Instruction/ maintenance manual of the product 70VX915 Hitachi
Go to page of 92
LCD REAR PROJECTION TELEVISION Operating Guide for 50VX915, 60VX915, 70VX915 IMPORT ANT SAFETY INSTRUCTIONS ................................................................................ 2-3 FIRST TIME USE ...........................................
IMPORT ANT SAFETY INSTRUCTIONS 2 SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI LCD REAR PROJECTION TELEVISION Our reputation has been built on the quality , performance, and ease of service of HIT ACHI televisions. Safety is also foremost in our minds in the design of these units.
IMPORT ANT SAFETY INSTRUCTIONS 3 ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUNDING CONDUCTORS POWER SERVICE GROUNDING ELECTRODE SYSTE.
ACCESSORIES 4 FIRST TIME USE 1. Remote Control Unit CLU-3841WL (Part No. HL02061) or CLU-3843WL (Part No. HL02063). 2. T wo “AA” size, 1.5V batteries (For Remote Control Unit).
HOW T O SET UP YOUR NEW HIT ACHI LCD REAR PTV 5 FIRST TIME USE ANTENNA Unless your LCD Rear PTV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance.
HOOK-UP CABLES AND CONNECTORS 6 FIRST TIME USE Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products.
HOOK-UP CABLES AND CONNECTORS 7 FIRST TIME USE ANTENNA CONNECTIONS TO REAR JACK P ANEL VHF (75-Ohm) antenna/CA TV (Cable TV) When using a 75-Ohm coaxial cable system, connect CA TV coaxial cable to the ANT A (75-Ohm) terminal. If you have an antenna, connect the coaxial cable to the ANT B terminal.
8 FIRST TIME USE SIDE P ANEL CONTROLS INPUT/EXIT VOL- VOL+ CH- CH+ E F G H f b d e g g i j k MENU/SELECT POWER S-VIDEO VIDEO AUDIO L/MONO R INPUT 5 PHOTO INPUT c h a a MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote.
9 SIDE P ANEL CONTROLS i POWER light This light is on during normal operation. Light Blinking Slowly (2 seconds): television lamp is cooling down. It takes 12-15 seconds to warm up and about 2 minutes to cool down. j TEMP indicator This light is off during normal operation.
10 FIRST TIME USE SIDE P ANEL JACKS AND CONNECTORS The side panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks.
11 FIRST TIME USE REAR P ANEL JACKS a Antenna Input ANT A - A 75-Ohm RF antenna or CA TV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture. ANT B - A 75-Ohm RF antenna input. ANT B can only be displayed as a main picture. ANT B cannot be displayed as a sub-picture.
12 FIRST TIME USE REAR P ANEL JACKS f HDMI1 (High Definition Multimedia Interface) (INPUT 1) About HDMI HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multi-channel audio in a single cable.
13 FIRST TIME USE REAR P ANEL JACKS After the CableCARD is installed, wait until the second screen below appears. The third screen below will appear if a channel is not authorized for viewing.
14 FIRST TIME USE REAR P ANEL CONNECTIONS NOTES: 1. Connect only 1 component to each input jack. 2. Follow connections that pertain to your personal entertainment system. 3. Inputs 1 and 2 can accomodate Composite and Component video signals. 4. Cables are not included with the purchase of this TV , except when noted as “provided”.
15 FIRST TIME USE TIPS ON REAR P ANEL CONNECTIONS • S-VIDEO, HDMI, IEEE1394 and component connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
16 FIRST TIME USE CONNECTING EXTERNAL AUDIO DEVICES CENTER OUT ANT B Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only.
17 FIRST TIME USE CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A MONAURAL AUDIO SOURCE TO INPUT1~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
18 FIRST TIME USE CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A STEREO SOURCE T O INPUT1~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
19 FIRST TIME USE CONNECTING EXTERNAL VIDEO DEVICES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
20 FIRST TIME USE CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE WITH HDMI or DVI CAP ABILITY T O INPUT 1 1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the TV set below .
21 FIRST TIME USE CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE T O INPUT 1 OR 2: Y -P B P R . 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below . 2.
