Instruction/ maintenance manual of the product HNC800PTZ Hawking Technology
Go to page of 20
1.
2.
1. I n s t a l l a t i o n 4 1.1 Software Installation 4 . U s i n g t h e I P S e t u p W i z a r d 9 2 . 1 U s e r I n t e r f a c e 9 2.1.1 Action Buttons 11 2.1.2 Function Buttons 12 2 . 2 S e t u p 1 3 2 . 2 . 1 S y s t e m S e t t i n g s 1 3 2.
1.1 Software Installation The steps that follow will guide u th rough the software installation process. TEP 1 yo S : Insert the Hawking Net-Vision TM HNC800PTZ Installation & Utilities CD into your CD-ROM Drive.
STEP 2 : You will see several links on the right hand side of th e CD Autorun’s main page (Figure 1-1). Click on “IP etup & Utility” to enter the page for the IP Setup Wizard and Management & Control Software. (See Figure 1-2 below.) S Figure 1-2 .
STEP 3 : You will see several links on the right hand side of th e IP Setup Wizard and Management & Control Software page (Figure 1-2). Click on “IP Setup”. This will launch the InstallShield Wizard that installs the IP Setup Wizard program on your PC.
STEP 5 : Select a program folder to install the IP Setu p Wizard application into and then click on “Next”. (See Figure 1-5 below.) Figure 1-5 . Select a program folder STEP 6 : Click on “Finish”, to com plete the installation. (See Figure 1-6 below .
STEP 7 : Once the IP Setup wizard has b een installed onto your PC, an IP Setup icon will appear on your PC’s Desktop. Click on is icon to run the IP Setup wizard.
2.1 User Interface the IP Setup program will search for similar cameras ilar” camera will have the same code of four letters at the beginning of its serial n umber.
After the IP Setup Wizard has finished searching, the interface shown in Figure 2-2 will appear. You ca n select any device in tailed explanation of how the IP Setup Wizard Figure 2-2 . IP Setup Wizard user interface the list by clicking on the ch eckbox to the left of the device .
The IP Setup Wizard allows you to set up or upgrade multiple devices (of the same model) at the same time. If you select different models, the buttons will be disabled.
Clicking on this button will remove all the selected devices fro m the device list. The devices that you remove may show up again if you click on t he “Search” button or if you add them into the list manually. Clicking on this button will open a web brow ser to the web user interfaces for all of .
2.2 Setup n settings of the selected device(s). After clicking on the “Setup” button, the IP Setup Wizard will try to connect to the elected device(s). If authentication fails, it will prompt a popup dialog (see Figure 2-6) to ask for the correct password Figure 2-6 .
2.2.1.1 Change Host Name .2.1.2 Change r oot passwor d o change the administrator’ in both the “Root password” and “Confirm assword” text boxes. For security pu rposes, the new password will be displa yed as asterisks in both boxes. The aximum password length is 14 characters.
y ping, so that you input the values correctly. The third way, “ Automatic ”, allows you to make the network camera automati cally synchronize with ti me-servers over the Internet licking “Next” in ndow. In this indow, you can change the network camera’s IP address, subnet mask, default gateway/router, primary DNS, and econdary DNS.
2.2.3 Apply to selected device(s) Figure 2-9 . “Apply” page After configuring all the settings and clicking the “Nex t” button, the “Apply” window will appear. Click on “Apply” to apply/confirm the changes to the selected device(s) or click on the “Previous” button to go back to the previous window and modify the settings.
2.3 Upgrade When you select one device or multiple devices (of the same m odel), the “Upgrade” button will be enabled. Click on it to pgrade the firmware of the selected device(s). After clic king on the “Upgrade” button, t he IP Setup W izard will try to onnect to the s to ask for the correct password nd HTTP port number .
Fi w Figure 2-12 . Camera Info gure 2-13 . Upgrade windo 18.
2.3.2 Package Information he package inform hat you elected: Firmware version: The version number of the selected firmware. Supported script version: The maximum script version th at the firm ware can support. Web page version: The version number of the web page.
2.3.4 Upgrade he “Upgrade” button to upgrade the firmware for the selected device(s). A dialog will pop up to display the rogress of the upgrade process. (See Figure 2-15 below.) Afte r the update process has completed, please click “Done” to nish.
An important point after buying a device Hawking Technology HNC800PTZ (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hawking Technology HNC800PTZ yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hawking Technology HNC800PTZ - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hawking Technology HNC800PTZ you will learn all the available features of the product, as well as information on its operation. The information that you get Hawking Technology HNC800PTZ will certainly help you make a decision on the purchase.
If you already are a holder of Hawking Technology HNC800PTZ, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hawking Technology HNC800PTZ.
However, one of the most important roles played by the user manual is to help in solving problems with Hawking Technology HNC800PTZ. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hawking Technology HNC800PTZ along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
