Instruction/ maintenance manual of the product CP-S833E Hitachi
Go to page of 32
This Liquid Crystal Projector can display various computer signals and NTSC/P AL/SECAM video signals . Outline (1) High brightness A highly efficient optical system with a UHP lamp ensures high brightness. (2) High resolution Three separate high-definition liquid crystal panels are used for the R, G and B signals.
As these colours may not correspond with the coloured makings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow.
3 Bef ore use Examples of illustrated marks [ Before Use ] Illustrated marks Various illustrated marks are used in this product and instruction manual so the product is used correctly and safely, and also to protect you and others from danger and your property from being damaged.
W arning 4 If any abnormality occur s. · When there is an abnormal smell or smoke, if you use this unit as it is, this could cause a fire or electric shock, etc. When an abnormality is found, immediately turn off the power switch and pull out the power plug from the power outlet.
· If the cord is damaged (core wire is exposed, disconnected, etc.), ask your dealer to replace it. It may cause a fire, electric shock, etc. · Check that no dirt adheres to the power plug and fully insert without any play. If dirt adheres or the connection is incomplete, it may cause a fire, electric shock, etc.
6 Do not place this unit where it gets hot. Be careful since if you place the unit outdoors, in a place exposed to direct sunlight or near a heating device, the cabinet and parts could be affected. Cleaning the lens. To clean the lens, use a generally- available lens cleaning tissue (used for cleaning lens of camera, glasses, etc.
7 Main unit Lens Speaker Speaker Remote control sensor · Use the remote control transmitter within the range of about 16 feet from the remote control sensor and within 30 ° to both the left and right. Cooling fan (exhaust) Names and functions of eac h par t Handle ON indicator This blinks in the standby mode and lights in the operation mode.
8 Names and functions of eac h par t (continued) RGB input terminal D-sub 15pin shrink terminal (1/2) VIDEO input terminal (on video-equipped models only) S-VIDEO input terminal Mini DIN 4pin connector (1/2) VIDEO input terminal RCA Jack (1/2) AUDIO L/R input terminal RCA Jack (1/2) AC IN socket Connect the provided power cord.
9 Remote contr ol transmitter Names and functions of eac h par t (continued) *1 POSITION ON icon When presses POSITION ON button, back light on and icon is displayed. While displaying the icon, you can operate POSITION. Icon is displaying in video mode, but can not operate POSITION.
Slide the battery compartment cover in the direction of the arrow while pressing slightly down on it. 10 Caution Cautions on use of batteries · Do not use batteries not specified for this unit. Also do not use old and new batteries together. It may cause a fire, injury due to burst of battery or liquid leakage.
Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage.
12 7 Press the INPUT b utton or the INPUT SELECT (VIDEO or RGB) b utton to select the sour ce of the signal to be pr ojected on the screen. · The selected signal input is displayed at the bottom right of the screen for 3 seconds. P ower on all connected equipment.
13 Basic operations (contin ued) · To reduce temperature inside the projector (cooling down), fan will rotate for about 1 minute after the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. Press the ST ANDBY/ON button, f or 1 second.
14 Basic operations (contin ued) MA GNIFYING FUNCTION It is possible to display a partially magnified picture. This function can be used in combination with a FREEZE function. [T O CHANGE MA GNIFICA TION] 3 Press the MA GNIFY + b utton. · By doing so, the center of the picture can be magnified as one part, becoming double in size.
15 Press the MENU ( ) b uttons or the MENU ON / OFF b utton. · On-screen menus are displayed on the screen. 1 Select the menu to be adjusted using the MENU ( ) b uttons or DISK P AD . · Menu displayed in green is selected. 2 Select the item to be adjusted using the MENU ( ) b uttons or DISK P AD .
16 RGB signal input VIDEO signal input The menu SET UP serves for the change of parameters influencing the picture and for the move picture position. Adjustments and functions (contin ued) · When sta.