CONNECTING EXTERNAL VIDEO DEVICES 22 FIRST TIME USE CONNECTING A COMPONENT SOURCE WITH DIGIT AL INTERF ACE CAP ABILITY TO IEEE1394 TERMINALS 1. Connect the IEEE1394 cable from the output of the component with IEEE1394 capability , such as a Set-T op-Box or Digital VCR, to the IEEE1394 input terminals shown on the Rear Panel below .
Y our Hitachi LCD Rear PTV is equipped with an A V Network feature. This feature helps to control your external Audio/Video equip- ment (VCR, Set T op Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using your Hitachi LCD PTV Remote Control.
A V NETWORK SETUP WIZARD 24 FIRST TIME USE 5. Follow the steps below to setup your A V network (See page 25-26 for A V Network Codes). SETUP PROCEDURE (DVD setup example below).
25 FIRST TIME USE AUDIO/VIDEO CODES FOR A V NETWORK (not for remote control) VCR BRAND . . . . . . . . . . . . . . . CODE Admiral . . . . . . . . . . . . . . . . 0048, 0209 Adventura . . . . . . . . . . . . . . . . . . . .0000 Aiko . . . . . . . . . .
AUDIO/VIDEO CODES FOR A V NETWORK (not for remote control) 26 FIRST TIME USE Anam . . . . . . . . . . . . . . . . . . 1074, 1609 Apex Digital . . . . . . . . . . . . . . . . . . 1257 Arcam . . . . . . . . . . . . . . . . . . . . . . 1 120 Audiotronic .
27 THE REMOTE CONTROL THE REMOTE CONTROL In addition to controlling all the functions on your HIT ACHI Projection TV , the new remote control is designed to operate dif ferent types of VCRs, CA TV (Cable TV) converters, set-top-box, satellite receiver , DVD players, and other audio/video equipment with one touch.
28 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV a POWER button Press this button to turn the TV set on or of f when the remote is in TV mode. (See page 27 for instructions on how to set the remote control to TV mode.) b MODE Indicator T urns on or blinks to show remote control mode.
29 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV f ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options.
30 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV g DA Y/NIGHT button Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness and contrast to compete with room light.
HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV 31 THE REMOTE CONTROL m A V NET button Press this button to access the Audio/Video network (A V Net) menu.
HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV 32 THE REMOTE CONTROL A V NET LEARNING WIZARD This function of the A V NET makes it more expandable because it allows the user to use equipment that is not supported by the pre-code library , listed on page 25-26.
33 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV n INPUTS button When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR P AD and SELECT button to select the inputs that are being used.
34 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV PHOTO INPUT This feature is useful for viewing digital still pictures from your digital camera using the Photo Input in the side panel of the TV . No. 7/10 03/04/03 1632x1232 Vacation Picture No.
35 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV Jump Slideshow Rotate Slideshow Jump Slideshow Rotate 5 sec Start Interval 5 seconds 5 seconds.. etc. SLIDESHOW Select this menu item to start a slideshow of the Photos in your digital camera.
HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV 36 THE REMOTE CONTROL NOTES: 1. The digital device will be automatically recognized if properly connected. 2. Four (4) IEEE1394 devices can be listed on the menu, but only 1 device at a time can be used.
37 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV o INFO button Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the TIMER is set.
38 THE REMOTE CONTROL HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV p VOLUME (VOL) WHEEL, MUTE button Use the VOL WHEEL ( G or H ) until you obtain the desired sound level. T o reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc.
39 THE REMOTE CONTROL PICTURE-IN-PICTURE (PIP) Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, INPUT :2, INPUT :3, INPUT :4, or INPUT :5).
40 THE REMOTE CONTROL PICTURE-IN-PICTURE (PIP) SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. Main Picture Sub Picture SURF MODE PICTURE-IN-PICTURE Surf Mode PIP automatically scans all active channels (those set in memory) and displays them as PIP sub-pictures or Thumbnail channels.
41 THE REMOTE CONTROL PICTURE-IN-PICTURE (PIP) b P AUSE button If you wish to freeze the sub-picture, press the P AUSE button. This is convenient when trying to write down the address for a mail order company , recording statistics for a sporting event, etc.
