Instruction/ maintenance manual of the product EQE Hobart
Go to page of 12
QE, EQE, QEH, & PEQ SERIES ROLL-IN, ROLL-THROUGH FOOD ST ORAGE CABINETS AND PROOFERS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.
– 2 – QE Series Roll-In Food Storage Cabinets.
– 3 – © HOBART CORPORATION, 1992 Installation, Operation, and Care of QE, EQE, QEH, & PEQ SERIES ROLL-IN FOOD ST ORAGE CABINETS & PROOFERS SA VE THESE INSTRUCTIONS GENERAL The QE and EQE Series Roll-in Food Storage Cabinets are available as medium temperature (38 ° F) or frozen food (0 ° F) storage cabinets.
– 4 – Door(s) and hinges can be removed, as follows: 1. Lift up and remove the front trim panel (Fig. 2). 2 . Remove the screws which secure the trim rail cover (Fig. 2), unplug the door switch lead wires and remove the screws which secure the trim rail (Fig.
– 5 – On pass thru models, the recessed floor dimension allows 2 1 / 4 " clearance at both front and rear and 1 / 2 " on both sides. On a front opening cabinet, the recessed floor dimension allows 2 1 / 4 " clearance at the front, 1 1 / 2 " clearance at the rear, and 1 / 2 " on both sides (Fig.
– 6 – PLUMBING CONNECTIONS (PEQ Series Proofer only) WARNING : PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY, AND PLUMBING CODES. Make sure the water supply has proper hardness and pH. The recommended water hardness range is 4 – 6 grains per gallon.
– 7 – OPERA TION CONTROLS (Refrigeration) TEMPERATURE CONTROL — The temperature control is set at the factory, but local conditions may necessitate slight adjustment. To adjust the temperature control, lift up and remove the front trim panel (see Fig.
– 8 – CONTROLS — Proofer and Thaw Proofer (Figs. 12 & 13) On-Off Switch Turns the Proofer Control On or Off. The On-Off switch is not a disconnect switch — ALWAYS DISCONNECT POWER AT THE SOURCE TO SERVICE THE CABINET . ON OFF TEMP normally displays the Set-Point Temperature.
– 9 – CONTROLS — Thaw Proofer (Fig. 13) Thaw Proofer TEMP SET VI EW • F SET % HUM TIMER SET START ▲ ▼ • SET T H A W PR OOF AUTO M ATI C • • • MO D E ON OFF Fig. 13 Press MO D E and ▲ or ▼ to select Proof, Set Thaw, or Automatic mode.
– 10 – REMOTE CONTROL — Proofer and Thaw Proofer (When Equipped) Connect Remote Control 'Phone Jack' to Terminal on Electrical Box on Top of Unit Fig. 14 The Remote Control is used in conjunction with either Proofer Controls or Thaw Proofer Controls described on pages 8 – 9.
– 11 – MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquid dishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit, abrasive materials, bleach or harsh chemicals.
– 12 – FORM 18529 Rev. E (Jan. 2000) PRINTED IN U.S.A. — NOTES —.
An important point after buying a device Hobart EQE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart EQE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart EQE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart EQE you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart EQE will certainly help you make a decision on the purchase.
If you already are a holder of Hobart EQE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart EQE.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart EQE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart EQE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
