Instruction/ maintenance manual of the product MGR36C Hobart
Go to page of 24
701 RIDGE AVENUE TROY, OHIO 45374-0001 937-332-3000 www.hobartcorp.com FORM 18202, Rev. B (July 2000) MODELS MGR36 AND MGR36C GAS DELI RANGES ML-103870 ML-103871 N S T R U C T I O N S I.
– 2 – © HOBART CORPORATION, 1994 IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
– 3 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation and Care of MODELS MGR36 & MGR36C GAS DELI RANGES SA VE THESE INSTRUCTIONS FOR FUTURE USE GENERAL Your MGR36 or MGR36C Gas Deli Range is equipped with six open top burners. The MGR36 range has a standard oven and is supplied with one oven rack.
– 5 – INSTALLATION CODES AND STANDARDS For proper installation procedures in the United States of America, refer to: 1. State and local codes. 2. National Fuel Gas Code ANSI-Z223.1 (latest edition). Copies may be obtained from The American Gas Association, Inc.
– 6 – Bumper Bars (Convection Oven Ranges Only) CAUTION: Failure to install bumper bars may cause motor damage and may void the warranty. Remove existing #10 screws. Position bumper bars (supplied) as shown. Replace #10 screws and secure bumper bars (Fig.
– 7 – Fig. 3 Fig. 4 3. Assemble the required components as shown in Fig's. 3 and 4. 4. Lift the assembly up, sliding the channels into the space provided at the rear of the range (this may require 2 people). 5. It may be necessary to pull the heat shield bottom out slightly in order to clear the oven flue box area.
– 8 – Fig. 8 Fig. 9 Fig. 7 6. Install eight #10 sheet metal screws (4 to each channel leg) (Fig. 7). 7. From the front, install four 1 / 4 -20 x 2 5 / 16 " long machine screws and secure bolts with locknuts. Do not tighten the screws all the way down.
– 9 – LEVELING Check the leveling of the range. Place a carpenter's level inside the oven cavity across the oven rack(s). Level front-to-back and side-to-side. To adjust the leveling, tilt the range to one side and, using channel locks, unscrew the adjustable leg insert as required.
– 10 – Fig. 10 WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS. USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME. After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.
– 11 – ELECTRICAL CONNECTIONS (CONVECTION OVEN MODEL ONLY) WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 12 – OPERA TION WARNING: THE RANGE AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE RANGE. CONTROLS Thermostat Dial - Standard Oven — Allows operator to regulate the oven temperature from low to 500 ° F.
– 13 – 3. If pilot fails to light, turn main gas supply OFF. Wait 5 minutes and repeat the above procedures. 4. After pilot is lit, turn one open top burner valve ON to remove air from the gas line. Turn burner OFF when gas begins to flow. Nightly Shutdown: Turn burner valve OFF; pilot will remain lit.
– 14 – Convection Oven Light open top burner pilots before lighting oven pilot. 1. Open kick panel (see Fig. 12) and lift up the pilot lighting hole cover. 2. Turn red gas valve ON (located behind the kick panel), purging the gas line of all air (Fig.
– 15 – PREHEATING Standard Oven Turn thermostat to the desired cooking temperature and preheat oven for 25 minutes. To save on gas consumption, do not operate oven at maximum heat when it is not necessary. Turn thermostat down to 250 ° F or OFF when oven is not in use or during idle cooking periods.
– 16 – RACK ARRANGEMENT - CONVECTION OVEN Capacity The convection oven is supplied with three oven racks. The oven cavity provides a five-position rack support for maximum cooking flexibility. The following arrangements are the most commonly recommended.
– 17 – Fig. 19 COOKING CHART FOR CONVECTION OVEN This cooking chart is for convection ovens only. For standard ovens, use your normal recipe times and temperatures.
– 18 – ROASTING TEMPERATURES AND TIMES PRODUCT TEMPERATURE APPROXIMATE TIME Standing Rib Roast 250 ° F 3-4 Hrs. - Rare Oven Ready - 15 lbs. 4-4 1 / 2 Hrs. - Med. Rolled Rib Roast - 20-22 lbs. 275 ° F 4 Hrs. - Med. Veal Roast - 15 lbs. 300 ° F 3 Hrs.
– 19 – RECOMMENDED TEMPERATURES AND TIMES FOR BAKING, Cont'd. PRODUCT TEMPERATURE APPROXIMATE TIME (MIN.) Cookies Rolled or Pressed 350 to 400 ° F 6 to 12 Drop 350 to 400 ° F 6 to 15 Brownies 350 ° F 12 to 20 Yeast Breads NOTE: Yeast breads should be fully proofed for best results.
– 20 – REHEATING PREPARED FOODS PRODUCT TEMPERATURE APPROXIMATE TIME (MIN.) Frozen French Fries 400 to 450 ° F 6 to 8 Frozen TV Dinners 350 to 400 ° F 10 to 12 Frozen Entrees - 1" thick 300 to 350 ° F 10 to 20 Frozen Meals 8 oz. foil package 350 to 400 ° F 20 to 30 CASSEROLES PRODUCT TEMPERATURE APPROXIMATE TIME (MIN.
– 21 – CLEANING WARNING: (CONVECTION OVEN MODEL ONLY) DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING. Do not use Dawn dish detergent to clean the exterior or interior components of the range. DO NOT use scouring powder. It is extremely difficult to remove completely, and accumulations can build up that will damage the oven.
– 22 – CONVECTION OVENS ONLY Keep the convection tube opening (Fig. 20) clear from blockage. If usage of aluminum foil is a common practice during the operation of this oven, be sure to periodically check the convection tube for foil particles. Fig.
– 23 – MAINTENANCE WARNING: THE RANGE AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE RANGE. WARNING: (CONVECTION OVENS ONLY) DISCONNECT ELECTRICAL POWER SUPPLY BEFORE SERVICING THE RANGE. LUBRICATION The MGR36C convection oven motor is permanently lubricated and will not require any additional maintenance.
– 24 – PROBLEM Too much bottom heat. Too low temperature. Side burning. Too much top heat. Uneven bake side-to-side. Uneven bake front-to-rear. Dried out products. Pilot outage. TOP BURNER OPERATION PROBLEM Improper burner combustion. Excessive valve handle temperatures.
An important point after buying a device Hobart MGR36C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart MGR36C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart MGR36C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart MGR36C you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart MGR36C will certainly help you make a decision on the purchase.
If you already are a holder of Hobart MGR36C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart MGR36C.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart MGR36C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart MGR36C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