42 THE REMOTE CONTROL USING THE REMOTE T O CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. Y ou must first program the remote to match the remote system of your cable box (refer to pages 48-49 for pre-codes).
43 THE REMOTE CONTROL USING THE REMOTE T O CONTROL SET -T OP-BOX/SA TELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver . This remote is designed to operate different types of set-top-box/satellite systems.
44 THE REMOTE CONTROL USING THE REMOTE T O CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player . This remote is designed to operate different types of DVD players. Y ou must first program the remote to match the remote system of your DVD player (refer to pages 48-49 for pre-codes).
45 THE REMOTE CONTROL USING YOUR REMOTE T O CONTROL VCR/PVR FUNCTIONS Operating the precoded function for your VCR/PVR (Personal Video Recorder). This remote is designed to operate different types of VCRs/PVRs. Y ou must first program the remote to match the remote system of your VCR/PVR (refer to pages 48-49 for pre-codes).
46 THE REMOTE CONTROL USING YOUR REMOTE T O CONTROL ADDITIONAL AUDIO EQUIPMENT a b a b a a a A/V NET GUIDE MY AUDIO EQUIPMENT CODE IS: NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes. 2. Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.
47 THE REMOTE CONTROL USING YOUR REMOTE “ENT” BUTTON T O ACCESS THE SPECIFIED INPUT OF THE TV INPUT ACCESS This optional feature allows the user of the remote control to setup it’s ENTER (ENT) button to access the specified input of the TV .
48 THE REMOTE CONTROL PVR/VCR, CABLE, SA TELLITE, DVD AND AUDIO CODES FOR REMOTE CONTROL VCR BRAND . . . . . . . . . . . . . . . CODE ABS . . . . . . . . . . . . . . . . . . . . . . . . 1972 Admiral . . . . . . . . . . . . . . . . 0048, 0209 Adventura .
49 THE REMOTE CONTROL PVR/VCR, CABLE, SA TELLITE, DVD AND AUDIO CODES FOR REMOTE CONTROL NSC . . . . . . . . . . . . . . . . . . . . . . . . 0063 Novaplex . . . . . . . . . . . . . . . . . . . . 0618 Oak . . . . . . . . . . . . . . . . . . . . . . . .
50 ON-SCREEN DISPLA Y ON-SCREEN DISPLA Y (OSD) Locks Chan. Manager Aspect Audio Video Move SEL Sel. Timers Setup 1. Press MENU on the remote control to display the dif ferent features on your HIT ACHI LCD TV . 2. Press the CURSOR P AD to highlight a dif ferent feature.
51 ON-SCREEN DISPLA Y ON-SCREEN DISPLA Y (OSD) Picture Mode Select between the two picture modes; Day and Night. Contrast Adjust contrast. Brightness Adjust brightness.
52 ON-SCREEN DISPLA Y ON-SCREEN DISPLA Y (OSD) Set the Antenna Set Antenna settings. Auto Channel Scan Set Auto Channel Scan. Signal Meter Access Signal Meter . Channel List Set Channel List. Change Access Code Change Lock access code. Engage Lock Choose to lock channel, video input, and/or front panel.
VIDEO 53 ON-SCREEN DISPLA Y Color Brightness Contrast Picture Mode Video Move SEL Return Color Temperature Sharpness Tint Contrast Mode Black Enhancement 100% 50% 50% 50% High SEL Select Day Night Reset Video Settings ANT A/B High Dynamic Picture Mode Day Night Return Next/Prev Locks Chan.
VIDEO 54 ON-SCREEN DISPLA Y Use this function to change the contrast between black and white levels in the picture. Use the CURSOR P AD G or H to highlight the function to be adjusted. Press the CURSOR P AD F or E to adjust the function. Press the SELECT button to select the function settings.
VIDEO 55 ON-SCREEN DISPLA Y This function allows you to Reset the Video Menu Settings of the present input and return it to the Day VIDEO mode. Use CURSOR P AD to highlight functions. Press the SELECT button to select Reset V ideo Settings. Use the CURSOR P AD H to access other video settings.
