Instruction/ maintenance manual of the product ML-104586 Hobart
Go to page of 12
FP350 FOOD PROCESSOR MODEL FP350 ML-104586 FOOD PROCESSORS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 19353 Rev. D (Oct.
– 2 – © HOBART CORPORATION, 1995 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation, and Care of MODEL FP350 FOOD PROCESSOR SA VE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese. A worktable, a wall rack, and a wide range of slicer, shredder, and dicing plates are available options.
– 4 – Fig. 1.
– 5 – OPERA TION WARNING : ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT . Proper assembly of the FP350, including selection of the appropriate cutters, is necessary for correct operation of the food processor. Refer to the Cutting Tool Guide for sizes of cutters and refer to the appropriate operation instructions.
– 6 – 3. To remove the pusher plate, hold the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 4. Take hold of the pusher plate with both hands (Fig. 2). 5. Rotate pusher plate until the pin on the shaft is out of the slot on the bracket.
– 7 – Removing the Cutting Tools 1. Using the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 2. Turn the lock handle counterclockwise and swing the feed cylinder out to the right.
– 8 – CLEANING WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth.
– 9 – CUTTING TOOL GUIDE Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato - use the FINE SLICER, not the STANDARD SLICER. FINE SLICER 1 ⁄ 16 (1.
– 10 – Dicer and French Fry Plates The recommended slicer plate will produce near cube-shaped products. The DICER grid dimension must be equal to or larger than the SLICER dimension. DICER 9 ⁄ 32 (7.5 mm) Use with FINE SLICER 7 / 32 (6 mm), 5 ⁄ 32 (4 mm), 1 ⁄ 8 (3 mm), 1 ⁄ 16 (1.
– 11 – MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to make sure that it is in proper working order. Plates must be clean, intact and sharp. The knife shaft should be regularly lubricated with a drop of mineral oil, NOT COOKING OIL.
– 12 – FORM 19353 Rev. D (Oct. 2000) PRINTED IN U.S.A. SERVICE Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment. Long-term service contracts are available on this and other Hobart products. SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutting results.
An important point after buying a device Hobart ML-104586 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart ML-104586 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart ML-104586 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart ML-104586 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart ML-104586 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart ML-104586, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart ML-104586.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart ML-104586. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart ML-104586 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
