32-2 VIDEO ENCODER NYLON S PACER 32A30-1, -2, -3, -4 TOUCHSCREEN HUB.
8. POWER CONNECTIONS The supplied Power Pack provides both touchscreen (24VDC) and camera (12VDC) power. An AC power outlet should be located within 5 feet. One or two sealed, rechargeable batteries (not included) can be used to backup the touchscreen and camera (optional) power.
SPECIF ICATIONS Operating 32 - 120 degrees F (0 - 49 degrees C) Ranges: 10 - 85 % relative humidity, non-condensing Power Pack: Output 19VDC, 3.79 Amps, Max 72W Input 120VAC, 1.
An important point after buying a device Home Automation Touchscreen Hub 32A30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Home Automation Touchscreen Hub 32A30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Home Automation Touchscreen Hub 32A30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Home Automation Touchscreen Hub 32A30 you will learn all the available features of the product, as well as information on its operation. The information that you get Home Automation Touchscreen Hub 32A30 will certainly help you make a decision on the purchase.
If you already are a holder of Home Automation Touchscreen Hub 32A30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Home Automation Touchscreen Hub 32A30.
However, one of the most important roles played by the user manual is to help in solving problems with Home Automation Touchscreen Hub 32A30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Home Automation Touchscreen Hub 32A30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
