Instruction/ maintenance manual of the product OV210 Hobart
Go to page of 20
Phone Hobart Baker y Systems A FORM 31204 Rev. A (Sep. 2003) OV210 SERIES OV210 SERIES OV210 SERIES OV210 SERIES OV210 SERIES RACK OVENS RACK OVENS RACK OVENS RACK OVENS RACK OVENS WITH ELECTRONIC WIT.
– 2 – IMPORT ANT FOR Y OUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 –.
– 4 – TABLE OF CONTENTS GENERAL ............................................................................................................................................. 5 INSTALLATION ..........................................................
– 5 – OPERA TION AND CARE OF O V210 SERIES RA CK O VENS KEEP THIS MANU AL FOR FUTURE USE GENERAL Model OV210G (Gas) and OV210E (Electric) Rack Ovens accommodate roll-in racks. They are equipped with an electronic oven control for baking and/or steaming applications.
– 6 – OPERA TION WARNING : THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. CONTROLS Control Hints • The VENT feature helps control humidity. • The STEAM option requires 20 to 30 minutes to recover prior to each use.
– 7 – CONTROL GUIDE Y E K N O I T C A Y A L P S I D . P M E T . e r u t a r e p m e t d e r i s e d e h t t e s o t s s e r P . d a p y e k r e b m u n e h t g n i s u e u l a v e h t r e t n E t e s e h t s y a l p s i d w o d n i w . P M E T T E S e b l l i w t h g i l N O T A E H e h T .
– 8 – OVEN PREHEAT For the best results, the oven must be preheated before baking begins. 1 . Turn the power switch to the ON position. 2 . Press TEMP. and enter the desired baking temperature on the number keypad. 3 . Confirm that the doors are closed.
– 9 – BASIC OPERATION WARNING : THE OVEN AND ITS PARTS ARE HOT. TO PREVENT BURNS, USE HOT PADS OR PROTECTIVE MITTS WHEN LOADING OR UNLOADING THE OVEN. 1 . Preheat the oven. 2 . Confirm that the doors are closed. This enables the rack carrier to lift and rotate.
– 10 – Quick Set stores up to 84 programs that can be stored in memory and recalled by number when needed. A program is a set of baking instructions - TEMP., TIMER, STEAM and DELAY settings - that the operator defines for any baking operation. 1 .
– 11 – Changing Quick Set Programs 1 . When the power is turned on, the oven defaults to QUICK SET-1. 2 . Press TEMP. and enter 99 on the number keypad. Repeat this step for TIMER, STEAM and DELAY. 3 . Wait for displays to change to 0. 4 . Press TEMP.
– 12 – The temperature and timer controls are factory set to degrees Fahrenheit with minutes set and minutes remaining. If desired, the controls can be changed to degrees Celsius and/or hours and minutes remaining as follows: 1 . Press TEMP. and enter 99 on the number keypad.
– 13 – SHUTDOWN 1 . Remove all remaining product. 2 . Press TEMP. to shut off heat. 3 . Allow the oven to cool, then turn the power switch to the OFF position. 4 . Clean the baking chamber. (See CLEANING.) 5 . For lengthy shutdowns, shut off the main power and the gas and water supplies.
– 14 – MAINTENANCE WARNING : THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING, OR CLEANING THE OVEN. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. GENERAL As Needed • Inspect the area around the oven.
– 15 – O WNER PREVENTIVE MAINTENANCE PR OCEDURE INTRODUCTION This owner preventive maintenance (PM) section includes procedures to inspect for proper operation and cleaning of components.
– 16 – Clean and Vacuum Components and Control/Burner Areas 1 . Clean the control/burner compartment (Fig. 3) area of dust and/or lint accumulation.
– 17 – Inspect Door Components 1 . Check loading door latch. A. Check door gasket for good condition. If door gasket needs replacement, contact your authorized service agency. B. Check loading door latch (Fig. 5), latch must fully extend when door is closed and contacting door gasket.
– 18 – Inspect Air Louvers 1 . Check air louvers (shutters) (Fig. 9) inside oven and tighten any loose screws. 2 . Check oven interior, tighten or replace loose or missing panel screws. Also check floor anchors. Fig. 9 Inspect Cavity Vent 1 . Check vent for proper operation.
– 19 – Verify Ignition Module Safety Lockout Functions (Gas Ovens) 1 . Verify ignition module safety lockout functions. A. Turn the oven on and close the door. B. Set the oven control to call for heat, make sure convection fan is running and the burner has established a flame.
– 20 – D E D E E N S A Y P O C S R E B M U N L A I R E S / L E D O M R E N W O D E D N E M M O C E R T S I L K C E H C E C N A N E T N I A M E V I T N E V E R P S A G - S N E V O K C A R Y R E K A B L L A C N.
An important point after buying a device Hobart OV210 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart OV210 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart OV210 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart OV210 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart OV210 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart OV210, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart OV210.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart OV210. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart OV210 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
