Instruction/ maintenance manual of the product HCW-2 Henny Penny
Go to page of 26
Henny Penny Humidified Counter W armer Model HCW -2 Model HCS-2 Model HCW -3 Model HCW -5 Model HCS-5 Model HCW -8 OPERA T OR’S MANUAL.
.
Model HCS-2/HCW-3/HCW-5/HCW-8 FM05-019-F Revised 02-14-07 LIMITED W ARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warrantie.
Model HCS-2/HCW-3/HCW-5/HCW-8 T ABLE OF CONTENTS Section Page Section 1. INTRODUCTION ....................................................................................................... 1 - 1 1-1. Heated Display Cabinet ...........................
Model HCS-2/HCW-3/HCW-5/HCW-8 SECTION 1. INTRODUCTION 1-1. HEA TED DISPLA Y The Henny Penny Heated Display Cabinet is a basic unit of food CABINET processing equipment used to display the food product and maintain the temperature of hot foods in the commercial food service operation.
Model HCS-2/HCW-3/HCW-5/HCW-8 1-5. SAFETY The only way to ensure safe operation of the Henny Penny Heated Display Cabinet is to fully understand the proper installation, operation, and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures.
Model HCS-2/HCW-3/HCW-5/HCW-8 SECTION 2. INST ALLA TION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Heated Display Cabinet. Installation of this unit should be performed only by a qualified service technician.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-2. UNP ACKING (Continued) 2. Open top flaps and remove packing. 3. Lift carton off skid. 4. Remove four bolts from under skid.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-3. LOCA TION Place the unit on a table, preferably with a cut-out opening below the cabinet to allow easy service connections and serviceability . When setting up the Henny Penny Heated Display Cabinet, be sure to level the table.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-5. DRAIN CONNECTION The drain can be connected to a 1 inch N.P .T . directly below the water well or to a 3/4 inch N.P .T . from the operator ’ s side. W e recommend the 1 inch N.P .T . connection as this will allow straight down draining of the water .
Model HCS-2/HCW-3/HCW-5/HCW-8 2-6. ELECTRICAL CONNECTION The electrical power can be connected from the bottom or from the (Continued) operator ’ s side. There is a 1-3/32 inch diameter hole for either connection. Again, we recommend the bottom connection as this will give a cleaner appearance to the unit.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-8. W A TER SUPPL Y CONNECTION (Continued) This unit as manufactured requires the installation of an appropriate back-siphoning device (as per National Plumbing Code ASA-A40.8-1955) to be connected to the water inlet line.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-10. CABINET DIMENSIONS 1006 2-7 Model HCS-2 Model HCW-3.
Model HCS-2/HCW-3/HCW-5/HCW-8 2-10. CABINET DIMENSIONS (Continued) 2-8 1006 Model HCW-5.
Model HCS-2/HCW-3/HCW-5/HCW-8 SECTION 3. OPERA TING INSTRUCTIONS 3-1. INTRODUCTION This section provides operating procedures for the heated display cabinets. The Introduction, Installation and Operation sections should be read, and all instructions should be followed before operating the cabinet.
Model HCS-2/HCW-3/HCW-5/HCW-8 3-2. OPERA TING CONTROLS (Continued) 3-2 1 03 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6.
Model HCS-2/HCW-3/HCW-5/HCW-8 3-2. OPERA TING CONTROLS (Continued) 103 3 - 3 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-1 1 Figure 3-12.
Model HCS-2/HCW-3/HCW-5/HCW-8 Fig. Item Description Function No. No. 3- 1 1 W ater V alve An electrical solenoid valve energized by the float switch or the water control switch (in manual position) th.
Model HCS-2/HCW-3/HCW-5/HCW-8 Fig. Item Description Function No. No. 3-10 13 W ater Control A three-position switch with center position being OFF; Switch i n the position marked AUTOMA TIC (up), the .
Model HCS-2/HCW-3/HCW-5/HCW-8 Fig. Item Description Function No. No. 3 - 11 2 2 Float Switch An electro-mechanical sensing device used to automati- cally control the water level in the water pan; the .
Model HCS-2/HCW-3/HCW-5/HCW-8 4. Install the perforated bun pans over the water well. This will help in a more rapid heat up of the water . 5. Close the doors. 6. Turn the power switch to the ON position. 7. T urn the light switch to the ON position. 8.
Model HCS-2/HCW-3/HCW-5/HCW-8 3-5. SHUT -DOWN AND 1. T urn the water thermostat to OFF . CLEANUP 2. T urn the radiant heat to OFF . 3. T urn the water control switch to OFF . 4. Open the doors. 5. Remove all the pans. 6. Remove the drain standpipe. 7.
Model HCS-2/HCW-3/HCW-5/HCW-8 4-1. TROUBLESHOOTING GUIDE Product not • Doors are not kept closed • Keep doors closed when holding possible temperature • Product held too long • Only hold produ.
Model HCS-2/HCW-3/HCW-5/HCW-8 G L O S S A R Y HENNY PENNY HOLDING CABINETS air temperature probe a round device located inside the cabinet that measures the inside air temperature and sends that infor.
Model HCS-2/HCW-3/HCW-5/HCW-8 probe clip a metal holder that attaches to the outside of the control panel to hold the food probe when not in use; the clip is an optional accessory product load capacit.
*FM0 5 - 0 19 - F * Henny Penny Corp., Eaton, Ohio 4532 0, R evised 02-14-07 Henny Penny Corporation P.O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax Toll free in USA 1-800-417-8417 1-800-417-8434 Fax www.
An important point after buying a device Henny Penny HCW-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny HCW-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny HCW-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny HCW-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny HCW-2 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny HCW-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny HCW-2.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny HCW-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny HCW-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