VIDEO 56 ON-SCREEN DISPLA Y Use this function to adjust and balance the percentage of Red, Green and Blue according to the user ’ s preference in each of the four color temperature settings.
AUDIO 57 ON-SCREEN DISPLA Y Select AUDIO to adjust the TV to your preference and to improve the sound quality . Audio SRS Balance Bass Treble Audio Move SEL Return Audio Source BBE Perfect Volume Internal Speakers 50% Off Stereo On Off 50% LR Hard Change Value Auto Noise Cancel Off Loudness Off Locks Chan.
AUDIO 58 ON-SCREEN DISPLA Y Multi-Channel T elevision Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or 2nd Audio Prog (SAP) which may be a secondary language, weather report, etc.
59 ON-SCREEN DISPLA Y AUDIO Use the functions below if your TV is connected to an amplifier/receiver with optical digital input with Dolby Digital or PCM decoder capabilities.
60 ON-SCREEN DISPLA Y ASPECT Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. Press THE CURSOR P AD G , H , F , E to select menu item. Press THE SELECT button to select. A “ A ” in the box indicates that the feature is ON.
CHANNEL MANAGER 61 ON-SCREEN DISPLA Y Select Channel Manager to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. NOTE: When a CableCARD is installed, Auto Channel Scan will not be available. This feature will automatically store active TV channels in Auto Channel Scan memory .
62 ON-SCREEN DISPLA Y CHANNEL MANAGER This function allows you to review which channels are labeled (CH ID), which have been added to Channel Memory (SCAN), which are protected by LOCK and which are your Favorite (F A V) Channels. Select Signal Meter when using an indoor or outdoor antenna.
63 ON-SCREEN DISPLA Y LOCKS This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. The code to enter the Locks feature is a four digit access code number .
LOCKS 64 ON-SCREEN DISPLA Y Use MOVIE RA TINGS to prevent viewing of any movie that you feel may be inappropriate due to its content. Use the CURSOR P AD G or H to select the MOVIE RA TING category that you want to block. Press SELECT to block the MOVIE RA TING that you have selected.
LOCKS 65 ON-SCREEN DISPLA Y TV Ratings Move SEL Return Status TV-Y: TV-Y7: TV-G: TV-PG: TV-14: TV-MA: Sub Category DL S VF V Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Se.
LOCKS 66 ON-SCREEN DISPLA Y Canadian Ratings (Eng) Move SEL Return Status C: C8+: G: PG: 14+: 18+: Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Select Canadian Ratings (Frn.
LOCKS 67 ON-SCREEN DISPLA Y Canadian Ratings (Frn) Move SEL Return Status G: 8 ans+: 13 ans+: 16 ans+: 18 ans+: Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Select Canadian.
68 ON-SCREEN DISPLA Y TIMERS Select T imers to set your Clock, Sleep Timer , Event T imer and Day/Night Timer Recordings. Locks Chan. Manager Aspect Audio Video Move SEL Sel. Timers Setup Timers Move SEL Return Select Set Day/Night Timer Set Sleep Timer Set The Clock Set Event Timer Set Auto Power Off Locks Chan.
69 ON-SCREEN DISPLA Y TIMERS Select this feature to set your Sleep T imer from 30 minutes to 3 hours (30 minute increments). Timers Set Day/Night Timer Set Sleep Timer Set The Clock Set Event Timer Ti.
70 ON-SCREEN DISPLA Y TIMERS NOTE: 1. When the INFO button is pressed, the Event T imer Icon will only display the current date ON/OFF timer . 2. The Off T imer will only activate if the TV was turned on by the On T imer and no channel selection was made after this time.
71 ON-SCREEN DISPLA Y TIMERS This function will turn off the TV automatically when a video signal is not detected for 15 minutes. Timers Set Auto Power Off Timers Set Day/Night Timer Set Sleep Timer S.
SETUP 72 ON-SCREEN DISPLA Y Select SETUP when setting your TV up for the first time. Use the CURSOR P AD G or H on the remote to highlight the function desired.
