Instruction/ maintenance manual of the product 401C001001 Hayter Mowers
Go to page of 28
POWER TRIM Code 407C OWNER’S HANDBOOK FROM SERIAL NO:407C001001 P ART NO: 407005 (rev .0.) ISSUE: 01-03-05.
2 F-050202L T ABLE OF CONTENTS OWNER’S INFORMA TION 4 SAFETY PRECAUTIONS 4 INTERNA TIONAL PICTORIALS 7 ASSEMBL Y 8 OPERA TION 1 1 MAINTENANCE 14 TROUBLE SHOOTING CHART 20 REP AIR P ARTS 22 Declared vibration emission values in accordance with Directive 98/37/EC.
3 F-050202L Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase.
SAFETY RULES 4 F-050202L OWNER’S INFORMA TION Know your product: If you understand the unit and how the unit operates, you will get the best performance. As you read this manu- al, compare the illustrations to the unit. Learn the location and the function of the controls.
SAFETY RULES 5 F-050202L 18. Before each use, inspect the throttle control lever and cable. Make sure that the cable is free and that the lever is not damaged. Also check the cable linkage running to the carburetor for kinks, loose fittings, and obstructions.
SAFETY RULES 6 F-050202L 2. Never run an engine indoors or inside a closed area. 3. Never make adjustments or repairs with the engine running. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental start- ing. Always wear eye protection when you make adjustments or repairs.
SAFETY RULES 7 F-050202L INTERNA TIONAL PICTORIALS IMPORT ANT : The following pictorials are located on your unit or on literature supplied with the product.
ASSEMBL Y 8 F-050202L ASSEMBL Y CONTENTS OF P ARTS BAG 1 - Owner ’s Manual 1 - Parts Bag 1 - Safety Glasses (Not shown actual size) 2 Sets - Trimmer Lines (0.155 inch diameter) 1 - Bag (4 Screws) W ARNING: Always wear safety glasses or eye shields while as- sembling the machine.
ASSEMBL Y 9 F-050202L HOW TO RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position.
ASSEMBL Y 10 F-050202L ENGINE PREP ARA TION Note: Engine does not contain OIL or PETROL. W ARNING: Follow the engine manufacturer ’ s instructions for the type of petrol and oil to use. Always use a safety petrol container . Do not smoke when adding petrol to the en- gine.
OPERA TION 11 F-050202L KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERA TE the machine. T o familiarise yourself with the location of the controls, compare the illustrations with your machine. Save this handbook for future reference.
OPERA TION 12 F-050202L HOW TO USE THE TRIMMER HEAD DRIVE LEVER 1. T o engage the trimmer head, hold the con- trol bail against the handle . Move the trimmer head drive lever forward to en- gage the trimmer head. See Figure 6. The faster the engine runs, the faster the trim- mer head will rotate.
OPERA TION 13 F-050202L HOW TO ST ART THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. W ARNING: Never leave the ma- chine unattended while the en- gine is running.
MAINTENANCE 14 F-050202L CUSTOMER RESPONSIBILITIES SER VICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SER VICE DA TES.
MAINTENANCE 15 F-050202L LUBRICA TION How T o Lubricate The Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly . Use a grease gun with au- tomotive type grease to lubricate the jackshaft assembly as shown in Figure 10.
MAINTENANCE 16 F-050202L SP ARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked. 1. Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire brush).
MAINTENANCE 17 F-050202L SER VICE AND ADJUSTMENT W ARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. HOW TO REPLACE THE TRIMMER LINE For the best performance, use a heavy gauge 3.
MAINTENANCE 18 F-050202L HOW TO REPLACE THE DRIVE BEL T T o replace the drive belt, the trimmer head and shield must be removed as follows. W ARNING: Before you remove the drive belt, disconnect the wire from the spark plug. 1. Remove the two fasteners that hold the rear o f the shield to the trimmer housing (See Figure 15) .
MAINTENANCE 19 F-050202L STORAGE W ARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirty days or more, follow the steps below to make sure the machine is in good condition the following season.
TROUBLE SHOOTING CHART 20 F-050202L TROUBLE CAUSE CORRECTION Engine does not start Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug. Fuel tank empty .
TROUBLE SHOOTING CHART 21 F-050202L Engine overheats. Engine cooling system clogged. Clean debris screen and engine cooling fins. Carburetor out of adjustment. Adjust carburetor . T ake the unit to an authorised Service Dealer . Oil level is low . Add oil.
Code 407C REP AIR P ARTS 22 F-050202L 1 2 3 4 5 28 6 2 7 6 8 4 9 10 9 10 4 11 16 17 11 14 12 15 14 20 22 29 23 27 16 19 30 17 6 20 25 24 31 26 33 19 32 32 34.
Code 407C REP AIR P ARTS 23 F-050202L Key No. Description Part No. 1 Lever , Stop MU740198E549 2 Bolt MU323035 3 Cable, Control Latching MU740193 4 Tie, Cable MU071372 5 Handlebar MU740196E701 6 Nut M.
Code 407C REP AIR P ARTS 24 F-050202L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 17 18 19 20 22 23 24 25 26 27 29 30 31 31 33.
Code 407C REP AIR P ARTS 25 F-050202L Key No. Description Part No. 1 Nut MU015x84 2 Screw MU025x1 1 3 Frame, Trimmer MU740150E549 4 Screw MU26x256 5 Bracket, Idler Assembly MU740231 Z 6 Bolt MU009x48 .
NOTES 26 F-050202L.
NOTES 27 F-050202L.
28 F-050202L How T o Order Replacement Parts Use only manufacturer ’ s authorised or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a P A for purchased assembly .
An important point after buying a device Hayter Mowers 401C001001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hayter Mowers 401C001001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hayter Mowers 401C001001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hayter Mowers 401C001001 you will learn all the available features of the product, as well as information on its operation. The information that you get Hayter Mowers 401C001001 will certainly help you make a decision on the purchase.
If you already are a holder of Hayter Mowers 401C001001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hayter Mowers 401C001001.
However, one of the most important roles played by the user manual is to help in solving problems with Hayter Mowers 401C001001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hayter Mowers 401C001001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
