Instruction/ maintenance manual of the product RC-80 Home Automation
Go to page of 19
O M N I S T A T ELECTRONIC COMMUNICATING THERMOSTAT Owner's Manual RC-80 Single Stage Heat/Cool Document Number 13R00-1 January, 1997 : DAY P COOL AUTO Hold Prog Mode Fan OMNISTAT.
Copyright © 1997 Home Automation, Inc. All Rights Reserved.
CONTENTS INTRODUCTION .................................. 1 DESCRIPTION .................................... 1 MAINTENANCE ................................... 1 OPERATION ..................................... 2 DISPLAY .................................
This thermostat is Listed by Underwriter's Laboratories and UL Canada. This thermostat has been tested and found to comply with the requirements of the European Union for Electromagnetic Interference, Electromagnetic Immunity and Safety under the applicable EMI and Low Voltage Directives and Standards.
INTRODUCTION Thank you for purchasing your new RC-80 electronic communicating thermostat. Your thermostat will provide you with comfort, convenience, and energy savings for years to come. We hope that you take a few moments to become familiar with all of the features of this fine product by reviewing this manual.
OPERATION To take advantage of all the benefits and features offered by your thermostat, we recommend that you start by becoming familiar with its operation.
4- Mode Press the Mode key to set the thermostat mode to Off, Heat, Cool, or Auto . In Off mode, the heating and cooling systems are both off and do not respond to changes in temperature settings. In Heat mode, the heating system responds to maintain your desired heating setting.
DISPLAY The following icons will be displayed during normal operation: 1- Temperature Display Shows the current temperature, desired temperature, or heating and cooling settings. 2- Time Display Shows the current time of day. 3- DESIRED DESIRED is displayed when the temperature display shows the desired temperature setting.
5- The is displayed when the heating or cooling system is running. 6- COOL COOL is displayed when the system is in Cool mode. 7- AUTO AUTO is displayed when in automatic changeover mode. 8- HEAT HEAT is displayed when the system is in Heat mode. 9- FAN FAN is displayed when the fan is set to run continuously.
FILTER REMINDER Your thermostat logs the amount of time your heating and cooling system has been running and gives you a reminder when it's time to replace your filter. " F I L t " will be displayed every four seconds in the place of the time display when it is time to change you filter.
SETTING THE CURRENT TIME AND DAY To set or change the current time and day, press and release the Prog key. The hour will blink. 1. Use the arrow keys ( ∧ - ∨ ) to change the hour. 2. Press the Prog key to advance to minutes. 3. Use the arrow keys ( ∧ - ∨ ) to change minutes.
PROGRAMMING Your thermostat may be programmed to adjust the heating and cooling settings up to 4 times per day ( MORN , DAY , EVE , NITE ). You can setup a temperature time schedule for weekdays, Saturday, and Sunday. To enter programming mode, press the Prog key 4 times.
SETTING TIME SCHEDULES To view or change the programming time schedules of your thermostat, press and the Prog key four times. The weekday MORN time will flash. 1. Use the arrow keys ( ∧ - ∨ ) to change the scheduled time for the displayed period ( MORN , DAY , EVE , or NITE ).
6. Press the Prog key to advance to the next period. 10.
Repeat steps 1-6 for the DAY , EVE , and NITE periods. Afterwards, repeat steps 1-6 for 4 daily periods on Saturdays (Day 6), and 4 daily periods on Sundays (Day 7). The temperature display will show "6" for Saturdays, and "7" for Sunday times.
SYSTEM MODE Your thermostat can be connected to an automation system or personal computer. With network software, the remote system can send commands to the thermostat to change mode, cool setting, heat setting, status of fan and hold, and other items.
TIME SCHEDULES The table below shows the time schedules that are currently set into your thermostat. There is a blank table at the bottom that can be used to plan changes to the current schedule.
COOL HEAT.
TWO YEAR LIMITED WARRANTY Home Automation, Inc. (HAI), warrants this product against defects in material and workmanship, under normal use and service, for a period of two (2) years from the date of purchase by the consumer. During the warranty period, HAI will repair or replace, at its option, any HAI thermostat that fails due to defect.
An important point after buying a device Home Automation RC-80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Home Automation RC-80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Home Automation RC-80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Home Automation RC-80 you will learn all the available features of the product, as well as information on its operation. The information that you get Home Automation RC-80 will certainly help you make a decision on the purchase.
If you already are a holder of Home Automation RC-80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Home Automation RC-80.
However, one of the most important roles played by the user manual is to help in solving problems with Home Automation RC-80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Home Automation RC-80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