17 Adjustments and functions (continued) The menu INPUT serves for the selection of input source. The menu IMAGE serves of the picture inversion. SETUP INPUT IMAGE OPT. MESSAGE TURN ON TURN OFF SETUP INPUT IMAGE OPT. MIRROR BLANK REVEAL MESSAGE SETUP INPUT IMAGE OPT.
18 The menu OPT. allows you to control communication function etc. Adjustments and functions (continued) SETUP INPUT IMAGE OPT. COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF START UP SETUP INPUT IMAGE OPT. 7N1 8N1 COM. BITS SETUP INPUT IMAGE OPT. 1200 2400 4800 9600 19200 COM.
19 1. Input / output signal Connection to the RGB signal terminal 2. Signal input / output terminal 51 10 6 15 11 D-sub 15pin shrink terminal (Female) 1.
20 3. Example of computer signal Connection to the RGB signal terminal(contin ued) Caution · Some input source may not be displayed properly because they are not compatible with the projector. · Some input source may not be displayed in full size as shown "Display Dots".
21 4. Initial set signals The following signals are initially set. The settings may be different depending on the computer type. In this case, adjust the settings referring to pages 15, 16. Connection to the RGB signal terminal(contin ued) Back porch(b) Back porch(b) DATA HSYNC DATA VSYNC Sync.
22 1. Contr ol signal terminal Connection to the contr ol signal terminal 2. Mouse em ulation 5 1 10 6 15 11 D-sub 15pin shrink terminal (Male) Caution Turn off the power of both the projector and computer before connecting. Connect the computer to the control terminal of the projector using an appropriate cable.
23 Connection to the contr ol signal terminal (continued) PS/2 mouse ADB (Mac) mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 15 CLK D ATA SEL0 RTS GND +5V D ATA GND +5V CLK 2 1 4 3 6 5 2 1 4 3 8 .
24 Connection to the contr ol signal terminal (continued) 3. Comm unication (1) Connect the projector and computer using RS 232C cable. (2) Turn off the computer and after computer is setting up, turn on the projector. (3) Select the data speed (COM.SPEED) and the data format (COM.
25 Connection to the contr ol signal terminal (continued) Contr ol data table Caution If computer sends the undefined command code or data code, Projector can not guarantee operation. Command is consisted of 2 command bytes and following data bytes. 1-st byte indicates the kinds of commands and the length of command.
26 The procedure of getting the Projector status (1)Computer sends the command '20H'+'yyH' to Projector. (2)Projector reply the command '1xH'+'yyH'+data bytes. The procedure of setting the Projector status (1)Computer sends the command '3xH'+'yyH'+data bytes.
27 INPUT S-VIDEO VIDEO AUDIO L R 1 1 1 2 2 2 RGB IN AUDIO IN OUT RGB OUT CONTROL 1 2 12 Example of system setup Connecting v arious equipment. AC Inlet Computer(Desk type) Computer (Note type) VTR with S-VHS out (video model only) VTR, etc.
28 Clean the air filter about every 100 hours or when " CHECK THE AIR FLO W " is displayed. Cleaning the air filter T urn the main power s witich off and disconnect the po wer plug fr om the po wer outlet. 1 Remo ve the air filter fr om the bottom.
29 Lamp Light source lamp has a service life. The picture will become dark or color will be poor when the lamp is used for a long time. If usage of lamp is continued in such cases, it could cause a malfunction.
30 On-screen displa y The following messages are displayed on the screen. Messa g e table *1 This message are not displayed after 3 minutes. But this message are displayed when you turn on the power again. Install the lamp co ver and fix it using scre ws.
31 Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. When y ou think something wr ong A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.
32 Specifications All dimensions shown in inches. · All specifications are subject to change without notice. Dimension diagram 12.6 9.4 4.8 2.9 0.6 (0.4) Product name Liquid crystal projector Model name CP-S833W/E Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system Liquid crystal panel 2.
An important point after buying a device Hitachi CP-S833E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi CP-S833E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi CP-S833E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi CP-S833E you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi CP-S833E will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi CP-S833E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi CP-S833E.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi CP-S833E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi CP-S833E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
