Instruction/ maintenance manual of the product ML-136126 Hobart
Go to page of 12
701 S. RIDGE A VENUE TRO Y , OHIO 45374-0001 937 332-3000 www .hobar tcorp.com F-35109 Rev . A (April 2014) MODEL 4822 CHOPPER ML-136125 ML-136126.
– 2 – © HOBART , 2014 Installation, Operation and Care of MODEL 4822 CHOPPER SA VE THESE INSTRUCTIONS GENERAL The 4822 Chopper uses a 1 1 / 2 horsepower motor . It will grind 16 lbs. per minute, fi rst cutting, through a 1 / 8 " plate. The 4822 Chopper , with funnel-shaped cylinder , will grind 20 to 22 lbs.
– 3 – INST ALLA TION UNP ACKING Remove the carton from around the machine. Remove the four bolts holding the machine to the skid. Unpack the chopper cylinder assembly .
– 4 – CLEANING Unplug chopper power cord before cleaning. The chopper must be thoroughly cleaned and sanitized after installation and before being placed into service.
– 5 – ASSEMBL Y Check to assure the hub and hub drive are clean and clear of any obstruction. Insert the cylinder assembly with a slight twisting motion toward the left. The cylinder stop pin will contact the side of the hole that receives it. T ighten the thumb screw .
– 6 – MAINTENANCE Unplug chopper power cord before cleaning, servicing or removing parts. Replace parts before use. MACHINE CLEAN UP The machine should be thoroughly cleaned at the end of an operating day or after being idle for an extended period of time.
701 S. RIDGE A VENUE TRO Y , OHIO 45374-0001 937 332-3000 www .hobar tcorp.com O D E D' E M P L O I M F-35109 Rév . A (A vril 2014) HACHOIR MODÈLE 4822 ML-136125 ML-136126.
– 2 – © HOBART , 2014 Installation, fonctionnement et entretien du HACHOIR — MODÈLE 4822 CONSER VEZ CE MODE D’EMPLOI INFORMA TIONS GÉNÉRALES Le hachoir 4822 est équipé d’un moteur de 1½ HP (1,12 kW). Il peut hacher 16 lb (7,25 kg) de produit à la minute en première coupe avec une plaque à trous de 1/8 po (3 mm).
– 3 – INST ALLA TION DÉBALLAGE Retirez le carton autour de l’appareil. Dévissez les quatre boulons retenant le hachoir à la palette. Déballez l’ensemble du cylindre de hachage. Aussitôt le déballage terminé, assurez-vous que le hachoir n’a pas subi de dommages pendant l’expédition.
– 4 – NETT OY AGE Débranchez le cordon d’alimentation avant le nettoyage. Le hachoir doit être nettoyé soigneusement et désinfecté après l’installation et avant sa mise en service.
– 5 – MISE EN PLACE Assurez-vous que le moyeu et son entraînement sont propres et libres de toute obstruction. Insérez le cylindre avec un léger mouvement de rotation vers la gauche. La goupille de butée du cylindre entrera en contact avec le côté du trou de réception.
– 6 – FONCTIONNEMENT Coupez la viande en bandes, mettez le hachoir en MARCHE et alimentez-le en vous servant du poussoir seulement si c’est nécessaire.
An important point after buying a device Hobart ML-136126 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart ML-136126 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart ML-136126 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart ML-136126 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart ML-136126 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart ML-136126, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart ML-136126.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart ML-136126. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart ML-136126 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