SETUP 73 ON-SCREEN DISPLA Y This function allows you to choose from two menu backgrounds. Use CURSOR P AD F , E to highlight Set The Menu Background (shaded or solid), and press the SELECT button to select setting. Press EXIT to quit menu or CURSOR P AD F to return to previous menu.
SETUP 74 ON-SCREEN DISPLA Y Use this feature to give a name to any of the five video inputs. Use the CURSOR P AD to highlight the name of the video inputs. Press the SELECT button to select desired input name. Select Reset to set video names to original factory preset condition.
75 SETUP Caption Display: On/Off will turn the display on or of f. Auto will turn the display on when Mute/Soft Mute is on. Caption Mode: Captions is for the program you are viewing. T ext is for additional information such as news reports or a TV program guide.
SETUP 76 ON-SCREEN DISPLA Y Select this feature to access your CableCARD ID and HOST ID. Please have this information ready when you call your cable operator (see also page 13). CableCARD Info Select the button below to access your CableCARD ID and Host ID.
SETUP 77 ON-SCREEN DISPLA Y NOTE: Any power interruption during the upgrade process will cancel the upgrade. When this happens, repeat the upgrade procedure. Upgrades Move SEL Return Software Version #: Main VXX.XX MMC Software Upgrade Please insert MMC card before upgrading.
78 LAMP REPLACEMENT LAMP REPLACEMENT Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICA TOR light turns on, then it is time to replace the lamp with a new lamp. Lamp Life The lamp life may vary based on usage of the LCD Rear PTV .
79 LAMP REPLACEMENT LAMP REPLACEMENT 120V 1. Turn of f the main power switch and unplug the power cord. CAUTION: THE LAMP IS VER Y HOT AND MA Y CAUSE FIRE OR SEVERE BURNS. W AIT A T LEAST 30~45 MINUTES T O ALLOW THE LAMP TO COOL BEFORE PROCEEDING WITH LAMP REMOV AL.
80 LAMP REPLACEMENT LAMP REPLACEMENT 3. Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover . HANDLE REMOVE SCREWS HANDLE LAMP UNIT 4. Remove the two screws that hold the lamp in place. Remove the lamp unit by holding the lamp handle, then pulling outwards.
81 LAMP REPLACEMENT LAMP REPLACEMEN 6. Without installing the lamp cover , the power will be off and the Lamp Indicator will flash (see page 9). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors.
82 CARE OF YOUR HIT ACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty .
83 RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear , picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths.
USEFUL INFO 84 HIT ACHI Liquid Crystal Display incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR T O HA VE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1.
USEFUL INFO 85 Inputs: • Power Input . . . . . . . . . . . . . .AC 120V , 60Hz • Stand-by Power . . . . . . . . . . . . . . . . . .0.6W • Power Consumption - Refer to rear panel at the back of the T .V . • Antenna input impedance . . . . . . .
USEFUL INFO 86 Hitachi America, L TD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However , should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO 87 In Canada: 1-800-HIT ACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Hitachi Canada, L TD. Digital Media Division Should you have any questions regarding warranty , service, operation, or technical assistance, please contact: Look for your French Manual on the outside of the box.
88 INDEX A Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Antennas (Connecting) . . . . . . . . . . . . . . . . . . . . . . . . .5,6 Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29,60 Audio (Sound Enhancement) SRS .
89 END USER LICENSE AGREEMENT FOR HIT ACHI DTV SOFTW ARE IMPORT ANT – READ CAREFULL Y : This License Agreement is a legal agreement between you and Hitachi America, Ltd.
90 END USER LICENSE AGREEMENT FOR HIT ACHI DTV SOFTW ARE 7. LIMIT A TION OF LIABILITY . IN NO EVENT SHALL HAL-HED OR ANY OF ITS P ARENT OR AFFILIA TE COMP A- NIES BE LIABLE T O YOU OR ANY THIRD P ARTY.
91 NOTES.
QR60661.
An important point after buying a device Hitachi 70VX915 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi 70VX915 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi 70VX915 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi 70VX915 you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi 70VX915 will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi 70VX915, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi 70VX915.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi 70VX915. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi 70VX915 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
